It has been a while since this request was made and I would like to join in to support this. Even though Tado might be following standards, some people just like it a bit colder than others (or like to wear sweaters).
It would be great if we could adjust the comfortable temperature to what we ourselves find comfortable.
Thanks in advance and take care.
With tado I can change the temperature of my hot water (between 40 en 65 degrees celsius) but I cannot change the hot water to ecomode or off, which should be possible with the opentherm communication of this heater. Therefore, I would like these functions to be added to the Tado possibilities.
Just as an update: I have disabled early start for the smaller rooms I am using the smart radiators in. The algorithm starts way too early to be effective in these situations. It will push for almost full power & then heat the rooms in 15 minutes. And then you wait 3 hours for when you actually need the heat. And the system doesn't really seem to be learning at all here.
So a suggestion like I put forward above is really necessary in order to make early start usable there.
Wat is een PID regeling dan?
I recently removed a Smart Radiator Thermostat from my home and removed it from the Tado app, however it is still showing in HomeKit.
Having spoken to support the only way to fix this is to remove the Internet gateway from HomeKit, do a factory reset on it, and re-add it to HomeKit. This will however have the side effect of removing all my Tado devices from the HomeKit scenes and shortcuts I have referenced them in.
My suggested improvement is to have the Tado app remove a device from HomeKit at the same time it is removed from the Tado app, or have an option to 'resync' the Tado devices with HomeKit.
Een kinderslot is wel handig.. als je per ongeluk tegen de knop aankomt met schoonmaken of de kinderen komen eraan dan staat hij op handmatige bediening
Hi @kozaka & @crashnick16 ,
I have since found that the "Notification" actually is automatically removed in line with the 'duration' set by the user when the 'Enable' setting is set up.
For example if the duration (for shutting down) the relevant Tado Room is set to 20 mins then this 'timescale' is also applied to the 'removal' of the "Notification"......ie the "Notification" will disappear after 20 mins.........I have tried this on 3 different duration settings, and the "Notification" has disappeared as per the 'duration' setting.
With working from home being more common I need heating focused heating in the office and no other rooms whilr it is just me in the house.
The other accounts I.E. The kids/wife need heat to the other rooms when they get home and in the evening (out of work hours)
- allow setting a 'home-working skill' in which you specify the 'office' and the people who work there and which hours to use it before returning to full house 'home' mode for evening etc.
- For each geofencing account have a checklist of rooms in which heating is turned on for that user when home. I.e. Only those devices are set to home mode.
A smart energy saving system that isn't smart or energy saving? Really? Come on; surely you can do better than this! This is basic functionality surely?
It would be great if the iOS app implement
"Actionable notification" (https://developer.apple.com/documentation/usernotifications/declaring_your_actionable_notification_types)
This way, when ever there is a notification (eg: turn on/off away mode, window open detected). I can immediately take action WITHOUT opening the tado app. This is also very nice for people with Apple WATCH. They can take action even without opening their phone
Sometimes I use the tado app to heat my home office because I intent to use it later in the day.
I would appreciate a push notification on my phone to tell me that that my home office is successfully heated and ready for use.
@GrayDav4276 you mean Auto, Home, Away? If so then no as that applies to the whole house for all occupants.
This is a per-user + per-room feature/skill ;)
In an ideal world the radiators would know your proximity to them and then on accordingly... However that would not be possible yet. Instead being able to have the office heated when I am present in the house between 9-5 is not possible without tweaking manually each time as other occupants can easily be present so needs some per-user geofencing options or specific skill.
@GrayDav4276 i have owned the tado system for years and they have already implemented a few suggestions. As a software developer I have full understanding of this additional feature, its actually a minor refractor in the application software to extend to separate device account settings. Essentially, you should discuss the feature and not the technical aspects in any forum as it is for the tado development team to guage the work involved. Cheers.
@GrayDav4276 The current Geofencing function that Tado provides works exactly the way I expect it to.
Apologies if I have misinterpreted the comments made by other Community Members regarding the functionality of some/many Tado features.
I will ensure that I do not respond in the future with anything that people may perceive as an inherent bias.
Just to clarify:
I like my Tado products (10 SRT's / 1 Wireless Thermostat / Extension Kit / Bridge) I have 4 of my SRT's set as "INDEPENDENT" and I also use 2 x dumb TRV's in my set up......which works very well.......So I am actually a 'fan' of the Tado system.
I will apply a personal filter when reading & before responding to posts made by other Community Members to ensure that I do not cause other members to feel unhappy/annoyed by my comments.
So.....to lighten the mood somewhat......"I'll get me coat" (Fast Show) 🙃
@GrayDav4276 Well I for one would not wish you to curtail in any way your truly excellent contribution here. We all were allocated toes in order for someone to step on them!!
just have smart SRVs in all rooms ( which you will need anyway ) then you can just heat the "office" without heating the rest of the house by setting to away then just set the office temp to what you want. Or just create a routine that does that "Alexa just me working"
Would it be possible to add a field to the 'Rooms and Devices' tab where users can store a history of each TRV - when batteries were last changes / when the TRV was reseated / when issues occurred.
I am having to keep a separate log of all of these types of interactions and it would be more convenient to store it on the system,
I might also be useful for a TADO customer rep. to view if a user has issues.
I think you may be correct.....yes I like Alexa too ✔️😎
I know there have been a lot of discussion and requests to Tado to make it possible that there could be more than one internet bridge connected to one system / account. The first requests date from 2018.
I see also that a lot of customers are angry / disappointed towards Tado because little is done with regard to this request. And nobody (even an Tado support guy I'm in contact with) knows what the current situation is (he advised me to send my request to this forum). There are even customers who are (especially regarding the lack of communication from Tado about this topic) willing to stop using the Tado system and install a system of one of the competitors.
Could one of the Tado employee please be so kind to give me (us) an update regarding this request? Is there all ready a release planned to add this functionality tot the system and what is the expected date that the functionality will become available?
For me personally, I really need this functionality to cover all the rooms in our house (just as many other customers and yes, I have already done all the steps to connect all the heaters with just one internet bridge).
I hope to hear from so one of Tado employees soon (hopefully with good news that the functionality will be available in January or February 2021).
Ps. I know that there are already a lot of threads regarding this topic. And I choose to start a new one, to hopefully get the right attention regarding this topic.