-
Set a delay in closing the smart valves after the "OFF" command to the boiler
When the boiler is sent to OFF, by the thermostat or by the intelligent valves, there is always a post-circulation time foreseen by the various manufacturers to allow the disposal of the residual heat. With Tado the thermostatic valves are closed immediately, generating overpressure in the circuit, and forcing you to leave…
-
History graph (also) in web app
I'd love to have the history graph of devices also in the web app. First of all because I have a larger screen and thereby better readability. Also I (ab)use the web app for another building, as multi-home support is not there.
-
Improved internet bridge / Better range.
I live in a property with 3 floors + a basement and my networking setup is on the top floor Attic and find devices in living room and basement disconnect from the tado bridge. I have Philips hue and everything works flawlessly throughout. The capabilities of the Tado Bridge needs to be improved for longer wireless range or…
-
Boiler external weather sensor + tado
It would be nice for tado to use the boiler external weather sensor if installed while running on opentherm/bus for more accurate heating. Why? Well, weather stations are not all over the place and not so accurate in some zones, so it would help people in remote locations.
-
Blocage de thermostat a distance
Bonjour, ce serait bien de développer un blocage d'un thermostat a distance et que lorsqu'on a des locations, comme ça on gère le chauffage et il n'y a pas d'abus avec des réglages de chauffage a + de 25 Degrés...
-
Heating Off minimum Temp
Hi. I notice if I set my Central Heating schedule to OFF in a time slot (IE: at night) the temperature drops dramatically and it goes very cold with no Antifrost protection. Yet. If I am AWAY from home and the heating goes OFF as I am not present I can set a Minimum temp to heat my home (while I not here as its in AWAY…
-
Hot Water temperature control
See this thread https://community.tado.com/en-gb/discussion/comment/54598#Comment_54598
-
Option to show demand temperature set in the schedule on the room temperature display
It would be helpful if there was an option to show the temperature demand from the schedule as a line on the room temperature display. I know that you can see it if you hold your finger on the temperature line of the graph, but it would be much easier to see how the room was performing if the temperature demand was shown…
-
Commande tadoo pour les poêles à pellets
je voulais juste savoir si vous pouviez mettre vos ingénieurs sur le coup et inventer un tadoo compatible poêle à pellets ça devient important pour nous personne ne commercialise ce système et pour ma part la marque Mcz ne souhaite pas faire évoluer ces anciens poêles en wifi. la télécommande est infrarouge elle prend la…
-
viessman eco mode for DHW
I own an viessmann vitodens B1KF on opentherm protocol apired with tado v3, since i changed to opentherm my eco mod(preheat) option disappeared from both boiler screen and vicare app. its not on viessmann side i ve talked to viessmann and they said this: "Have you spoke to Tado about the DHW temp setting ? The ECO stays On…
-
Calibrate offset of TRVs automatically based on wireless thermostat
Hi Please consider using wireless thermostat as an auto calibration offset tool within a room. Now have TRVs on all radiators. Put wireless thermostat into the area of the room I'd like to adjust the temperature to. Have TRVs in room check their offset against that wireless thermostat and adjust automatically. Have this as…
-
Climate report in Tado Web app
Hi, To me, the availability of the climate report in the web app - app.tado.com - would be a big improvement. Preferably combined with option to export (CSV) and also to compare the reports between different (or similar rooms (between bedrooms fi). This is feature high on my feature list. Greetings Christophe
-
Powered Smart TRVs
Could you introduce AC-powered smart TRVs with a rechargeable battery backup please? Haven't had enough use of the units on battery so far, but want to get away from constantly changing batteries in the household. Take this a step further and have them communicate across the home power cabling to the Internet bridge.
