-
Push notify users when there is evidence that the boiler/heat source isnt doing its job
It is a common problem for oil fired boilers, particularly those over 10 years old, to be heavily affected by wind speeds near the air intake. A sudden rise in windspeed, occuring within 1 meter of the air intake can cause the boiler's air mass sensor to misread the temperature and volume of air incoming and force the…
-
Individual Room Boost Request
Hey, Would it be possible to implement a solution, where heating for an individual room only could be boosted? Currently, this is missing from the app, as you can only hit a button to boost all rooms at once and then you have to untick the ones that you are not interested in. Which is a bit cumbersome. The only tweak I…
-
Rename Zone Controllers / Wireless Receivers
We should have the ability to rename the wireless receivers and give them proper zone names. I have 3 wireless receivers on my boiler for 3 floors in my house. When I add a new temp sensor or radiator TRV, I should be able to add it to 'downstairs' or 'basement' or 'upstairs'. Not to PR123456789! I installed all three…
-
Hot water control like in V3 - other device control i.e. Apple Home, Google Home or Home Assistant
I have found it impossible to see any control of the hot water in any of the Matter/Thread control systems. It is impossible to add the wireless controller X to any of Apple Home, Google Home or Home Assistant. The only place that hot water can be controlled is through the app, and then only with the facility to set a…
-
Tado Wifi enabled Hot Water Cylinder Temperature Thermostat Display & Controller
As far as I can understand, if you do not have a smart (oil or gas) boiler or a boiler that can separately control and heat only your hot water you are limited to the control and heating of your hot water cylinder by timer schedules only. However a timer schedule cannot detect if you already have enough supply or hot…
-
Energy IQ - Better process for when energy meter is replaced
I recently had to have our smart gas meter replaced, because the existing one became faulty. This meant that my meter reading dropped back to zero when the meter was replaced. When I came to enter a meter reading in Energy IQ, it said I could not enter a number lower than the previous reading. I contacted support, they…
-
Worcester Bosch EMS2
It appears Tado is able to work with older Worcester Bosch Boilers with HT-EMS. Possibly some others Bosch ones with EMS+ ? It will also work on Relay (R01), On/Off Mode, but this will NOT modulate the boiler. All new boiler installations in the uk have to confirm to EnergyPlus Regulations. This means having some of…
-
Stabilizing heat demand pattern for constant set temperature
I live in Scandinavia and often work from home, so I have a consistent heating demand throughout the day. When looking at the temperature/heating graph view, it is clear that the heating demand (and temperature) follows a cyclic pattern with a period of 45min on average. I'd love to post an image but I don't think this…
-
Schedule a boost
I am often away from home. My underfloor heating has a 24 hour thermal lag from 6 degrees to 22 degrees. I regularly forget to preheat it. Can you please add a facility to diarise a temperature boost for one or more rooms?
-
Bespoke Nom Circular Geofence
Allow a non circular Geofence to be plotted. We have a park near our house that would be good to have outside the geo fence, especially when the wife and kids spend a few hours there. If I reduce the current Geofence radius to exclude the park the Tado App says it's too small.
-
Different schedules in X equipment like in the V series
Is there a possibility to have the same configuration related to the schedules like in the V series? Depending on the days: M to F and WE All the days Everyday
-
Consumption graphs: add option to scale the graph from 0
It would be great if there was an option to make the vertical axis of the consumption graphs scale from zero, instead of showing them as a "zoomed in" scale e.g. between 14°C and 22°C or whatever. It's clearer to see patterns and the peaks/troughs are less exaggerated from 0. It's also impossible to compare graphs over…
-
Open Window Detection Accuracy
Hello, I have recently bought tado x and was disappointed by the open window detection. There should be a manual button to say that the window is opened it shouldn't rely only on fixed changes of Humidity and Temperature ( Some spaces takes more time to lower the humidity and doesn't detect the window is opened) when…
-
Internet Bridge local API
It’d be great if it were possible to interact with the Internet Bridge using a local API so that requests don’t need to be made via the internet. Presumably there’s some kind of http server on the device as HomeKit is able to communicate with it locally?
