-
Be able to set max outgoing water heating temperature in central heating (CV)
In the Netherlands most people have a central gas heater which pomps hot water around in the house through floors, radiators or convectors, also called in Dutch: CV installatie. What I cannot do with Tado is adjust the outgoing hot water temperature of this central heater, via an OpenThem connection, but I cannot adjust…
-
Don't completely disable a room from remote control because 1 device has fallen over.
I searched but failed to find similar though I suspect it is here somewhere..... In a room where there are multiple tado devices (my open plan ground floor has 1 thermostat and 3 trvs) if one device becomes disconnected the entire room is impossible to access. This seems mad. I can't find out the current temperature…
-
Admin users and managed users
Admin users have full access to tado, and managed users just able to adjust the temperature in rooms for a set time period.
-
Simple Improvements to App Homescreen View
I'd like to suggest a couple of simple improvements (IMHO) to the content of the homescreen room tiles in the Tado app: The tile is large, and there is plenty of spare space on it, so could we get an indicator of the room's temperature behaviour. What I mean is that if the room temperature is rising then an arrow pointing…
-
Expose temperature sensors to Apple Homekit
As the title says, would be handy to have access to the temperature sensors in Homekit to create automations e.g. when temperature reaches X do Y
-
Boiler Overun
When all heating demand is stopped our boiler goes into overrun and dissipates it heat into the garage (where it is not required). It would be good if when the heating is not called for boiler heat demand signal is stopped but the radiator valves would stay open for a adjustable time to use the stored boiler heat in…
-
Multiple accounts in 1 Tado App
Being a fan of Tado, I introduced to both my kids and mother in law. My mother in law needs some assistance, and in case, I can have the control from my home. But needed an other divice, because it's not possible to have 2 accounts on the same app. Is it possible to add multiple accouts / living address to 1 app on 1…
-
Enable eBUS support for Tado X Wireless receiver
The V3+ supports both eBUS and Opentherm however the newer product series X does not support eBUS. Please enable also eBUS support for the X series. I imagine since you have the code for V3+ in the firmware it could be refactored over for the X and with a firmware update it could work.
-
Switch between rooms in graph nice
When in graph mode, one can change the date range with the ˅ symbol next to the date. It would be so much easier to switch between rooms if there was a ˅ next to the Room/Device name as well. Now I have to go back twice (first to the Room, then to the home screen) to select a new room and view the graph
-
Suggestion: enable Homekit Away/ Home automation
Tado should allow homekit users to toggle the home / away status of tado, using homekit automations. Issues; - Expensive - Tado charges £29.99/y just to toggle auto geofencing (extortion). - Privacy issues - I have to always share my location data with tado. I don't want to do this. - No support for guest / multi house…
-
1hr boost
It would be very helpful to be able to set a timer for boosting a heating zone. Some time I would like to have the heating on either upstairs or downstairs outside the scheduled times. More often than not I set it manually but I always forget to turn it off. Since I have underfloor heating the temperature raises very…
-
Heating Activity - Real Time
Hello, Whilst "Heating Activity" is good at showing which zone/room is currently heating, what is not in anywhere near real time is the Total Today value. It will sometimes take hours before the Total Today time changes when I know the heating has been on for more than the total of 11 minutes it has kept telling me.. I may…
-
Schedule profiles
I have now had the tado system for nearly a week, and its certainly better than my old hive system. You guys have done a good job on it. However you (and every competitor) are missing what I believe is probably an important feature for many people, and I can say 100% would have made me choose to move to you years ago had…
-
Make Opentherm boiler specific tweaks possible
Hi! I'm having an issue with opentherm using my boiler Enbra CD34H. After some troubleshooting I found out that issue is caused by Opentherm message ID 14 (Maximum relative modulation) being send too often by Tado (every 6s). Unfortunately support is unable to change this to 2mins intervals (which would fix the issue) for…
-
Comfort screen settings
Ability change the comfort range and set a min/max in the comfort toggle
-
Integrate with smart meter
Stop wasting my time with app notifications to key my meter reading to get smart eq working
-
Holiday Schedule
Would it be possible to add in a calendar feature to pre-programme upcoming Holidays? E.g. enter a time and date for the holiday to start and for it to end? This would remove the need to remember to switch all heating and hot water to 'Off' as you leave, plus allow for pre-planning and set the holiday parameters (e.g.…
-
Keep history when meter reaches max or new meter is installed/replaced
Frustrating, as Belgium now forces by law to change to a digital meter. It won't be long before more countries will do this, but Tado gives no option to keep the history. A similar situation would be when the gas meter needs replacement due to malfunction or reaches the max digits it can roll to. Support's answer was:…
-
Always On Display Thermostat
The option to have the display shown as always on with further options to also be able to dim or brighten it. The option for it to show current room temperature/set temperature/humidity and also possibly time and date.
-
Proposal for an Affordable Wireless Temperature Sensor
I propose the development of a simplified, cost-effective version of the Wireless Temperature Sensor Add-on. Presently, despite the "Offset" feature, relying on the Smart Radiator Valve as the primary temperature sensor for an area proves to be ineffective. The feature lacks the sophistication required for accurate…
-
Custom Smart Schedule
Hi , I often need additional options depending our home situation. Most of the time I need also a schedule Home but upstairs OFF or Home but upstairs normal schedule. When kids are home sick or we plan to use more the upstairs during the weekend
-
Comfort Zone - Change comfort temperature display
I find 20 degrees too hot for “comfort” and prefer to be able to adjust when it shows as orange and when it’s too cold or hot for ME. Comfort zone is a known Zone, not absolute and different for different people, what is hot for one person might be cold for another. Our comfort temperature changes in response to the…
-
Add Sunrise/Sunset to Graphs
By adding sunrise and sunset to graphs would allow most novice users to understand the natural thermal gain/loss purely from outside temperature and pressure on their homes and differences to different rooms. B)
-
EnergyIQ - Display volume-based monthly forecast
In my opinion, a volume-based metric is more suitable because it is a consistent metric. Volume indication is not subject to change when energy prices/ contracts/ taxes change. Therefore, I suggest showing it alongside the "expected monthly heating cost". Or even better - change it along with the [€ | m3] toggle next to…
-
Integrate with smartthings
we need an official integration. Why would i not want to control some of the best smart elements of my house with my heating??? Makes no sense there is no official integration
-
Energy IQ should also work in the desktop environment
Currently it only works in the app which is strange because usually apps are more restrictive.
-
Tado app for Apple Watch or other watch
It’ll be cool, we had an app for the watch for using on Apple Watch or other Stead of using the HomeKit it will be better than he had an app for the watch is the same way as the iPhone and iPad Don’t want to use HomeKit Can you make one please?
-
Option to show demand temperature set in the schedule on the room temperature display
It would be helpful if there was an option to show the temperature demand from the schedule as a line on the room temperature display. I know that you can see it if you hold your finger on the temperature line of the graph, but it would be much easier to see how the room was performing if the temperature demand was shown…
-
Priority/importance levels.
I'd like some rooms (i.e. bathroom) to stay at some temperature over night but I don't mind if they are slightly more off the set temperature and I don't want boiler to fire up just for that room. It could be heated up when other room (i.e. master bedroom) needs to turn boiler on. Something like the temperature set to 'no…
-
Ability to cool using my smart thermostat?
Hello, I wish the smart thermostat had the ability to cool as well. My geothermal heat pump heats as well as cools. Right now I can only use Tado for heating. It would be great if I could change the mode of the Tado Smart Thermostat to 'cool' in summer and 'heat' in winter. If you need more information about my set up,…