-
A manually set temperature overrides the schedule. Let us know here if you don’t want this
I raised the following with Tado: If you indicate by geofencing that you are not at home, the heating will stop according to schedule, but not by manual settings. In other words, if you manually set the heating higher than according to the schedule and then leave, the heating will remain on. I find this very impractical…
-
Relative units in Energy IQ setup
In residential buildings there are still some individual radiator meters. In the Energy IQ setup one can only give kWh or m3 as unit but this is only available on a building level. Can something be done to use individual meter readings from Techem meters for example?
-
UK Customer Service Telephone Number
Currently no UK customer service telephone number is available. This is not good for Elderly people who are less technically endowed then other generations and when they have a fault just want to speak to someone to get the fault rectified especially in the Middle of a UK winter. It causes allot of anxiety. Given the…
-
Need to add an additional Heating Unit in the Energy IQ feature (Cubit Feet) for the UK
I'd like to request that the Tado Development team add an Heating Unit of Cubic Feet (ft3) in the Energy IQ part of the app. At the moment, there is only m3 (cubic metres) and Kwh there at the moment, and a huge number (Millions) of UK homes have gas meters with cubic feet callibration not m3 or kwh. Without having Cubic…
-
Settings after signal loss and auto-reconnect
Regarding the wireless receiver of the central heating, it is undesirable for it to remain on when there is no signal. I have returned several times to a home with tropical temperatures after the signal was lossed for unknown reason (so far) and the heater remains (last setting before disconnection). Can't this be set to…
-
"Summer/Cooling mode" for wall thermostat
Hi there, I have an underfloor heating with a cooling function. In summer, cool water can run through the floor to cool the room. For that I currently need to set the temperature to max (25°C) to keep the thermostats open. If the room temperature would rise above 25°C the thermostats would close and prohibit a cooling…
-
Data export
Please allow download of chart data for each room. This would be most useful as a CSV file. Data available should include date/time, actual room temp, demand temp (what the heating has been set to), humidity, open window detection, etc. I would like to be able to analyse my own data, and be able to make easier comparisons…
-
Switching between Zone Controller and No Zone Controller/ Universal Switch
Please could you incorporate a universal switch for Zone Controller, so that the user could switch all his TRVs to "No zone controller" and back to the specific Zone Controller with a single toggle button? Currently, it's really annoying having to go to Settings -- Rooms & Devices -- The name of a TRV -- scroll to the very…
-
Radiator Fans
Hi Could you look at the possibility of add on-product such as a radiator fan kit... fans that clip under the radiator, controlled by the Tado valve, so when valve turns on, the fans help circulate the air around the radiator?... this would make a great add-on to Tado and help make it stand out from the other smart valve…
-
Set a manual time limit on Manual Away Mode to go back to auto.
Set a manual time limit on Manual Away Mode to go back to auto similar to the manual timer mode on the TRVs/Thermostats.
-
Open mode
I suggest to incorporate to smart radiator thermostat the possibility of allowing the valve to remain open, even if it exceeds 25 degrees
-
Matter…Thread
a few month later nothing new ? I don’t want to buy dead products…
-
Wireless Internet Bridge
This is a super simple idea, and franky it surprises me you haven't done this yet (or have you?), but wouldn't it make sense to have an alternative do the Internet bridge with a wireless antena? I have my home fairly well covered with a mesh wireless connection, but the fact that you need to have all radiators connected…
-
Monitoraggio finestre aperte
In Tado non esiste un report relativo al monitoraggio delle finestre aperte durante la giornata. Propongo, se possibile e non troppo oneroso, di inserire questa nuova funzionalità che ci dica: - tutte le stanze in cui si è verificato il rilevamento con gli orari - quante volte in quella stanza si è verificato - le…
-
Show end time while editing the duration of a heating override in the tado (web)app
When temporarily overriding the heating schema (e.g. I temporarily want to heat up a specific room), I can choose for how much time I want this override. However, I typically want to directly see at what time this override will stop, not only how long it takes. So basically, when setting the duration of the override, it…
-
Battery Warning TRV
Can you please provide a warning when battery low. At present a warning is given and TRV has already failed. Please give a warning earlier before the trv fails
-
thermostat mode
Hello, the choice to eliminate the possibility of setting the operating mode on the thermostat (legacy mode) to turn off the air conditioner "manually" is wrong; it was a very useful option.
-
Can Geofencing button be put higher in the home screen
I use my geofencing button very often in order to switch manually from "home" to "away". I would like to have this button on top. After all, it over-rules all other buttons Can this button be added to the function button "Reorder Rooms". This way, I can put the button where I want it Thanks
-
Firmware update to include EMS2 support
Having upgraded my boiler to a greenstar 4000 30kW, I am disappointed to find out that tado cannot connect digitally, only via relay. There will be a lot of customers facing the same issue and this should be set as a priority to be resolved as I can’t imagine a firmware update to include the new language being too…
-
add LPG to Fuel type
would i be possible to add LPG to Heating Type with the calculations to work with graphed data to reflect price and KWH for unmetered connections
-
Default for adjusting a TRV should be “until next change” or at least set as default
I quite often increase the heating in the front room using the TRV. That seems to set the temperature “until you resume the schedule” whereas if you use the app the default is “until next change”. This has resulted in me leaving the heating set on 20oC overnight a few times. Is there a way to change the default setting? If…
-
Temperature Display
Hi When you blink the display from the app can it display the current temperature rather than a pointless message. Regards John
-
Global boiler override schedule
My system gets turned on a lot as different rooms heat up at different rates. I’d like to have a global boiler override schedule so I can ensure it’s always off at certain times (including heating and hot water) rather than having to try and set weird on/off blocks for every room throughout the night/day to try and save…
-
Always show temperature on Tado ac
Have an option to set Tado ac to always show the current room temperature on display.
-
Graph showing global boiler activity
I don’t think this exists, or I cannot find it. I’d love to be able to see the pattern of when my boiler is active globally rather than when each room is calling for heat.
-
Open or close valve without controlling heating system
It would be nice if we could control the valve full open or fully closed without start/stop heating system. Example, i need a radiator always opened because of the pressure system and dont want it to control the heating system, just let the current water flow in.
-
Relay and Opentherm together
The Tado extension kit can control the boiler through a relay (simple on-off switch) or through the Opentherm bus. The bus allows for better temperature stability and higher efficiency as it tells the boiler to turn the heating up or down as necessary. If a heating system contains other elements, like a shut-off valve or…
-
eliminazione modalità operativa su Termostato
Salve volevo farvi ragionare sulla scelta di eliminare la possibilità di impostare la modalità operativa su Termostato con il controllo clima In pratica adesso questa funzione non è più utilizzata perchè ritenuta obsoleta. Sono in disaccordo. Attualmente con l'ultimo aggiornamento avete impostato che il controllo clima da…
-
Comfort screen settings
Ability change the comfort range and set a min/max in the comfort toggle
-
Away mode schedule
It would be great if Tado would support an away mode schedule: a schedule that only operates when away mode is triggered, instead of the current single away mode temperature. My use case: due to dynamic energy pricing it is wise to start heating around noon, even if I'm away. But if I'm home in the morning than heating…