Active

Worcester Bosch Greenstar 8000 and EMS
Please can you configure the Tado wired unit to work with the Worcester Bosch Greenstar 8000 and EMS
Stabilizing heat demand pattern for constant set temperature
I live in Scandinavia and often work from home, so I have a consistent heating demand throughout the day. When looking at the temperature/heating graph view, it is clear that the heating demand (and temperature) follows a cyclic pattern with a period of 45min on average. I'd love to post an image but I don't think this…
Let users choose which rooms to 'boost'
I’m sorry if I’ve missed this, but how on earth can I hit Boost and boost just a set of rooms rather than the ones which are not used? This is such a no-brainer feature, and when I search I can only find hack-arounds via IFTTT ( just discovered now not possible ) I can only assume that this is me being thick? Feature =…
Ebus Max Flow Temperature setting (like the one just released for Opentherm).
Would it be possible to do the same for Ebus controlled boilers via the wired Tado, +- settings? My Vaillant can ramp up to 80C if it wants even if I set the max temp lower on the boiler. The ebus will ignore these settings and do what it feels is best. I might only want it to go to 66 or 70C max for example. It's just…
user rights
There is a need for user rights in the app. An administrator can do and change the complete setup. But it should be possible to add users that as an example only can change temperatures within a certain range. Now, I am worried that a user who is less technical by mistake will change a parameter or delete something in the…
tado GmbH Incident - degraded performance affecting the tado° app - 19 November 2024
Yesterday, as reported by tado GmbG Inicident, there was a temporary degraded performance affecting the tado app. Just to inform you how this incident may have affected my Panasonic Aquarea heat pump system. It appeared that the heat pump did not warm the house at all for some hours. Due to the heat already present in the…
Give users access to the advanced configuration parameters
As most of us here will be aware, Tado has several advanced controls and configuration options that support are able to use to configure your devices when you contact them (cycle periods, minimum on/off times etc). Sadly these advanced options are hidden from users and the only way to access them is through support which…
Profiles (again)
How much work will there be to enable us to create differnt profiles in the app? I know its been asked before but users seem to have an answer by adjusting the existing home profiles. I DONT WANT TO DO THIS. I want to press a button when for example we have guests staying or if we have a snow day or i'm working from home…
Schedule profiles
I have now had the tado system for nearly a week, and its certainly better than my old hive system. You guys have done a good job on it. However you (and every competitor) are missing what I believe is probably an important feature for many people, and I can say 100% would have made me choose to move to you years ago had…
Dedicated tile for boiler status on/off (same as hot water)
Im fairly new to Tado but one feature i've seen that is so blindly obvious i though i was doing something wrong. It would be great to have a tile on the app which shows if the wireless recevier is actively calling for heat. Similar to the "hot water on/off" tile. A boiler on/off tile. I know there are the ~~~ wavey lines…
Schedule a boost
I am often away from home. My underfloor heating has a 24 hour thermal lag from 6 degrees to 22 degrees. I regularly forget to preheat it. Can you please add a facility to diarise a temperature boost for one or more rooms?
Smart Global Off Time with Conditional Notifications
Overview: I’d like to propose a feature that allows users to set a "Global Off Time"—a hard cutoff time at which all heating devices in the system are turned off or reverted to a predefined safe state (e.g., frost protection). This feature would address the issue of unexpected heating events during the night, offering…
Ability to rename device
When batteries are running low I get an email informing me that a particular device in a specific room has an issue. In some rooms I have 4 radiators. I then have to go round ‘blinking’ the stat multiple and watching all the stats in the room to find which one it is. it would be great to be able to rename or give a…
Offline notification
My Internet Bridge went off-line and I didn't realise for hours. A simple reset was all it took to fix the issue, which I could have done way sooner if I'd realised. Tado sends other notifications, like a thermostat needing batteries. I would like Tado to send me a notification, either push-notification in the app, or…
Worcester Bosch 4000 ems control
Please enable support of EMS / Ebus functionality so Tado can control modulation of this boiler
Tado feature request: 8-10 degree C mode support
Hi, I have 2 Tado AC controllers. I have been pretty happy with the one in our house, and purchased a 2nd one last week for our summer cottage. We recently installed a new Panasonic AC-model in the cottage, and during the winter, the AC is set to 8 degrees C to keep the house dry and frost free. I assumed that Tado would…
Pre-heat and early start for Tado X
Hello, Just bought the tado x System and I am a bit disappointed that the pre-heat and early start feature are missing. Are there any plans to implement those two features? Please implement those two features🙏 Thanks, Florian

Active

Discussion List