-
More detail on device errors - Wireless Receiver
Quite often the Wireless Receiver is showing 'device errors' (blinking hazard light) but none of the devices actually have any issue. I believe that this condition is also explained by the fact that a software update may be in progress. However, this is not at all obvious. It would be really good if there was an option to…
-
3 modes for radiator thermostats: Off, Open start boiler, Open dont start boiler
There are times when I'd like a room to warm up "if the heating is on anyway" but I can't justify running the boiler just for that one room, this is possible on a permanent basis by not setting a zone controller, but I'd like the ability to schedule it. e.g. In my bedroom I'd like the radiator to heat up on a morning…
-
Better Boost
Please look into allowing the user to control the temperature of the "boost" facility. 25°C is way too high
-
Report all disconnections/failures clearly in the app
Some device disconnections/failures will immediately show in the app via a change in the icon for the relevant room and changes to the reporting in the climate chart. However other devices are for some reason set up to fail quietly. For example an extension kit controlling the boiler can disconnect and the user will not…
-
Switch off bridge LEDs/Extinction des LEDs du bridge
I would liké to Switch off LEDs on bridge. Brigthness IS toi high and it could save energy. Bonjour, J'aimerais pouvoir éteindre les LED du bridge qui éclairent tout mon salon et ça ferait aussi une économie d'énergie. Merci
-
Internet bridge extender
I need an Internet bridge signal extender for a total coverage of the house.
-
Air Comfort suggestions
Hello, We're supposed to make energy savings with Tadoº, but it's quite inappropriate to get a suggestion to turn the heating on when a room is just below 20ºC. The World Health Organisation recommends a room temperature of around 18°C in Winter, and The Energy Saving Trust advises setting the thermostat to around 18-21°C,…
-
Can we have a Widget
Hi, I feel that you brilliant technology would benefit hugely from a Widget, enabling a screen on my smartphone to be live feeds from the zones of my home
-
Constant Display
I would like the option to see a constant display on my wall control, thus not having to press a button to see the temperature. :)
-
Immersion Heater Switching
Can Tado please modify the Hot Water Controller. This debacle (on Tados recommendation) has lost me £165. I sent Tado all tech data and photos for them to study, and on their recommendation I purchased the wireless thermostat starter kit with hot water controller and the wired thermostat from Amazon because it was on…
-
Support scenes for HomeKit and expose Quick Actions as shortcuts
Dear tado team, Defining schedules in the tado app is great, however there is little integration with Homekit, which makes building of one's smart home setup hard. It would be fantastic if you'd expose Quick Actions (Turn off the heating, Resume schedule in all rooms, Resume schedule per room) available as scenes for…
-
Low Battery Display
Hi would it be possible to show battery status on main menu where all rooms are displayed, this would save going to settings menu to check battery status. Many thanks Stuart
-
switching between accounts
It could be common that families have more than one home (a main one and the second by the sea or in the mountains) then they need to create more than one account to manage different homes thermostats. I can understand, but not completely, your choice to separate account for each home but you have to facilitate the users…
-
Extend your gateway coverage
For those who are desperately asking Tado for years to add some range extender option to their product line-up, what follows may be worth reading :-) Recently, as I was in the process of adding TRV's in rooms located in my attic, I faced the "good old" historical coverage issue of Tado's gateway. The big issue is the fact…
-
Adjust whole HOME by 1 degree up/down
It would be great if you could increase or decrease the whole HOME (every currently active room) by 1 degree just by using one control.
-
Add hot water boost - instead of manual control under hot water settings
In order to boost the hot water for a time period (eg 1 hour) you have to go into Rooms & devices, settings, hot water and then finally access the manual control. It would be a lot easier and more user-friendly and intuitive if there was a simple boost button under Hot water icon. In case anyone is following all the…
-
Bespoke Geofencing
Would it be possible to link a specific room to a member of the household so that when that person is away from the house, his or her dedicated room (e.g. Bedroom) is geofenced and their room heating is switched off?
-
Service Mode for Boiler Maintenance, Draining and Power Flushing
Hello, It would be important to have a Service Mode setting, where: all radiator thermostat valves are fully open and in manual mode: can be individually set to fully open or fully closed boiler control is set to off and in fully manual mode: on or off any timers and automatic "return to schedule" are disabled This is…
-
Allow display of ambient temp always on by an optional setting
The display looks great, unfortunately my previous thermostat used to display the ambient temp which was really handy. Would be great to display it all the time or on a schedule—yes I realise this will affect battery life but users should be able to choose the trade off.
-
Provide estimated gas consumption from the boiler
Where possible and depending on the boiler model, would very useful to get an estimate on gas usage if the boiler can provide such.
-
Bug in the way heating activity is calculated
According to Tado's app my heating system has been on for 20h per day on average during the last month, and 24 full hours the day before yesterday. In reality my boiler has been on for only about 10 minutes the day before yesterday, and the same goes for the rest of the month. The reason for this funny discrepancy becomes…
-
Merge "deleted rooms" with a new room created
I have deleted a room and re-configured again due to malfunctioning radiator thermostat. Now in my "heating activity" dashboard it shows the history of this room in "deleted rooms". Is there any ways to merge this deleted room to the new one I've created so the statistics aren't disturbed?
-
Apple Watch & Mac app
Would love to see the app extended to the watch and Mac app store please
-
Support for multi-zone UFH manifolds
The current integration with underfloor systems appears to be limited to single zone systems without zone actuators. A lot of UFH system are UFH downstairs with radiators upstairs. The UFH system typically have more than one zone with actuators per zone and a shared pump. Currently, I can get a multi-zone UFH management…
-
Calibrate radiators with room thermostat
I have 5 rooms setup with smart radiator thermostats but only need one wireless thermostat for my main living area. It would be great it I could calibrate my other rooms by placing the room thermostat in each room for ‘x’ amount of time to automatically set the temperature offset.
-
A link to new feature releases
Could you add an Updates link where you can see all the recent and previous feature updates you’ve made. Use case: I just opened up the app and saw the ‘child lock’ feature you added, but stupidly, I hit ‘skip’ and now can’t find an (easy) way of finding it again.
-
Better overview of all schedules in one view
I’d find it really useful to have an overview of all the schedules of my smart valves so I can see when the heating generally kicks on and off to be able to review my system more efficiently. At the moment I have to check every valve individually just to see I’m when everything turns off and on in order to refine my setup
-
Diffret status for thermostats that are not linked to a zone
In order to stop a room calling for heat and switching on the boiler (like a toilet, closet etc) you can remove the zone controller for the room. It would be good to acknoladge this on the tile in the app.. currently regardless of the zone set for the room it will say "heating to" i think the rooms that are assigned a zone…
-
Group rooms
Can you add a feature to group rooms (i.e. ground floor / first floor etc) to a cluster to be able to boost / switch off with one click.
-
The Tado is not Smart Enough
I worked on heating systems before the Internet. Commercial Heating systems used Optimisers. They were quite complex in operation and learned over time. But the controls were simple. It had an outside temperature sensor and an internal temperature sensor as a minimum. You programmed in occupancy times. If the outside…