Active

Battery status Matter
Hello, when Tado X radiator thermostats are connected to HomeAssistant using Matter Addon they dont show battery status because its not sending any. The radiator thermostats are connected through other brand Thread Border router.
Give users access to the advanced configuration parameters
As most of us here will be aware, Tado has several advanced controls and configuration options that support are able to use to configure your devices when you contact them (cycle periods, minimum on/off times etc). Sadly these advanced options are hidden from users and the only way to access them is through support which…
Funzioni in app
1 ) Sarebbe utile integrare in app la possibilità di variare manualmente la temperatura di mandata dell'acqua. 2) Quando alla caldaia è collegata una sonda esterna utilizzare la temperatura letta da essa ( sicuramente più precisa ) per regolare la temperatura interna perchè i dati del meteo sono troppo generici e succede,…
Real window sensors from tado
We would like a real window / door sensor for the "window open function". The current detection of the open windows via the thermostats works so far quite well. However, we have discovered some problems. 1. In some rooms the detection of an open window does not work or does it too late (e.g. bathroom, room with balcony or…
Better support for Underfloor Heating
Hi, I would like to request better software support for underfloor heating systems in the Wired Thermostats when using relay mode. The modulation used by the Tado Wired Thermostates is not beneficial to my system because it tries to turn the UFH on and off repeatably when NOT calling for "full heat" (i.e. when calling for…
Pre-heat and early start for Tado X
Hello, Just bought the tado x System and I am a bit disappointed that the pre-heat and early start feature are missing. Are there any plans to implement those two features? Please implement those two features🙏 Thanks, Florian
Ability to rename device
When batteries are running low I get an email informing me that a particular device in a specific room has an issue. In some rooms I have 4 radiators. I then have to go round ‘blinking’ the stat multiple and watching all the stats in the room to find which one it is. it would be great to be able to rename or give a…
Enable eBUS support for Tado X Wireless receiver
The V3+ supports both eBUS and Opentherm however the newer product series X does not support eBUS. Please enable also eBUS support for the X series. I imagine since you have the code for V3+ in the firmware it could be refactored over for the X and with a firmware update it could work.
Reduce the comfort temperature range to 18-21°c
In the uk a room set for the comfort range of over 20°c can far exceed a comfortable temperature. I would suggest reducing this so my app doesn't think my house is cold all the time
[Energy IQ] Allow for new meter and continue entering meter readings
When replacing a meter, it becomes hard to continue entering meter readings as one has to add the last old meter reading to the new meter readings (and sometimes even subtract the first new meter reading from that number too). Under Energy IQ, provide a meter reset button, with for the date of changeover: ++ the first new…
Data export
Please allow download of chart data for each room. This would be most useful as a CSV file. Data available should include date/time, actual room temp, demand temp (what the heating has been set to), humidity, open window detection, etc. I would like to be able to analyse my own data, and be able to make easier comparisons…
Ability to schedule "one time" events
Currently you can define a schedule but sometimes I have the need to just schedule a one off session. For example, Friday I will be home earlier than usual so I want to have the temperature be 20 degrees at 13:00 with the end-time being the "next" change. Its nice if this is possible because Tado will then pre-heat…
"summer mode" to keep radiator valves open during summer
The problem is: If I connect all the smart radiator thermostats to my zone controller and I don't want to heat any room (because it is summer now) this results in all the radiators being 'closed' (or 'blocked'). This makes the total central heating system volume smaller (since the radiators are essentially cut off from the…
Support newer version of Worcester HT-BUS
I just upgraded from a worcester bosch greenstar cdi to a worcester bosch greenstar 8000 life. On my old boiler I could connect to the digital low voltage interface bus however the new boiler the ht-bus is not supported and I couldn't simply change over I had to rewire to the old relay style. The bus interface is better…
Summer mode
My son has a Netatmo system and during the summer, the connected valves calibrate every 2 weeks, even when the thermostat is off, so that the thermostatic heads do not get calcified or stuck (which may happen if the valve is fully closed for a couple months). With Tado, I need to take all my programming to put the valves…
Support one decimal place (0.1) for radiator valve temperatures in the Tado app
These devices appear to report their temperature at 1 decimal place of accuracy (I see it via the API in my Home Assistant integration) yet the Tado app only shows their temperature as integers. Can you please change this? I recognise this might be difficult on the device display itself but not in the app. I'd also like to…
Wireless Receiver status
I'd like to see some status on Wireless Receiver, which thermostat is activating, a diagram would be also good, I'd like to see what is the running time of my heater in a day, could be also an indication of which room/device started/use it. Also, in Home Assistant the status of the thermostat is "heat", never goes "off",…
Better Boost Options
I was pleased to see the boast function for the system but very disappointed that you can't select the temp (25 is way to high for my house), or select to just boost one room/trv. I find that I often want to boost a room for just 10mins, and only being able to boost for 30mins at 25 is wasteful and unnecessary. I see that…
Better explanation with regards to termination of the old thermostat wiring.
I have recently installed the V3+ system and everything went well with regards the installation. I could see all the devices on the app and all the test procedures passed on the Wireless Receiver. However, the heating and hot water would not work. I was convinced I had done everything correctly and was struggling to…
Guest mode
There could be an option for guest mode, which would use a different schedule.
Exclude rooms from the energy report
Is it possible to exclude the heating of certain rooms from the energy report? Because I have a room in my home where the heating is centralised (but it still has a Tado on the radiator) and it doesn't impact on my bill… And as it stands it impact my energy report because it is constantly on. Thanks in advance

Active

Discussion List