"Summer/Cooling mode" for wall thermostat
Comments
-
Usually the response how to set all thermostats in summer is to set OFF - but this is wrong, spring of the valve is pressed whole summer and can get stuck when heating season is back and also this reduce "the life" of the valve.
Now, there is no way in the app to set all valves to fully open state for summer, I had to manually remove all tado's Smart Radiator Thermostats from all radiators to achieve the state, which is quite annoying.
It would be nice to have a specific Summer mode in which all thermostats are set to "fully open" state.
0 -
Same required for me. We have a larger chiller on the roof which pumps cold water through the house in the summer. I'd like to control the cooling features. It doesn't even need to control the chiller, which is always on anyway.
1 -
maybe against the policies of this forum but someone found an alternative solution besides Tado Smart Radiator valve?
0 -
Hi,
Two years ago I put underfloor heating but kept my gas boiler. Two years ago I also invested a lot of money in Tado system (6 wall thermostats, wifi receiver, GW) but now as a LOT OF PEOPLE I change my gas boiler to heating cooling Daikin system because gas is very expensive and Aerotermia is much more efficient.
I opened a support ticket to know if it exist any option to have a summer mode to be able to enjoy also the cooling system (here in Spain in summer is very hot) and they said not for now and redirected me to this community.
And I discovered more people are in the same situation as me.
Now Tado team, please take time to understand the request here because we are not asking for any hardware change but only a summer mode that can be activated to invert the logic (when reaching 26 open and when reaching 25 close) with also a summer programmation.
Please can you provide update about the development?
Thank you
2 -
Pretty disappointed about this too.. considering switching completely..
What I guess most of us forget is that tado is german-based and a lot of their customer base resides in Germany (me included). Until the war in Ukraine, nobody here gave a damn about modern heating so there was never really a reason to focus on this. Which is also partly why the country faces a big problem with heat pump shortages now. Unfortunately.
It would be great to know if this is even being worked on at tado. If not, I will look to switch vendor.2 -
Good Day
Despite I Suárez the concern of this forum and I am algo aslin Tado to put a summer Mode, this is what I do to manage my cooling system. In summer, in the sentina área of each room I modify the temperature corrección by compesating with -10°C. Then I Just pull the descrédito temp above 25°C to get cooled Walter into my heaters. It is a simple way to get cooling works, but again there should be easier ways (in this Wayne temp regulación is manually achieved)2 -
Good Day
Despite I share the concern of this forum and I am algo asking Tado to put a summer Mode, this is what I do to manage my cooling system. In summer, in the senttings area of each room I modify the temperature compensation with -10°C. Then I just pull the temp above 25°C in the rooms I need, to get cooled water flow into my heaters (with fans). It is a simple way to get cooling works, but again there should be easier and better ways that Tado should support2 -
Hi Tado Team, any update of this request/feature? Hope this will be implemented fro the nest summer!
thank you in advance for your answer and hard work!
1 -
Just to re-iterate to Tado my heating/cooling scenario...
I have an Ochsner Air source heat pump system which has it's own internal and external thermostat which act as a master control for wether the heatpump should be be On/Off and i can configure as well a cooling mode on it in the summer.
The Tado wired thermostats which I have are in the various rooms and only ever control the actuators on the UFH manifold inorder to open close the hot/cool water circuits.
I configured the Heat pump now to run the cooling program which targets getting the master thermostat down to 25 degrees, we had already 20 days reaching well above 30 where i am based in central Europe.
Use case: When a room is already cooled to 25degrees Tado closes the circuit in that rooms so other rooms can cool more efficiently. When a room is over 25degrees tado should the circuit to allow cooling.
As everyone keeps pointing out, logically it feels like this should just be a toggle in the coded logic of the tado app/firmware on the thermstats... to get the actuators to be controlled differently.
Grateful for any update from Tado team. Thanks
1 -
Same goes for the Netherlands and Belgium. Look at the Dutch forum where this has been a top-request for the past 3(!!) years.
I know that heat-pumps, also providing a cooling function over low temp water heating systems, is very common in Scandinavian and German countries too. That should all and all, meanwhile be a large chunk of the EU market.
1 -
I strongly agree with the above request. I now have stuck valves..........
0 -
I'm in the UK, so temperatures above 25C are not that common here. I have eight SRTs, all set as independent, so they cannot request the boiler to fire. Throughout summer I have them set to 25C, so most of the time they remain fully open, at least overnight. If temps do reach 25+ then they will close down, but there's no harm in that occasional exercise to keep the pins free.
In fact, with that in mind, I recently adjusted the schedule for all valves to turn off at 22:00 and resume 25C at midnight. That way they get at least one cycle per 24 hours, but are mostly left open for 22 hours at a time.
Perhaps in warmer climates this plan won't work so well, but it's great for me in the UK.
