-
make geofencing free.
I was always surprised that geofencing needed a subscription. When receiving this email below. Geofencing has a much bigger impact. So make geofencing free. "Take action now to reduce energy consumption in a joint effort Hello Robert, Did you know that lowering your home temperature by 1°C will reduce energy consumption by…
-
Unify AC V3+ experience with the rest of the Tado products
Hi, I have multiple Tado products in my home - 5x RTV, 1x Thermostat, 1x Home Bridge, 1x AC controller. The experience across these devices is so different that the AC controller almost feels like it was made by a different company (it is not great). Would it be possible to enable pairing of the AC controller with the Tado…
-
Heat pump simulation mode
With ASHPs being pushed so aggressively in the U.K. and with Tado users likely being on the forefront of heating efficiency, it seems to me that a ‘simulation’ mode would be helpful. The idea would be that tado (when linked to digital connections) would cap the max water temp at 55 deg and ideally target lower temps. It…
-
zones
hi guys any chance of a feature that allows you to block rooms together. i.e. upstairs/downstairs/bedrooms. you could simply call them zones. if you can and the boost into this aswell so hitting "boost upstairs" would heat everything in your "upstairs" zone. tell me what you think, thanks
-
Set a maximum radiator temperature, to keep the boiler condensing efficiently.
Hi, Tado achieves a lot of its efficiency by modulating the boiler temperature. However, the variability in environmental temperature makes it very difficult to produce a room temperature profile that will not a some point be caught out, resulting in the boiler going to its maximum output temperature for a short period of…
-
Add WPA3 support to AC V3+ Controller
Hi, would it be possible to add support for WPA3 to the Smart AC V3+ controller? This security protocol is becoming the new standard, and right now, at least on my network, it is the only device that doesn't support this protocol. Cheers
-
Extra safety feature
For some reason my Tado heated up to 57c after a change of installation in the setup menu. Therefore I think a check/failsafe in the firmware of the Tado for when the temperature goes up to more then 30c in a short period it should turn itself of and give a notice in the app. It melted My Tado wired where you press to turn…
-
Add Humididty to Climatecomfort screen
Could you add humidity next to C° on the screen ? See screen capture Thx
-
Essential Tado App Improvements
Hi everyone, I have been asked by Tado to post my request that the IQ energy facility within our Tado Apps be updated to include our electricity readings. This because... wait for it, you're not going to believe this... So us Tado Customers can vote on whether this should be included within the App. I can almost hear the…
-
"Advance Heating" Feature
This is a standard feature in most heating systems - some form of control to advance the heating to its next programmed state. Scenario - it's 22:00 and I want to go to bed early and turn the heating off. The heating is programmed to be on until 23:00. Of course if I TURN OFF all rooms that works, but the problem here is…
-
3rd party temperature sensors
It would be a great improvement if one could have the ability to use a temperature sensor already in the room (which is i.e., HomeKit compatible) to control the radiator valves. This will give a much more accurate temperature control in each room. If you already have a temperature sensor in the room used for another…
-
Home area shape and geolocation.
Unless I'm missing some obvious features, what I've found is that currently the home area for geolocation is a simple circle set from your house, could it be drawn on the map to be more specific to the area you live. I.e my missus works close to home which is within our correct recommended home circle. If you could draw…
-
Add support of CAN-Bus
Many pellet boilers manufacturers (Froling, Guntamatic, Hargassner, Herz, ....) are using CAN-Bus modulating thermostats. Would be great if Tado could support CAN-Bus protocol in order to replace these thermostats, in modulating mode
-
Maximum Temperature of the Boiler
I use tado on eBus interface. I want to set up myself the maxim temperature from the boiler. The condensing boilers are most efficient at 55-60%.
-
Changing the maximum flow temperature myself
Initial problem: Hello, i have a Ferroli Bluehelix PRO 32C heating central. I use tado for 3 years now. After last update of Tado APP to version 6.0.2 (9826) i found following bug. I limit maximum temperature of heating using heating buttons on my boiler to 55C. After this update, maximum flow temperature is reseting…
-
6.38 crashes on my iOS device but 6.37 doesn’t
After reporting a crashing bug I saw on iOS. I’ve been prompted to help by suggesting a feature after relating the information that I essentially rolled back the version from 6.38 to 6.37. So I guess the new feature could be: How about new beta test 6.38 doesn’t crash like 6.37 didn’t? :) The application //started showing.…
-
Cumulative daily activity
Can the graphs that show daily temperature and heating/cooling activity by room also be provide as a cumulative of all thermostat sensors. This would provide insight into where and when most energy is being used and allow for further fine-tuning.
-
Radiator thermostat colours.
Does any one agree with me that it would be really useful if there was a range of colours for the radiator thermostats? They could be available to match the many colours of radiators that are available. My new radiators are anthracite and the white Tado thermostats seem a little out of place.