-
Please search for your request before opening a new thread.
Dear Community Members, This part of the forum is intended to help us track the features that you, our customers, are interested in. We understand that you, as members of our forum, tend to represent more experienced users, often with in-depth knowledge of not only tado°, but similar products and services as well. We feel…
-
Ebus Max Flow Temperature setting (like the one just released for Opentherm).
Would it be possible to do the same for Ebus controlled boilers via the wired Tado, +- settings? My Vaillant can ramp up to 80C if it wants even if I set the max temp lower on the boiler. The ebus will ignore these settings and do what it feels is best. I might only want it to go to 66 or 70C max for example. It's just…
-
user rights
There is a need for user rights in the app. An administrator can do and change the complete setup. But it should be possible to add users that as an example only can change temperatures within a certain range. Now, I am worried that a user who is less technical by mistake will change a parameter or delete something in the…
-
tado GmbH Incident - degraded performance affecting the tado° app - 19 November 2024
Yesterday, as reported by tado GmbG Inicident, there was a temporary degraded performance affecting the tado app. Just to inform you how this incident may have affected my Panasonic Aquarea heat pump system. It appeared that the heat pump did not warm the house at all for some hours. Due to the heat already present in the…
-
Give users access to the advanced configuration parameters
As most of us here will be aware, Tado has several advanced controls and configuration options that support are able to use to configure your devices when you contact them (cycle periods, minimum on/off times etc). Sadly these advanced options are hidden from users and the only way to access them is through support which…
-
Profiles (again)
How much work will there be to enable us to create differnt profiles in the app? I know its been asked before but users seem to have an answer by adjusting the existing home profiles. I DONT WANT TO DO THIS. I want to press a button when for example we have guests staying or if we have a snow day or i'm working from home…
-
Schedule profiles
I have now had the tado system for nearly a week, and its certainly better than my old hive system. You guys have done a good job on it. However you (and every competitor) are missing what I believe is probably an important feature for many people, and I can say 100% would have made me choose to move to you years ago had…
-
Dedicated tile for boiler status on/off (same as hot water)
Im fairly new to Tado but one feature i've seen that is so blindly obvious i though i was doing something wrong. It would be great to have a tile on the app which shows if the wireless recevier is actively calling for heat. Similar to the "hot water on/off" tile. A boiler on/off tile. I know there are the ~~~ wavey lines…
-
Schedule a boost
I am often away from home. My underfloor heating has a 24 hour thermal lag from 6 degrees to 22 degrees. I regularly forget to preheat it. Can you please add a facility to diarise a temperature boost for one or more rooms?
-
Smart Global Off Time with Conditional Notifications
Overview: I’d like to propose a feature that allows users to set a "Global Off Time"—a hard cutoff time at which all heating devices in the system are turned off or reverted to a predefined safe state (e.g., frost protection). This feature would address the issue of unexpected heating events during the night, offering…
-
Ability to rename device
When batteries are running low I get an email informing me that a particular device in a specific room has an issue. In some rooms I have 4 radiators. I then have to go round ‘blinking’ the stat multiple and watching all the stats in the room to find which one it is. it would be great to be able to rename or give a…
-
[Release] OpenTherm Max Flow Temperature setting
On 28.10.2022 we have added the option to set the maximum flow temperature for OpenTherm configured tado thermostats / Extension Kits / Wireless Receivers without contacting our support department. From this moment forward, your installer will have the possibility to set the maximum flow temperature on V3/V3+ homes (your…
-
Offline notification
My Internet Bridge went off-line and I didn't realise for hours. A simple reset was all it took to fix the issue, which I could have done way sooner if I'd realised. Tado sends other notifications, like a thermostat needing batteries. I would like Tado to send me a notification, either push-notification in the app, or…
-
Worcester Bosch 4000 ems control
Please enable support of EMS / Ebus functionality so Tado can control modulation of this boiler
-
Pre-heat and early start for Tado X
Hello, Just bought the tado x System and I am a bit disappointed that the pre-heat and early start feature are missing. Are there any plans to implement those two features? Please implement those two features🙏 Thanks, Florian
-
Provide method to specify type of heating system, i.e. radiators, underfloor, etc.
