-
Alternative Schedule (for working from home as an example)
I've been using Tado successfully for several years, across houses and love it. I've got a 2 Thermostats, 9 TRVs and an extension unit for my hot water cylinder. Obviously I have a long embedded schedule setup and working well for my current house. I've recently updated it with the second Thermostat powering an external…
-
Regulation improvement
The target temperature given to the boiler is rounded because of boiler limitation. In some situations, the the room never reach the target temperature because the regulation compensate in the wrong direction. For example, if I set 20,4°C on the thermostat, the target on the boiler is rounded to 20°C. Thus, if the room…
-
Rest warmte gebruiken op andere kamer
Ik zou graag de functie willen. Als mijn woonkamer warm is. Ik de radiator op mijn slaapkamer kan open zetten. Zonder dat de cv ketel aangaat. Zodat de rest warmte mijn slaapkamer opwarmt. Mijn slaapkamer hoeft niet zowarm, maar als ik dit nu doet gaat ook de cv ketel weer aan. Wat denken jullie hiervan
-
Downloadable data
I love the Tado temperature/humidity graphs. However, the ability to only see the data on a day by day basis is restricting. The ability to download your data for use in a spreadsheet (in the same way that Fitbit does with its far more complicated data set) would be extremely useful. For example, it would be possible to…
-
Combined bridge power/ethernet wire
The included 30 cm power wire and ethernet cable contradict the advice that optimal positioning of the bridge should be vertical and not directly behind the router. It is very hard to get the bridge into a vertical position and on the wall while not being very close to the router. Tado also suggest the use of powerline…
-
Bridge Attachment kit
The tiny size of the Tado Bridge is a big plus point. However, I find that the double-sided sticky pads come unstuck every few days. I am therefore having to construct my own holder, or will have to use a very strong glue to permanently attach the device. A tab above and below with a screw hold would work better.
-
WIFI 6 Mesh Wifi or Thread IPv6 to solve range issues
Those with large houses or thick stone walls, will have undoubtedly come across range issues with Tado. They are also increasingly likely to have resolved these issues with mesh WIFI or powerline WIFI adaptors. WIFI 6 routers are not yet commonplace, but offer a low energy solution for TRVs and thermostats. Similarly…
-
Current Temperature Font
Hi, So even though my eye sight isn’t what it used to be, the font size for current temperature is tiny, it really does need to be made bigger and should be a pretty straightforward UI fix.
-
Repeater display on app . . .
From time to time my system's Wireless Receiver loses contact with the Internet Bridge (slow blinking wireless and ! LEDs.) Generally this corrects itself although sometimes I've had to re-pair the units. Last night something unusual happened, no loss of connection but a TRV calling for heat and opening but not triggering…
-
Temperature labels
I think it would be useful to have an intermediary step in setting the schedules, one whereby I can create a handful of labelled temperatures and then assign them, or use manual temperatures, to blocks of time in the schedule. For instance, I create ‘in-use’ ‘unused’ ‘walk through’ and ‘bathrooms’ labels in temperature…
-
Sensor Map in app to support internet bridge location.
Provide visualisation in app with internet bridge in middle of map and all connected devices surrounding it showing the current state RSSI value. This will support me in understanding how to change location of internet bridge if I know that one sensor location has -30dbm, another -70dbm another -80dbm then I no longer have…
-
Multiple Wireless Receivers on one Tado account
I think it would be great to have multiple wireless receivers on one Tado account so for people with more than one zone or more than one boiler can have all the devices on one account rather than split them on two different accounts!