-
Always on display option
Hi just installed my wired v3+ very easy instal and instantly impressed. One suggestion would be to have the option to keep the temp display always on so you don't have to press everytime to view current temp.
-
Diffret status for thermostats that are not linked to a zone
In order to stop a room calling for heat and switching on the boiler (like a toilet, closet etc) you can remove the zone controller for the room. It would be good to acknoladge this on the tile in the app.. currently regardless of the zone set for the room it will say "heating to" i think the rooms that are assigned a zone…
-
The Tado is not Smart Enough
I worked on heating systems before the Internet. Commercial Heating systems used Optimisers. They were quite complex in operation and learned over time. But the controls were simple. It had an outside temperature sensor and an internal temperature sensor as a minimum. You programmed in occupancy times. If the outside…
-
Battery Monitor Improvements
As a suggestion, there needs to be better battery level monitoring\reporting between the Tado application and devices. I have noticed in recent weeks that devices are reporting battery levels as "Good" but then are malfunctioning due to suspected low battery life, which is then confirmed when you re-insert the batteries…
-
Personalised Boost heating
Is there any chance to personalise the boost heating option? Option to program time and temperature for the "Boost heating" would be useful feature
-
New idea: respond to valid user suggestions?
Hey tado development team, being an owner of a software agency myself, it's a huge red flag to me when I see rather trivial user requests and improvements just sitting there for five years (!!!) without an official response. Some guy named "Frank" answered who seemed like a tado rep, but his account is deleted now.…
-
Room heat indicators in house overview.
Hi Tado. Can we get the 3 little heat indicator line on all the room tabs in the home overview. It really annoying to have to go in to the room to see if this room is heating or not at that moment.
-
Boiler demand indication on main page
Hi, it would be great to have the three waves or just a simple red dot by the temperature of each room in the main page. Or at least a way to see at glance if any of the room is forcing the boiler to run. Thanks
-
Dew-point prevention = minimum temperature based on humidity
Given a specific temperature the air can hold a certain amount of moisture and when this air hits a cold surface it condenses causing moisture and mold. It would make sense to have an option to enable the that the Humidity reading be used to automatically adjust a minimum temperature for a room to Reduce condensation when…
-
more than one property
It would be so helpful if one could flip between two different places, each with the Tado system installed, without having to sign out of one account and into another.
-
Access to bad connection data and signal strength
To help with placing the internet bridge, It would be helpful if there was an easy way to see when devices (eg radiator thermostats, wireless boiler controller etc) have disconnected from the internet. A list of the times they disconnected/reconnected or even just a total count of the times this happened. Currently to see…
-
Summer Mode: Open/close your windows during Summer notifications
It would be great if during Summer you could get notifications to open your windows when the outside temperature is lower than the indoor. And to close your windows when outside is warmer than inside (or predicted to be soon). This is currently not easy to do with Apple Home automation or Apple Shortcuts so it could be a…
-
Away mode schedule
It would be great if Tado would support an away mode schedule: a schedule that only operates when away mode is triggered, instead of the current single away mode temperature. My use case: due to dynamic energy pricing it is wise to start heating around noon, even if I'm away. But if I'm home in the morning than heating…
-
Multi home
Please will you rewrite the app so that you can use Tado in several homes from the same app using the same names, passwords and login details
-
Improve reception range of the Bridge
The connection with the radiotors is often lost. The Bridge has a short range. A more powefull Bridge or a mesh system would be great
-
Oil Tank Gauge
I have an oil fired combi boiler and your smart heating controls, which work very well. It would be good if i could monitor the level of oil in my tank remotely using the Tado app Maybe some sort of wifi sender on the tank compatible with your hub and app would be good.