0 -
I do nothing at all to protect my valves and they have been in operation since 1990 and I have only had one with a small issue and even then it was not stuck. I know of many who adopt the same non-practice as myself with no issues. Semper eadem!
2 -
It's very common in Hungary too in new modern homes to have heat pumps supporting (by circulating hot water in the floor and cold water in the ceiling ) to support both heating and cooling.
I'm very surprised that TADO doesn't support this by default.
So listen to your customers!1 -
Any news Tado?
This is very very common in Spain and it is very simple to implement in your software.
Just remember that you have also to increase the maximum temperature limit, because in "summer mode" 25ºC is a bit cold.
I'm waiting for you to implement this issue I and I will buy your equipment.
1 -
Hi friends,
I'm currently considering which thermostat option to buy.
We're looking for a thermostat that allows us to fully operate a system with both heating/cooling floor system with fancoil as an added resource.
We find Tado to be a potential option due to how powerful its heating floor system works; however, not having a way to use this same system to get cold water flowing and just hot water makes it a hard decision for us to make.
We've found other brands like Meross have their thermostats updated so that they include what they call "Summer mode", enabling full operation over both heating and cooling floors.
Could I ask Tado users whether you've found a way to make this work?
Main reason why we'd prefer Tado over other brands such as Meross is that Tado has its thermostats plugged via Ethernet, and not Wifi.
Thanks!
1 -
Tado thermostats aren’t connected via Ethernet (or WiFi) so you might be better off looking at something that meets your requirements.0
-
It is possible to set all valves to fully open state for summer in the app.
Go to Settings -- Choose a room -- Heating Zone -- Zone Controller -- set it to "independent".
Do this for all rooms.
Then set all TRVs to the max temperature.
This way, TRVs should remain open all the time (perhaps except the time when the temperature in the room exceeds 25 degrees..) and there should be no heating as they're disconnected from the zone controller.
0 -
I wanted to add my +1, in EU cooling/heating flooring systems are more and more common and it seems logical for companies to start supporting them. The Spanish community has also a discussion about this, and it looks like others too. We should all vote for this feature to be added.
@Rob we know the teams are working on it but we would really appreciate an update (if possible)
1 -
I'm new to Tado. In fact I only fitted my valves two days ago.
I was immediately surprised that there was no bespoke summer setting but yours seems to be the most logical solution I’ve seen. Problem is I can’t see the settings you’re describing particularly where is the ‘independent’ setting. Can you elaborate? Where do I find it. Sorry if I sound a bit clueless!
0 -
..............................
0 -
Always surprised that since TRV started to appear (yes, I remember the non-thermostat radiator valves ;), I have yet to experience a stuck valve or have heard from friends and family about stuck valves. I have been in at least 5 different apartments with TRVs. No issues whatsoever. And they were all older equipment and a mix of manufacturers.
I think Tado is not adding that feature because it only affects a very small number of users.
0 -
This content has been removed.
-
I get what people.are saying, but I've never had a problem with a TRV (touches wood...) and I'll definitely look into what eezytiger has mentioned as that looks like an interesting function.
My pennyworth for a short term solution would be to either build time into the schedule to automatically open the valve fully (midday as it's the hottest time of the day?)... or manually Boost Heating for a few minutes to get all the valves open and the system going: you have control then and it wouldn't have to be every day or for more than a few minutes.. just enough to relax the springs..
Isn't the number one time for breakdowns of boilers and radiators is at the start of autumn/winter because during the summer they haven't been used..?0 -
I cannot believe this is still not happening. As all of you said, a simple reverse of the logic would be totally sufficient. This is literally something a junior developer can do in his first year. The correction of the temperature doesn't really work very nicely when you have 20 thermostats.
BTW, as I don't see this happening anymore from tado as they obviously just don't give a rats *naughtyword*, I have 20 wall thermostats and a bridge up for sale in Germany. loomsen at gmail, if anyone is interested.
Beyond ridiculous.
1 -
Another potential customer in France with underfloor heating/cooling in an apartment. In my case the heat pump is at building level, and the only control I have in my apartment is to turn on the valve for my underfloor on, or turn it off. In the winter, warm water comes through the pipes, and in the summer they switch the whole building and the same valve gives me cool water.
As others have said, I think a simple logic inversion for a heating to cooling mode switch is all that's needed to make the smart thermostat work in my case.
Pretty please!2 -
Another potential customer in Spain lost. I have underfloor heating/cooling floor. I liked to go with tado but it seems that they don´t listen the community. Going with Meross, they listened their community and added a summer mode. Pretty dissapointed with TADO, years asking for something and no response.
2 -
Same here in the UK, I’m just about to get the reversible heat pump installed and am horrified to learn that this SOFTWARE option doesn’t exist.3
-
Just posting another +1 here to raise awareness for this issue. I'm looking also for cooling functionality.
3