There is no facility to specify what type of heating system is installed. It appears Tado treats all systems as if the heating system is based on radiators. In case of a underfloor only system it is likely the floor is cold when the first call for heat after a break is generated. Currently the system would start to run for…
-
3rd party temperature sensor support or cheaper add-on temperature sensor
I have multiple tado radiator thermostats, but all of them are a couple of degrees out with the actual temperature. I use an Aqara temperature sensor to measure the actual temperature in the room, further away from my radiator. It would be great if the tado app could use the data of these aqara sensors to measure the…
-
allow changing the name of devices
Please allow us to change the names of devices to make it easier to identify them. For example, getting an email that tells me: "We have noticed that the batteries in your Smart Radiator Thermostat VA*******048 in the zone ****** are running low." I have 15 devices and if each device had a name I wouldn't have to waste…
-
Notificación al móvil en caso de encendido/apagado de calefacción
Una sencilla forma de saber si se ha puesto en marcha la calefacción en nuestra casa (o en una estancia de ella) a través de una notificación al móvil (tira o globo) especialmente si nos encontramos fuera de nuestro hogar. Igualmente se podría notificar apagado de calefacción. Estas notificaciones podrían activarse o…
-
Create a range extender or let us use a second bridge...
Having olny 1 bridge per house is a massive design flaw yet to be addressed by Tado. Unless you leave in a tiny house made of cardboard walls, the TRV wlll lose connection or burn batteries in only a matter I'd a couple of weeks. I live in a house across 3 floors, I really struggle with the range and can't have full…
-
Set Humidex instead temperature
It can be useful to have the option to set the perceived temperature instead only the normal temperature. In the high humidity zones temperature is not significant. It would be nice to trigger the air conditioning with your wireless control to decrease humidity.
-
Smart wall plug for underfloor heating pump
You offer nearly everything except a way to turn a underfloor heating pump on or off. My living room thermostat is connected to the underfloor heating, and to control the pump I have to set up a complicated process through Homey and a Z-Wave smart wall plug. It would be great to have a Tado smart wall plug which can be…
-
Tado app return to 0.1° granularity for setting manual temp
Very frustrated to find I have lost the ability to set a temp of 20.8° in the app. 20.5° too cool, 21° too warm - but those are the only options now. Why has this been changed?! It worked fine before!
-
Switch between rooms in graph nice
When in graph mode, one can change the date range with the ˅ symbol next to the date. It would be so much easier to switch between rooms if there was a ˅ next to the Room/Device name as well. Now I have to go back twice (first to the Room, then to the home screen) to select a new room and view the graph
-
Group rooms
Can you add a feature to group rooms (i.e. ground floor / first floor etc) to a cluster to be able to boost / switch off with one click.
-
[Released] Show the climate report in browser on tado.com
In the app on my iPhone I can see the heating history which is great, but I don't understand why I can't see this when I access my tado account on tado.com using a browser running on my desktop computer.
-
temperature adjusted at the radiator valves
If the temperature is adjusted at the radiator valves, that new temperature remains set until someone adjusts it again or until someone chooses to go to the schedule at the next schedule change. I would like to be able to decide myself via the setting what the reaction should be when turning the radiator valves. In my…
-
Humidity visualization and routine with modality home, away
It would be useful to have an indication of the humidity directly on the room box to have an immediate idea of the environmental well-being. Also on the environmental well-being box to have a summary of the situation without clicking on it. It would be useful to have the possibility of programming the "home" or "away"…
-
Different Scenarios for Heating Schedules
Loving the Tado (but hating the 10 room limit) and I would like to make a heating scenario suggestion. This is to allow simple, perhaps temporary, changes to the heating schedule according to a set programme based on scenarios. The current way of working is to set up one scenario of daily heating and any changes require…
-
[Released with tado° X] Integration for Samsung SmartThings
It would be great if we Tado users could connect Tado to Samsung SmartThings
-
[Released with tado° X] Make the Smart Radiator Valves quieter
I find the Tado Smart Radiator Valves are too noisy for use in bedrooms. The motor noise when opening/closing the valve is loud enough to disturb sleep. I have had to set my bedroom schedule in a way that ensures the bedroom heating will never turn on when we could be asleep, and so have to manually turn it on everytime I…