-
Add option to reboot devices overnight
To improve resiliency, add an option to reboot all of the devices every night. Either the whole system or on a per device basis.
-
Add a text field on devices to show their location in the room.
I have three radiators in a room. It isn’t easy to locate a TRV which needs resetting. Have to use the Hi button and work out which one isn’t responding. Easy solved by adding a text field in the devices summary screen. It could say “near door”, “behind settee” and “near hifi”.
-
Either block or support being a member of more than one Tado home
I accepted a membership request from my son’s Tado and it wiped my App configuration. Was a nightmare to get sorted. Either block accepting a request if you already have a membership or support multiple homes in the app properly!
-
Basic Wired Stat
Hi, I have a home with underfloor heating and 13 zones. I wish to upgrade. I use TADO at another property and it is great. However, at around 100 pound for a stat it is "too expensive and too smart" to buy 13 of them. I believe there is logic in a more basic phone connected wired stat. There is no need for humidity,…
-
Day Off
I would like a day off button with a adjustable end time. This would then run the sat-sun schedule as sometime I have a day off in the week.
-
Control even and odd weeks respectively
I'm wondering, could it be possible to control schedules for odd and even weeks in the application? Biweekly (even weeks) my two children stays at my place, and biweekly (odd weeks) they stay with their mother. Quite normal nowadays which is why I think it makes good sense to have the option to lower the temperature in the…
-
Dynamic schedule - Auto Sleep Wake-up
Make Tado intelligent by integrating it with sleep sensors and or your wake-up alarm. In that way you could have a dynamic schedule (instead of a fixed one) that would activate when certain people are in the house but sleeping or when those persons are scheduled to wake-up based on their wake-up alarm set on their phone…
-
All thermostats history on one graph
It is very difficult to analyze the operation of the entire heating system. For example, it is difficult to see the effect of a thermostat in one room on the temperature in another. It is also difficult to say how often the heating request is sent because each thermostat sends it independently. It would be very helpful to…
-
New hardware idea - Zone Controller and Electrical Heat Switch
Just i read Tado best alternative, Drayton website and i found that they maked some new devices: Zone Controller: https://www.draytoncontrols.co.uk/products/Smart-Heating/Wiser/wiser-underfloor-heating-controller Electrical Heat Switch:…
-
Allow changing temperature if one device in a group of two or more loses connectivity
I initially reported this as a bug to online support, then they told me it works by design and should bring it up here instead. Which doesn't make sense to me but still, they didn't leave me with any options. It appears that if one device in a group is offline, you can't control any of the remaining ones through the UI.…
-
It should be possbile to select the wanted fan speed at Homekit, IFTTT and other services.
I just bought a new Tado Smart AC Control V3+ to control my Mitsubishi Electric FH35 heat pump, based on the measrument from external Netatmo- temperature sensor. First I integrated Tado to Apple Homekit, but when I created on automation (such as "if temperature is below 22c, set Tado for Heat mode"), I noticed that I…
-
Alternative scenario
Now first time using Tado during the holidays I am missing the option of an alternative scenario. On home screen have the option to select / create one e.g. Holiday (or select Main as default) To create either you can first make a copy of Main (so you only need to change some blocks of some rooms) or start with an empty…
-
widget for geofencing
dear community, it would be nice to add a widget to the app to provide the possibility to manually toggle the away/home from the phone desktop
-
Leave valve open when batteries low
When the batteries go flat, I have found that the heating keeps trying to heat that room, but with the valve closed it won't, so the system either needs to turn that room off or personally I'd rather it leave the valve open so it can heat the room, with the rest of the house.
-
graph
The Graphs on the app should also be posible to view in a browser. This with the option to download "raw" data, like in a CSV. Thank you
-
Change comfort scale
I find 18C comfortable, yet Tado tells me that I’m cold (even 19.5C is considered cold, whereas it’s uncomfortably warm for me). I’d like to be able to change the comfort scale, so I’m not prompted to “put on a jumper”, “snuggle under a blanket”, or “turn the heating up”. When we’re meant to be saving energy and resources,…
-
Time display on temperature graphs
When you display the temperature graph from the tado app (iOS) you can touch the display to show the actual temperature. But the time is missing on the pop-up. Can this be included?
