-
Diffret status for thermostats that are not linked to a zone
In order to stop a room calling for heat and switching on the boiler (like a toilet, closet etc) you can remove the zone controller for the room. It would be good to acknoladge this on the tile in the app.. currently regardless of the zone set for the room it will say "heating to" i think the rooms that are assigned a zone…
-
Date scheduling
Hi, it will be a great opportunity to be able to schedule from starting date and end date, please. The away option is not an option I like to use because off security. What will happen if some one hack my Tado account, and they have full information that I am away. So please add the option to scheduling from starting date…
-
Add detailed status info to tado app for Wireless Receiver connection problems
I recently reported that the wireless link and error LEDs on my Wireless Receiver were often flashing together to indicate a lost connection. tado support said they have access to detailed connection status information with date / time of error events. This type of data would be very useful for us customers to help…
-
Add Zone Control switching to schedule . . .
It would be useful if the zone controller / non zone controller switch could be made a feature of the schedule. There are times here when I’d like to heat a room individually (because no other rooms are on then and it needs to be able to call for heat) but for all it’s other “sessions” the rest of the house is being heated…
-
Better preseve room temperature
I noticed that tado is not good at keeping a stable room temperature. Instead of turning the heating on in advance while temperature is dropping close the level, it turns on when it’s just below. But that will be too late and thus after some time it increases the power to get the temperature higher which is waste of…
-
Keep the radiator valve open for a while after the temperature has been reached.
So the smart thermostat button works like this. You set a temperature like 20 degrees. However the room is19 degrees. Tado turns the valve of the radiator open and your central heating boiler starts heating. However after the temperature has been reached, Tado gives a stop signal but immetiately shuts down the radiator…
-
Show the water temp that goes into a radiator or warn if too low
So, I had an issue with our central heating. Two-story apartment, the lower floor was fine, the upper floor not so much. Out of three radiators upstairs, one was kinda happening, the rest cold. I noticed it was a bit chilly. I played around with the two cold ones, removed the thermostat, and eventually called the landlord…
-
WiFi 6 capability/upgrade
Hi with 3 floors to my house the wireless capability to speak to a single bridge may be causing issues for me. Is there a solution that provides far. Ore effective wifi6 capability or comparability with a wifi6mesh network? TIA
-
dealing better with low battery: add a new battery state "yellow"
i have noticed a couple times that i get a tado e-mail that a device needs new batteries but when i look at the app it will show a green battery icon and "good" the cause is, i think: during a cold night the batteries have lower capacity and the e-mail get sent. the app will also show a red icon when looked at right after…
-
Relative units in Energy IQ setup
In residential buildings there are still some individual radiator meters. In the Energy IQ setup one can only give kWh or m3 as unit but this is only available on a building level. Can something be done to use individual meter readings from Techem meters for example?
-
Redundancy in the event of internet loss of server faults
Currently Tado does not have an effective method of controlling their system locally if the internet goes down or if their is a fault on their servers. Can tado re assess this and provide a way to still use the heating controller locally via a smart phone connected to the same WIFI network as the Tado devices, so that in…
-
UK Customer Service Telephone Number
Currently no UK customer service telephone number is available. This is not good for Elderly people who are less technically endowed then other generations and when they have a fault just want to speak to someone to get the fault rectified especially in the Middle of a UK winter. It causes allot of anxiety. Given the…
-
Community Support..
