-
Room heat indicators in house overview.
Hi Tado. Can we get the 3 little heat indicator line on all the room tabs in the home overview. It really annoying to have to go in to the room to see if this room is heating or not at that moment.
-
Boiler demand indication on main page
Hi, it would be great to have the three waves or just a simple red dot by the temperature of each room in the main page. Or at least a way to see at glance if any of the room is forcing the boiler to run. Thanks
-
Dew-point prevention = minimum temperature based on humidity
Given a specific temperature the air can hold a certain amount of moisture and when this air hits a cold surface it condenses causing moisture and mold. It would make sense to have an option to enable the that the Humidity reading be used to automatically adjust a minimum temperature for a room to Reduce condensation when…
-
Proposal for an Affordable Wireless Temperature Sensor
I propose the development of a simplified, cost-effective version of the Wireless Temperature Sensor Add-on. Presently, despite the "Offset" feature, relying on the Smart Radiator Valve as the primary temperature sensor for an area proves to be ineffective. The feature lacks the sophistication required for accurate…
-
"summer mode" to keep radiator valves open during summer
The problem is: If I connect all the smart radiator thermostats to my zone controller and I don't want to heat any room (because it is summer now) this results in all the radiators being 'closed' (or 'blocked'). This makes the total central heating system volume smaller (since the radiators are essentially cut off from the…
-
Access to bad connection data and signal strength
To help with placing the internet bridge, It would be helpful if there was an easy way to see when devices (eg radiator thermostats, wireless boiler controller etc) have disconnected from the internet. A list of the times they disconnected/reconnected or even just a total count of the times this happened. Currently to see…
-
Summer Mode: Open/close your windows during Summer notifications
It would be great if during Summer you could get notifications to open your windows when the outside temperature is lower than the indoor. And to close your windows when outside is warmer than inside (or predicted to be soon). This is currently not easy to do with Apple Home automation or Apple Shortcuts so it could be a…
-
Away mode schedule
It would be great if Tado would support an away mode schedule: a schedule that only operates when away mode is triggered, instead of the current single away mode temperature. My use case: due to dynamic energy pricing it is wise to start heating around noon, even if I'm away. But if I'm home in the morning than heating…
-
Multi home
Please will you rewrite the app so that you can use Tado in several homes from the same app using the same names, passwords and login details
-
Improve reception range of the Bridge
The connection with the radiotors is often lost. The Bridge has a short range. A more powefull Bridge or a mesh system would be great
-
Oil Tank Gauge
I have an oil fired combi boiler and your smart heating controls, which work very well. It would be good if i could monitor the level of oil in my tank remotely using the Tado app Maybe some sort of wifi sender on the tank compatible with your hub and app would be good.
-
Heating Bills For Oil Heating Systems Inc Hot Water
Can a modification be made to the usage tracking heating bills to include the option for oil heating systems. Also, there should be a breakdown of usage by hot water which there currently isn’t. If you do enter data from your usage the system does not calculate based on actual usage data and seems to estimate it. This in…
-
Cooling for underfloor water systems
I have "centralized" machine for deliver heating or cooling (according to what it is configured by building manager). I am asking to include some kind of software switch to change between winter and summer mode, just to be able to manage cooling underfloor water system (set 25ºC temperature as a target and achieve it while…
-
Change room colour in app when heating
Can the app be changed to highlight those rooms that are heating
-
Integrate with smartthings
we need an official integration. Why would i not want to control some of the best smart elements of my house with my heating??? Makes no sense there is no official integration
-
Set Max opening on thermostat
I would like to be able to set the max opening to ex. 40% for a thermostat. As it is now, the thermostat often opens 70-100% which results in very high return temperatures on the water. This is a problem because I pay an extra fee if I send 40+ degree hot water back into the public net. It would help if I could control the…
-
Lower hysteresis for underfloor heating
We have Tado controlling our underfloor heating but it has two issues: it's not learning and the hysteresis is too big. If I set the room to 20C then the underfloor heating doesn't come on until the temperature has dropped to 19C. It then runs the boiler until the room hits 20C but the residual heat in the floor keeps the…
-
Manual adjust graph axis
I would like to be able to adjust the axis of the temperature graphs in the Tado app. Currently this goes automatically hence graph axes jump every day and is different for each room. That makes it difficult to compare different days or rooms and makes it difficult to observe how quickly a room heats up or cools down. I…
-
Matter…Thread
a few month later nothing new ? I don’t want to buy dead products…
-
Set hot water temperature through HomeKit
HomeKit integration was a main driver for me to choose tado. I don't like being dependent on cloud services for things that are practically local to my house, so I have configured HomeAssistant to use it through the HomeKit integration. However, after installing it, I found out that there is an important feature that is…
-
Day OFF
The app is missing a key feature for those that have different heating for different days (like weekdays and weekends). For example, I work Mon-Fri, 9am-5pm like a lot of people do. But during annual leave, bank holiday or when off sick, I would like the weekend schedule to follow without reprogramming the whole thing. So…
-
Wireless Temperature Sensor child lock
When linking temperature sensor with tado TRV and child safety lock is enabled on TRV. You can still override and control the TRV by adjusting the temperature from the wireless sensor. Please add the option to enable child lock on the wireless temperature sensor or to the room.
-
Change Zone Controller in time block
Hi there, I'd like to be able to add and remove the Zone Controller from certain rooms in different time blocks. I'd like to have my kids rooms call for heat from the boiler at night but have them not call for heat during the day. I'd still like the rooms to get heat if some other room was calling for heat though so…
-
Landscape Mode for Tado app
Not sure if this is s new idea, as usually a standard option for an app that is a controller. I am new to tado, but invested in home automation and having a wall mounted tablet is pretty popular choice, usually mounted in a landscape orientation which is a must for cctv viewing. 95% off the apps I use for this, screen…
-
Unified schedule view
Please could you consider creating a unified schedule view for all rooms and their schedules to allow for bulk editing and copy/paste.
-
Boost heating - timer
Boost Heating - timer Can you please add a timer for the Boost Heating Timer to the application? example. it's not so cold at night that I want to heat the whole night, the heating is set to off, but I would like to turn on Boost Heating for 30 minutes at three in the morning, for example, and then switch the heating…
-
Ticket system for support
Have searched but only reference I can find is someone who suggested but it was never actioned. Issuing a ticket works well on other sites and enables tracking of a question. I made request for support days ago and received no response. Only means I have of chasing this is repeat the original request. For me the present…
-
Expose the Tado Smart Radiator Thermostats sensitivity setting in the app.
I have multiple Tado products. Also, I have 5 Smart Radiator Thermostats; they only work if the heating is at max and the heating flames are at 3. I spoke to support and they told me that they could make a change in the setting to the Smart Radiator Thermostats and set the sensitivity to low so that when heating is showing…
-
Smaller wireless Thermostat
Your platform desperately needs a smaller wireless Thermostat. I just watched a review of a competitor and they offer one. You need a wireless Thermostat with no controls that simply reports the temperature in a room as your TRV are hopeless at reporting the true temperature This other platform offer a stand alone…
-
Allow the setting of a specific end time when manually overriding.
Dear Everyone, Allow the setting of a specific end time when manually overriding. The way our family uses our house means that having timed heating makes no sense, so we have that effectively disabled by setting one time period for 24 hours at a low temperature (10C). We control individual rooms by overriding this…