-
Electric towel rail controller
I keep hearing that in the UK, a huge amount of energy is wasted through the inefficient use of electric towel rails. Namely, they are dumb with on/off switches and are not managed alongside the heat output of the main central heating system. Therefore they are left on for long periods. Tado, how about producing an…
-
Graph scale in 1 degree increments
The graph scale is very odd. It is either in units of three or units of six degrees. This makes it very difficult to work out what temperatures the line is reading when it is between the labeled grid lines. It would be much easier to read if the graph scale was simply in units of one degree with ideally subdivisions of…
-
Relais vloerverwarming bij 1 golfje ook volledig open
Blijkens antwoord van Tado is een als relais ingestelde slimme bedrade thermostaat op een Honeywell Zoneklep maar 33pc van de tijd open bij een warmtevraag van een golfje. Dat betekent dat als je temperatuursensor in de kamer met vloerverwarming een warmte vraag naar de ketel stuurt, de zoneklep niet geopend wordt; voor…
-
Multi home
Bought Tado for my Airbnb, love it - bought a 2nd system for my home only to discover no multi home function. Have since read on this forum, and other places, it’s not available so had to return. C’mon Tado… you are not listening to your customers… it’s a pretty basic - and fundamental - requirement!
-
Set A/C mode across schedular
I have an a/c unit that I use to cool the house in the summer and heat in the winter. Using the tado a/c controller, if I set the a/c mode to auto it creates a problem. When a scheduled time block has a lower temperature than the one before it, the a/c will actively start to cool. In the winter this is not a desired…
-
Energy IQ - room heater size
Allow us to enter the size of radiators or UFH systems in rooms to get a better estimate of which rooms actually use the most heat. At the moment I assume the estimates are useless as my 300W towel rail is the highest usage in my home despite having multiple 2kw radiators elsewhere.
-
Change Zone Controller in time block
Hi there, I'd like to be able to add and remove the Zone Controller from certain rooms in different time blocks. I'd like to have my kids rooms call for heat from the boiler at night but have them not call for heat during the day. I'd still like the rooms to get heat if some other room was calling for heat though so…
-
Home Assistant boiler data/control
It would be nice if the data/control to en from the boiler would be integrated in home assistant. This would give a better image of how much gas we are actually using. These info would make nice graphs. Knowledge is power!
-
Landscape Mode for Tado app
Not sure if this is s new idea, as usually a standard option for an app that is a controller. I am new to tado, but invested in home automation and having a wall mounted tablet is pretty popular choice, usually mounted in a landscape orientation which is a must for cctv viewing. 95% off the apps I use for this, screen…
-
App Notification
Add notification on the home tile page to show that tado are performing maintenance or are having issues. Twice this month I can see the internet bridge cannot connect (network tools) and the boiler stays on.
-
fonction iFeel Clim Gree
Bonjour, a quand la fonction iFeel intégrée au tado pour une meilleure efficacité et gestion de nos climes.
-
Hot water tank smart thermostat
I think there is a market to provide a variation on the Smart Thermostat in the form of a unit with a temperature sensor on a cable, to allow the user to install in a thermal water store. This can give the flexibility for hybrid systems that have multiple heat sources for the store such as Solar thermal, biomass and oil or…
-
Connect to enery supplier as a service
It would make it a lot easier and simpler to have a service that connects to the energy suppliers. This would make the the usage and money part of the application a lot more accurate to manage. I have already seen this service offered by some online applications.
-
Standing charge
It would be nice to add the standing charge as a feature.
-
Retaining screw on smart rad valve.
The smart Rad valve needs a retaining screw. This would stop people from accidentally unclipping the head from the screw on base while twisting the top.
-
Custom name per device beside room name
Currently any device has the name of the room and a non descriptive id. To be able to identify for example the device with low battery it is useful to get a notification for a device with clear name (e.g. under window radiator, bedroom 1, bedroom 2)
-
Central Heating On/Off missing feature on Tado app
There is a feature to turn Hot Water on or off in the app but no feature to turn Central Heating on or off. For anyone with a dual heating system for central heating, e.g. an oil fired boiler connected to a Tado receiver plus an alternative heating source, such as a solid fuel boiler, it is essential to turn off the oil…