Because there seems to be no input from Tado in this community support why don't they follow Sky's model whereby there are superusers that can elevate some queries to Tado directly for online support vie a chat process. Seems to work ok for them and would greatly reduce the frustration some do have with no input from Tado…
-
Settings after signal loss and auto-reconnect
Regarding the wireless receiver of the central heating, it is undesirable for it to remain on when there is no signal. I have returned several times to a home with tropical temperatures after the signal was lossed for unknown reason (so far) and the heater remains (last setting before disconnection). Can't this be set to…
-
Antifreeze & déactivation possibilty
Hello, Support told me that it s not possible to deactivate or change the antofreeze temperature. The minimum temperature when you set to off is 5°C. I would like to be abble to set the antifreeze temperature at a temperature below 5°C (as set by default). And also to be abble to deactivate completely a radiator head. This…
-
[Released with Offline Schedule] Offline notification
Note from tado°: With tado°'s Offline Schedule (requested on the community for V3+ and always available for tado° X), a text block appears in the app confirming tado° is offline. This is not a notification, but it is a way to inform users when this occurs. Original Post: My Internet Bridge went off-line and I didn't…
-
Switching between Zone Controller and No Zone Controller/ Universal Switch
Please could you incorporate a universal switch for Zone Controller, so that the user could switch all his TRVs to "No zone controller" and back to the specific Zone Controller with a single toggle button? Currently, it's really annoying having to go to Settings -- Rooms & Devices -- The name of a TRV -- scroll to the very…
-
Need to add an additional Heating Unit in the Energy IQ feature (Cubit Feet) for the UK
I'd like to request that the Tado Development team add an Heating Unit of Cubic Feet (ft3) in the Energy IQ part of the app. At the moment, there is only m3 (cubic metres) and Kwh there at the moment, and a huge number (Millions) of UK homes have gas meters with cubic feet callibration not m3 or kwh. Without having Cubic…
-
Monitoraggio finestre aperte
In Tado non esiste un report relativo al monitoraggio delle finestre aperte durante la giornata. Propongo, se possibile e non troppo oneroso, di inserire questa nuova funzionalità che ci dica: - tutte le stanze in cui si è verificato il rilevamento con gli orari - quante volte in quella stanza si è verificato - le…
-
Show end time while editing the duration of a heating override in the tado (web)app
When temporarily overriding the heating schema (e.g. I temporarily want to heat up a specific room), I can choose for how much time I want this override. However, I typically want to directly see at what time this override will stop, not only how long it takes. So basically, when setting the duration of the override, it…
-
Wireless Internet Bridge
This is a super simple idea, and franky it surprises me you haven't done this yet (or have you?), but wouldn't it make sense to have an alternative do the Internet bridge with a wireless antena? I have my home fairly well covered with a mesh wireless connection, but the fact that you need to have all radiators connected…
-
Alert
It would be good if there was a log file so that you could find out which window alerted "open window"
-
Open mode
I suggest to incorporate to smart radiator thermostat the possibility of allowing the valve to remain open, even if it exceeds 25 degrees
-
Can Geofencing button be put higher in the home screen
I use my geofencing button very often in order to switch manually from "home" to "away". I would like to have this button on top. After all, it over-rules all other buttons Can this button be added to the function button "Reorder Rooms". This way, I can put the button where I want it Thanks
-
Global boiler override schedule
My system gets turned on a lot as different rooms heat up at different rates. I’d like to have a global boiler override schedule so I can ensure it’s always off at certain times (including heating and hot water) rather than having to try and set weird on/off blocks for every room throughout the night/day to try and save…
-
Global Device Error History
There's various system errors that are actionable and useful for the user to review for troubleshooting, if only they could review the relevant past historical info in one place focused solely on problems. An error log. lost signal periods for TRVs, sensors, receivers disconnected internet periods for the internet bridge…
-
thermostat mode
Hello, the choice to eliminate the possibility of setting the operating mode on the thermostat (legacy mode) to turn off the air conditioner "manually" is wrong; it was a very useful option.
-
Comfort screen settings
Ability change the comfort range and set a min/max in the comfort toggle
-
Default for adjusting a TRV should be “until next change” or at least set as default
I quite often increase the heating in the front room using the TRV. That seems to set the temperature “until you resume the schedule” whereas if you use the app the default is “until next change”. This has resulted in me leaving the heating set on 20oC overnight a few times. Is there a way to change the default setting? If…
-
Temperature Display
Hi When you blink the display from the app can it display the current temperature rather than a pointless message. Regards John