-
How to prevent radiator valves whistling?
Hi Sometimes my radiators are wheezing (not just with the Tado smart valves, but the old manual ones too), I think when most of them are closed and a few ones are barely open. this only happens when Tado sets them to 'barely open', in the past I've prevented this by either fully closing on having them on medium-high…
-
Which adaptor to use
I have an Ecopal thermostatic radiator valve on an existing radiator and want to replace it with a tado smart radiator valve. Looking through the list of thermostat valves in the help it is not listed. Any idea if an adaptor is required or not please?
-
Moved into a house with Tado, can't get the heating to come on
Hi All, We moved into our property last February, we found the smart thermostat and have never had an issue in getting the heating to come on. About 8 weeks ago we had a gas engineer come out to look at our boiler he said that I needed to download the Tado app which I did, ever since then we cannot get the heating to come…
-
Has anyone wired a tado v3+ to a vaillant ecotec pro 28 combi boiler?
I am after a video or images of where the wires are fitted in the boiler and the receiver. The boiler has a built in timer and it's a 1st time after tado is fitted that it will have a thermostat.Thanks Neil
-
Pairing WIRED thermostats
I've got 2 WIRED thermostats and a wireless receiver. Do I to pair each WIRED thermostat with the receiver?
-
correct wiring for smart thermostat
need some guidance on how to correctly wire a wired smart thermostat. I'm attaching a pic of how the old thermostat was wired, showing L jumpered to COM and the control blue & brown wires connected to N & NO respectively. On the Tado thermostat I've tried connecting L straight on COM, the control brown wire connected to…
-
2 floors small apartment
Hi everyone, I need help in order to understand what I need. I have a small 50sqm apartment, first floor is living + kitchen, and second floor is for the bedroom and bathroom. I will update my boiler on January with a condensing one. The thermostat is on the second floor and the problem is that the living room temperature…
-
Clarification of how to set up TRV vales (V3+)
The more I read the more confused I get 🤔 Our bungalow set up is: Wired thermostat in unheated hallway. Four individual rooms each having Radiator thermostat. (more properly when I change the Drayton V2 rad valves there will be four rooms😀) Two other rooms with non-TRVs, to act as heat sinks. I want it setup so that each…
-
Does the temperature sensor read humidity / does offsetting temp change relative humidity reading?
Hi, I'm sat here with my Tado wireless temperature sensor next to 2 separate humidity sensors. My stats are: Sensor 1: 56% humidity / 19.7°C Sensor 2: 57% humidity / 19.5°C Tado: 74% humidity / 18°C The Tado is obviously way off the other sensors. It is set as my 'measuring device' for this room, which also contains a TRV.…
-
Is Thermostat X backward compatible with previous Tado TRVs?
We have 16 radiators! And a Thermostat X ... If I can pick up a few of the original smart TRVs for our less used rooms, I can save quite a few quid. I appreciate they don't use sub-GHz Matter, but if they have line of sight, can Thermostat X see them?
-
Tado wall thermostat triggering boiler despite no heat demand
Ive been using tado, and have it integrated in to Home Assistant, for 4 or so years with no real issues. Until this season; suddenly my wall thermostat regularly triggers my boiler, despite there being no heat demand from any of the TRVs or the wall thermostat itself, as seen both in the tado app, and in Home Assistant…
-
A little help with choosing the right kit
Hi all, apologies have had a little look but unsure with what route to take. Our new home has a ProCombi exclusive 35 boiler with an old TFC wireless stat. Am looking to replace with Tado. What it be compatible and advantageous to install the Opentherm version if even compatible or should I go non opentherm. Then to add to…
-
Two wireless receivers operating a single NO valve
I’ve hit the dreaded “10 rooms” limit. My plumbing has only one heating circuit, controlled by a valve that is “normally open” and I have a Wireless Receiver acting as zone controller. It is connected to the boiler control via the “CH NO” terminal. To get around the limit, can I buy a second Wireless Receiver, and wire it…
-
Tado trv compatability flowmaster trv
Hello everyone thanks for the add I'm Steve. Looking to add some smart trv's will the tado fit flowmaster trv's? Yours Steve
-
Behaviour of Zoned vs Independent TRVs . . .
I wonder whether anyone else feels that the tadoº TRVs behave differently with regard to opening and closing when they are set to independent in contrast to when they are assigned to a zone controller and able to call for heat. For this year’s heating season I have made several of the TRVs in the “communal” areas of the…
-
Vokera Syntesi - hot water but no heating
I have had a tado installed it is all connected to each other and can see everything on app, but when I increase heating in the app it doesn't switch the boiler on. Hot water works but no heating. I would appreciate any suggestions, I put it into test mode and it kicked the boiler in the straight off again.
