-
Fireplace detection
During winter season I regularly use my fireplace, the increasing temperature will soon enough shut off my ac unit (heating). So far so good. I usually set he ac unit in fan mode to help distribute the heat. I’ve tried to automate this without much success. I see no support for this in the Tado app. Since HomeKit does not…
-
Set AC temperature by sensor
There should be a way for Tado to turn ON and OFF the AC to get the given room-temperature choosen in the app (read by the tado sensor). I.E: The AC might have a minimum heat of 17 degrees, but it should be posible for Tado to sett 13 degrees and then have the panel switch the AC OFF at aproximatly 13.5 and then ON again…
-
Add signal strength indicator to help positioning the gateway
New (quite happy) user here; the radiator thermostat that is the furthest away from the gateway started to drop out and i believe that providing some signal strength indication (or even graphs !) would help placing / optimizing the gateway position and orientation by providing feedback to the adjustments.
-
Add new "Consumption" menu to web interface
Hello there, Please add new "Energy IQ" Consumption menu to web interface. It only available on the app (i dont know, why...) It more comfortable that see it in web interface
-
Add WiFi support to Extension kit to get rid of bridge
Seems a logical option for those folk who have a full Tado installation with HW control. Add WiFi support into the Extension kit since it's mains powered. This would remove the need for (and failure risk of) a separate bridge This would almost certainly need to also include an upgrade to mesh capability as many extension…
-
Auto switch off Airconditioner when temperature falls below threshold temp
Heating with an airconditioner is many times more efficient than with a fossil/solid fuel burning solution. However this efficiency is greatly reduced when the outside temperature falls below 40 degrees F or 5 degrees C as the outside module of the airconditioner starts to freeze and needs to use additional energy to thaw…
-
Aanpassen aanvoertemperatuur CV
Graag een functie toevoegen om zelf de aanvoertemperatuur voor de CV in te kunnen stellen. Nu moet dat heel omslachtig en tijdrovend via de helpdesk. Ik denk dat iedereen er bij gebaat is, wanneer de klant dit zelf kan aanpassen.
-
Bring 0.1 temp increments back.
After years of making sufficient improvements to the app, Tado have in my opinion really ruined the rentals settings in the app. Instead of having 0.1 increments we now have 0.5 when manually Channing the temperature. Why why why. There are so many examples of how to do this easily.
-
switching between accounts
It could be common that families have more than one home (a main one and the second by the sea or in the mountains) then they need to create more than one account to manage different homes thermostats. I can understand, but not completely, your choice to separate account for each home but you have to facilitate the users…
-
Reorder scene items
It would be great to be able to reorder the commands in a scene list. Presently items are added to the bottom of the list. This means that you cannot insert a new instruction somewhere else in the list and have to start over if you want to make a change. It would be great to be able to drag and drop items within the list
-
Bridge connectivity
As with many people on the forum, I have had connectivity issues in a house with the router and bridge at one end of the house. In the end, I had to return some sensors back to a non TADO alternative. I have just found that a tp-link powerline adaptor AV 1000, would allow the bridge to be connected remotely to the router.…
-
A manually set temperature overrides the schedule. Let us know here if you don’t want this
I raised the following with Tado: If you indicate by geofencing that you are not at home, the heating will stop according to schedule, but not by manual settings. In other words, if you manually set the heating higher than according to the schedule and then leave, the heating will remain on. I find this very impractical…
-
Priority order that rooms heat up in
I think it would be a good idea to be able to set a priority of what order the rooms in my house heat up in as this would help when heading home as I would like lounge etc heated up to temp first but not so fussed about bedrooms and bathrooms. This would help to save money as heating system could come on later
-
"Boiler-on" indicator on Home Screen
It would be helpful to have an easy way to tell if the boiler is being called upon or not - as it can affect radiators that do not behave independently and also help in understanding the general picture when it comes to fuel consumption. Currently, the only way to do this is to review each and every tile to see if any of…
-
Alternate heat source
Would it be possible to have a button for alternate heat source. This would allow tado to work as normal but not trigger the boiler to come on. I have a back boiler that is used during the winter that heats the house and water so the boiler is not required in order to have the radiators open I currently leave tado to do…
-
Apple Watch native app
With useful canned responses/quick links eg message “you seem to have left home.. [switch to Away] [dismiss] Single click. Very cool Or at a glance small tiles showing which rooms currently being heated
-
Extend your gateway coverage
For those who are desperately asking Tado for years to add some range extender option to their product line-up, what follows may be worth reading :-) Recently, as I was in the process of adding TRV's in rooms located in my attic, I faced the "good old" historical coverage issue of Tado's gateway. The big issue is the fact…
-
Wasting battery power
Why do the valves work totally independently of the main start and stop process? What I mean is, why when the pump is about to stop do the valves close? They then may need to reopen again when the pump starts. If the valve was left open it would be ready when the pump restarts. If that valve doesn't need to be open it can…
-
Dazzle mode from Homekit please
When changed manually from Apple Home app, and from Home automations. Would provide extra confidence and visual clues when there are adjustments.