-
Full Air-conditioning Control
I have a house in France that I rent out with 5 air Mitsubishi Conditioning units. These units are inverter units so can perform the following tasks: cool,heat,dehumidify, fan, the IR controllers interface looks to of been created by the same guy that invented scientific calculators. Great if you know what you are doing…
-
Window (No.) open detected
Hi. Hope all is well. Window open dedicated does not tell me which window is open and sometime I am notified even though all my windows are closed. This tells me that draught is somewhat coming in but I don’t know from which window. It would be really helpful to be able to identify which window is open, this is so that one…
-
Air Source Heat Pumps
I have just replaced my Tado controlled gas boiler with a Mitsubishi Air Source Heat Pump. I emailed Tado and enquired if they had any experience in using Tado in conjunction with such a device. The reply came back that I should put my enquiry here. Perhaps Christmas has come early! It doesn't seem the logical place to me…
-
Allow output of temperature,
Hello, I would like to record the temperature every time it changed to my spreadsheet, currently I can do this by creating an individual recipe for every temperature rise and every temperature fall, obviously this would take a long a time. Would it be possible to create a query which simply reports the temp, or a trigger…
-
Maximum heating setting-lock
So many people have younger adults who may want to set the heating at silly temperatures. So my idea is a max temp setting-which can be controlled by an admin for the house? I think this is a good thing for many. Also avoids errors if knocking to 23 instead of 21 for example.
-
Include heating graphs in features without having to pay extra
I have only just purchased and installed the Tado system in my home, at huge cost with 12 TRV's to try and get even heating and where I want it. To check its working I really want to see what the temperature has been over a period of time to see how well its working, and when the boiler has been on and off, to see if I…
-
connect app to your gas and electric provider
Wouldn't it be great if there was some way to connect your app with your electric and gas provider to get an accurate idea of not only consumption but cost. I realise that at this time you have to enter your gas usage manually but if the it was linked or even if you could add the gas price to the app this would be more…
-
Return temperature sensor (on radiator) connected with the thermostat on the inlet
Tado should produce a temperature sensor that can be mounted on the return pipe from the radiator. The temperature measurement must then be connected via the hub to the thermostat on the radiator inlet, so that the thermostat can turn off the heat if the return temperature becomes too high. In the setting of the…
-
Meter Reading in Kwh
It appears you can record your tariff in kwh and set Kwh as your preferred measurement, but the add reading menu only states m2. Either this kwh needs to be added as a meter reading option or if the value entered is whatever you set your preferred measurement to, then the reference to m2 in the add meter reading ui needs…
-
Multiple schedules in one room
It would be great to be able to generate different schedules for different devices in the same Room. I have an UFH with wired thermostat and a radiator with RTV in the same physical room. Weekday mornings heat is only needed for one hour, so UFH better stays off. The radiator would be much better controlled by a wall…
-
Schedule a one-time time slot, to overrule the week schedule
I would like to schedule a one-time time slot. For instance: in my home office, temperature is low by default, because I work a lot outdoors. But tomorrow from 10am - 12pm I have a meeting, so then I want it to be warm. So default temperature is low, set in my Smart Schedule. But I'd also like to tell the app 'make sure…
-
Irresponsive/malfunctioning unit alert
Hi! I had a couple of instances where one of the heating units in the apartment were irresponsive, due to something bouncing / slightly misplacing the Tado regulator. The issue, once discovered was quite easy to fix (by recalibrating the regulator), but it was not obvious to catch. I was thinking it should be relatively…
-
Fireplace detection
During winter season I regularly use my fireplace, the increasing temperature will soon enough shut off my ac unit (heating). So far so good. I usually set he ac unit in fan mode to help distribute the heat. I’ve tried to automate this without much success. I see no support for this in the Tado app. Since HomeKit does not…