-
Wireless receiver not connecting to bridge so boiler doesn't respond and schedule not stuck to
Moved into a house last month with Tado. Set up an account okay and connected to the thermostat. Internet bridge set-up next to internet router but seemed too far away to connect to the receiver which is connected to the boiler. Took the time to buy a WiFi booster so the internet bridge is now connected much closer to the…
-
Setup for centralized heating without direct boiler control
Hello, I need an advise which setup to use to control my house heating. I have centralized heating in my condominium, which is not under my control. I have a radiators with manual valves and I want to replace these manual valves with the ones that can control ambient temperature in the room. My questions: is built-in valve…
-
Tado app working and all devices connected but boiler not firing up when the app calls for heat
My system is about 7 years old, not sure what version but is hard wired with an internet bridge and extension kit. In the last week, the boiler has stopped firing up when tado calls for heating or hot water. I then have to switch everything off and then on (bridge/extension kit & boiler) and it starts. Has anyone had this…
-
Not sure about compatibility
Hello, i want to purchase tado thermostat X with the valves for a complete control but im no sure if it is compatible. The gas condesning boiler is Riello Residence HM 30 KIS. Anyone has any experience with this?
-
Guide for replacing faulty Tado wired smart thermostat with a new one?
I've 2x Tado wired smart thermostats (upstairs and downstairs heating) and 1x extension bridge (for hot water) The downstairs smart thermostat went offline a few days ago and won't come back. It controls heating downstairs and the hot water via an extension bridge. Tried all the usual re-pairing, moving the bridge beside…
-
New DIY install replacing TP9000
I have a viessmann system boiler and hot water tank controlled by a Danfoss TP9000 on the 1st floor landing which schedules the HW and CH. I'm looking to DIY install the Tado V3+ Wireless Heating & Hot Water Smart Thermostat Starter Kit. I'll replace the TP9000 (no remote sensors) with the wireless reciever which appears…
-
Replaced Drayron RTS1 thermostat with wired Tado, now heating doesn't work
We have a simple, but unusual, for the UK, heating system. The cylinder is a thermal store, whereby the main water content is heated by an, always on, Bosch gas boiler, but is supplemented by heat from a solar panel and a solid fuel boiler. This cylinder water is used as the water for the heating system, and, by use of…
-
App not showing data
I have recently updated the app due to an error message I was receiving and since then it no longer shows when the heating has been on/off. Also, previously I was able to control the amount of time the heating was on for and any following Alexa requests would put the heating on for the amount of time specified previously.…
-
Help with eph r27 and cylinder thermostat
We have a Glow Worm Energy 18s boiler with the following control system: https://drive.google.com/file/d/18EfZF0DIOBtxWuHFIiVSJj80KLKqL7e7/view?usp=drive_link The panel connected to the boiler controls the scheduling of the upstairs heating and the hot water. Upstairs there's one wired thermostat that controls the heating…
-
Installation
I have a Worcester Greenstar 30si boiler with Siemens RAA200 hard wired controls and I want to fit the Tado hardwired thermostat it place of existing controls. My Siemens room stat wiring diagram shows 2 cables 1 into L and other cable into Y1. Where would I put these cables on the tado stat
-
3-day standard for help line answers?
Do I get it right that the helpline needs 3 days to reply to requests? What is the standard for response time?
-
Boiler only comes on when heating is on but not when only hot water is on
Hi, I have a strange issue where the boiler only fires when I turn on the central heating, this turns on both the central heating and hot water. Turning just the hot water on, it show in Tado receiver that the hot water is on but the boiler doesn't fire. I believe I have a S plan and the 3rd and 4th pictures are of the…
-
add-on wireless temp sensor or add-on smart thermostat?
quick question. i have a tado sytem already in place (uk combi boiler), controlling just heating 1 zone. 3 rads with smart trvs. smart thermostat running as a wireless temp sensor. i want to add a wirless temp sensor in the other 2 rooms that only have the smart TRVs for better/more accurate temps. on the store they have a…
-
If I have smart radiator thermostat in every room is there much use for the wireless thermostat
Question is in the title. I have smart radiator thermostat in every room and can control the temp from my phone, so is there any reason to have the general smart thermostat on my wall? Also is there any way to see a history of when my heating turns on? I can see a history per radiator but I wanted an overall view to make…