-
Additional physical sensors (presence, doors closed) for more targeted routines
Hi! It would be great to have couple of additional sensor types to allow more customised routines: - presence/motion sensor - door/window open sensor These sensors could be additional conditions to the routines, e.g.: - heat bathroom to 23 degrees only when the door is closed - heat Office to 21 degrees Monday-Friday 8-18…
-
Badly designed system
I'm kind of annoyed that I even need to post this here so apologies for the tone but I've repeatedly asked by customer support to do it even though I think what I describe below as a bug or at the very least, a highly flawed design. I do not think such issues should be dealt with via an 'ideas and suggestions' category in…
-
Battery Warning TRV
Can you please provide a warning when battery low. At present a warning is given and TRV has already failed. Please give a warning earlier before the trv fails
-
Tado IFTTT when on/off detected
When any radiator device is switch on or off I'd like IFTTT to receive that information. Many other smart devices already have this feature and for people like myself who have built a smart home hub, the ability to ping/check the status of each radiator would be incredibly useful. Right now my tado section in my own hub…
-
Auto return to room schedule when temp has been manually set
The schedules are real flexible but sometimes you need to boost the temp. This you can do easily via the app or stat. What would be usefully would be able to select return to to normal automatic schedule on the next timed change to the room temp. We have had a number of occasions where someone felt cold tweaked the stat or…
-
Please consider Tado app return to 0.1° granularity
I find the app manual temperature now of 0.5c increments to course. please consider returning the 0.1c old variation which was much better if for nothing else for saving gas and the planet if nothing else.
-
Mechanical Ventilation System
Hello everybody I‘m using your thermostat for a floor heating system and it works very well. What I miss is to tell the system that there is a mechanical ventilation system. Will there be an update to configure such a ventilation system, so I don’t get a notification to open a window? Best
-
Apple Watch App
Please make an Apple Watch App!
-
Temporary off with timer
The current whole-house on/off feature is manually off, then manually on. It would be helpful to set a timer, so that we can turn the whole system off for a certain amount of time only.
-
Change currency on estimated energy report
Currently the beta “estimated energy report” appears to be fixed as EUR currency. This should be configurable so users can select their home currency e.g GBP
-
Add hot water boost - instead of manual control under hot water settings
In order to boost the hot water for a time period (eg 1 hour) you have to go into Rooms & devices, settings, hot water and then finally access the manual control. It would be a lot easier and more user-friendly and intuitive if there was a simple boost button under Hot water icon. In case anyone is following all the…
-
App Tile Swipe functionality
I would like to suggest adding tile swipe functionality. This would be to enable a swipe to the next device/thermostat after selection from the main dashboard. The app currently requires you to exit and select to enter the settings for another device. Retaining current functionality whilst adding the swipe to the next…
-
Radiator Thermostat Hardware Lock
My bedrooms are heated via district heating, so I do not have a central thermostat that turns on or off the heating. My house can be booked by AirBnb guests. When I have guests, I am not at home. I have already noticed that detaching the radiator thermostat from its mount, is very easy to do. I would like to have an…
-
Tado app to show total amount of heating hours used for a month
This seems like a no brainer to add to the app. The info is already there if you look at the day-by-graph but it's hard work to add this up manually.
-
Heating Activity - Total Heating Time is wrong
If a room that is not assigned to a zone controller is the only room 'on', then Care & Protect counts this as Heating Activity even though the boiler is off. This is incorrect, and means the Heating Activity is inaccurate if there are any independent rooms set up. Please change Heating Activity to only include time when…
-
Temperature measuring device
For rooms where you have multiple devices such as two radiators with TRV’s or also a controller it would be great if you could select more than one device or allow Tado to use the average temperature across multiple devices in that room. In my living room, I have two radiators. Selecting one as the primary measuring device…
-
Notification when manual mode
I think a notification when somebody in the family select it woulf really help. Aldo considering thag Alexa and Google somtimes misunderstand pur command and change temperature without our pur will.
-
Open Window Reminder Notification
How often do you forget to close a window? It happens constantly to me that I open a window and totally forget about it. Tado of course detects the open window and pauses heating for 15 minutes. But after the timer expires, Tado resumes heating despite the window still being open. Therefore, I would suggest to add a…