-
Position of valve on smart radiator
It would be nice to understand for each smart radiator what is the position of the valve. In the same way as we know how much heating is being asked from boiler, this info would help to understand better behavior of the system.
-
Ploegenschema’s toevoegen aan slim schema
Graag een ploegenschema voorzien in de kalender in plaats van enkel een dagelijks/wekelijks. Graag twee-wekelijks, drie-wekelijks of herhalend om de x aantal dagen.
-
Real Support
Your e-mail/chat only support service with a promise to get back within 24 hours is rubbish. I have been a TADO user for years and have been happy until moving home and now cant use my new system. I am currently applying to my Credit Card company to have the £1500 I just spent returned. This is because my questions are not…
-
Overzicht sherm en kamer temperatuut
Op het overzicht scerm staat staat de huidige temp in grote cijfers aangeven, als je in een kamer kijkt staat deze temp. In kleine cijfers, het is veel makkelijker (leesbaarder) om in beide gevaal de huidigeen de ingestelde temp in grote cijfers aan te geven
-
Extensie voor internet bridge
Gelieve een “access point” / “repeater” functie te bouwen van jullie bestaande internet bridge. Mijn woning heeft 2 volwaardige verdiepingen en het bereik van de huidige internet bridge is niet voldoende. Een bijkomende bridge (per verdieping) lijkt mij geen onmogelijke opdracht. Jullie hebben reeds de hardware. Zet daar…
-
one time heating for short time
Hi, I have idea if is it possible to add in your app one time heating time. For example if I have heating plan in smart schedule, but something change in one day and I know it need heating 3 hours early, but I don't want to change the plan.
-
Add top and bottom holes to the wall plate of the smart thermostat
I have seen that some wall boxes are rotated by 90 degrees, leaving the screws that hold the wall plate on the top and bottom, instead of right and left. To fix this I had to drill two holes in the wall plate of the smart thermostat to be able to screw it to the wall box. Improvements suggested: 1. Add top and bottom slots…
-
Artificial intelligence heating to desired temp
When I set the heating I select a room and temperature. Instead, could the app calculate how long it ‘normally’ takes to heat the room to that temp. Could the app then initiate heating, to the temp at the desired time. This is something I try to calculate but I think some development and an intelligent app could do it…
-
[Feature Request] Notify when room temperature drops below set room temperature
I have noticed few times that heating won’t start when water pressure is the boiler is low, it will be useful to know that there is an issue with heating and not wait for couples of hours to realise it.
-
Knippen en plakken airco thermostaat
Heel fijn dat je kunt plakken en knippen in de thermostaten en radiatorknop, maar dit kan in de airco thermostaat nog steeds niet.
-
Humidity indicator
Could have added humidity level in HomeKit nearby temperature like little ⭕️