-
"Lifestyles" - multiple user set memory presets of temperatures for each room
Add a section to the Tado app for "Lifestyles" (or similar name to avoid copying Honeywell Hometronic/ Evohome/ Evotouch) Multiple user set presets so a one button push in the app will activate or deactivate a memory programme with user pre-determined temperatures for each room. i.e. Lounge 22 deg, Kitchen 21 deg, Bedroom…
-
Support 8°C mode on Toshiba AC heatpump
Today I can either control the temp fro. 17°C and upwards or I must shut the AC off. If I shut the AC off then I risk that the water can frezze inside my cabin. Most AC support an 8 °C mode to ensure that this will not happen. I can't find a way to do this in the TADO app
-
Large House Capability
I have a new Tado system fitted to an old oil boiler and I am mostly loving it. The issue I have is thick walls and scalability. I have maxed out devices so had to change back to regular TRVs in some rooms and I have maxed out on zone controllers. The bridge can never see all TRVs or Wireless Temperature Sensors (WTS) at…
-
EnergyIQ compare to same month last year not previous month
The energyIQ graph compare the last month with the current month. This doesn’t make much sense because any changes are likely to be seasonal and weather dependent rather than as a result of any actions. It helps to reduce energy usage and costs if we are comparing year on year consumption
-
standard temperature: lower
The standard temperature of TADO is 21 degree C.. If that is true, isn't it a better idea to lower this standard temperature on behalf of the climatecrisis and, recently, saving costs? For example lower it to 19 or even lower temperature. If someone wants to heat more, be free with TADO to do that.
-
Backup settings
Problem - other members of family mess up carefully programmed heating schedule. Solution - access rights of other users limited or way to restore backup settings to revert to original schedule.
-
Hot water not working? You need the room temperature sensor
I have just set up a tado system for my elderly mother. She has only 4 radiators and a hot water tank in a Y-plan configuration. I put smart TRVs on the radiators and they were working to plan, but the hot water did not work. The wifi receiver seemed to be refusing to configure to the Y-plan, reverting constantly to a…
-
Merged: Setting the boiler's heating water temperature via the app (just like hot water)
This discussion has been merged.
-
Cleaning Mode
Hi, I was thinking that it would be a good idea to have a cleaning mode toggle in the app that would disable all thermostat radiator valves (or enable the child locks) in 1 go so that temps are not changed during cleaning. Thanks
-
Combine "Smart AC control V3+" with other Tado products
When you allready have a livingroom with several Tado products like the "Starter Kit - Wireless Smart Thermostat V3+" and "Smart Radiator Thermostat V3+", but in the same room also an Airconditioning system, let this all work together. There is allready the product, the "Smart AC control V3+", but i've learned that these…
-
More devices to have a smart home, such as smart sockets
It would be nice to have a single app to control everything, coming from a single brand. instead of buying smart sockets from another brand, or buying another bridge device (e.g.: Philips Hue, or Bosch), it would be nice if Tado also provided these devices. I'd happily buy a smart socket or lamp switches from Tado for…
-
Switch off bridge LEDs/Extinction des LEDs du bridge
I would liké to Switch off LEDs on bridge. Brigthness IS toi high and it could save energy. Bonjour, J'aimerais pouvoir éteindre les LED du bridge qui éclairent tout mon salon et ça ferait aussi une économie d'énergie. Merci
-
Wireless thermostat always on display
I'd like the wireless thermostat to constantly display the room temperature
-
Hybrid Heat Pump support [Atlantic Aurea 5 R32]
This heatpump comes with the plugwise Anna thermostat using the opentherm protocol to control most combi-boilers, so they control the heatpump and the combi-boiler, but one must remove the Tado thermostat. If plugwise can control the hybrid system, it should be trivial for tado to do the same thing. I would like to remove…
-
Honour Schedule While Offline
My Tado keeps disconnecting from the internet (the only device on my network with this problem). This means the schedule to power heat for 0630-0700 doesn't come on, meaning no hot water for a shower! 🥶 Could the schedule be pushed locally onto devices which are connected to power, but disconnected from internet?
-
Adding the "Disease" scheme
I am asking for the option of setting one "button" of the sickness scheme, when the heating of rooms that are switched off according to the plan needs to be urgently addressed, because normally during the day there is no need for heating in these rooms. But in the case of Home office, illness, etc., the heating scheme in…
-
Range Extender
We live in a 4 stories house with a lot of concrete. The Bridge is only able to reach 3 stories, on the 4 floor does the signal often go away and the device is offline.
-
Exterior weather monitor
I would like to have my own external weather monitor that could feed directly into tado to give a more accurate picture. Along with more interesting stats - probably.
-
2 Bridges
Can you have 2 bridges. I will have 2 zones can each one connect to its own bridge. I have a big house and connection is unreliable with one bridge. Thanks John
-
Longer graphs?
1) Show all devices on a single page in a graph 2) Show the graph as above but showing 1 week, 1 month etc intervals? 3) is there an external Tado device that can be installed to indicate the true outside temperature/humidity? 4) Can the graphs be printed?
-
Select and copy serial number to clipboard
When contacting technical support they request the serial number of the device. You have to manually type it in when you should be able to long press and copy to clipboard
-
EnergyIQ bad UI design for viewing history
Hi, Thanks for the latest EnergyIQ update: >> Energy IQ has been updated, and now you can view your historical heating consumption all the way back to when you first installed tado°. To check your consumption from a previous period, open the Energy IQ skill and select the desired month from the dropdown menu at the top of…
-
Fuel bill entry
A lot of people who live in rural areas may not have piped gas to their home. Those of us who are either on LPG or Oil get irregular deliveries of fuel. It would be great to be able to simplify the energy bill entry as it could be anything from three to five months between deliveries rather than monthly, quarterly or bi…
-
[released in beta] Yearly Energy Data
Energy IQ is a good start and enables the user to see costs of current months heating cost compared to last months. Can you add a feature that allows user to look at last years complete monthly data and compare it with current year to date. Users can then see if changes to their system have made a difference to running…
-
Quick offset for summer & winter
Like most my thermostat is downstairs near my boiler, I often need to change my +/- offsets as my upstairs bedrooms are warmer in the spring / summer and cooler in the autumn/ winter, would be nice for an auto correction around those times of year for this.
-
Zones for boost heating
It would be useful to be allowed to create internal zones in regards to boost button, for example only to heat bathrooms or only to boost rooms on ground floor. I live in 2 storey house with only 1 heating zone so when I press boost all house will be heated up, if we could only create up to 5 zones and add rooms of our…
-
Low battery heating demand should show on Care and Protect
When the low battery condition is triggered, the "care and protect" function says that the heating is not on, but it clearly is. The care and protect function should show, preferably, a message saying "heating demand due to freeze protection for room/valve change battery", or even just "heating 100% room".
-
Low Battery Heating Command should take outside temperature into consideration
In a low battery condition, the smart radiator valve seems to command heating, presumably to avoid potential freezing when unattended, however, this is unnecessary when outside temperatures are high (like today!) - the defect/feature request is to disable this behaviour when the outside temperature is above e.g. 5C I kind…
-
Stats in the web browser + Fix weather on off toggle button
Hi, Can we have the stats available via the web interface? Also on the stats in the Android App the Outside Weather toggle button is the wrong way round to the Heating on and Humidity button, if you toggle them on whey go grey yet grey on the weather button turns the weather off.
-
max temp
I have people living at my house and they ALWAYS put the temp on max - please add feature to set max possible temp to fx. 22 degrees or so...