-
Schedule profiles
I have now had the tado system for nearly a week, and its certainly better than my old hive system. You guys have done a good job on it. However you (and every competitor) are missing what I believe is probably an important feature for many people, and I can say 100% would have made me choose to move to you years ago had…
-
Dedicated tile for boiler status on/off (same as hot water)
Im fairly new to Tado but one feature i've seen that is so blindly obvious i though i was doing something wrong. It would be great to have a tile on the app which shows if the wireless recevier is actively calling for heat. Similar to the "hot water on/off" tile. A boiler on/off tile. I know there are the ~~~ wavey lines…
-
Smart Global Off Time with Conditional Notifications
Overview: I’d like to propose a feature that allows users to set a "Global Off Time"—a hard cutoff time at which all heating devices in the system are turned off or reverted to a predefined safe state (e.g., frost protection). This feature would address the issue of unexpected heating events during the night, offering…
-
Ability to rename device
When batteries are running low I get an email informing me that a particular device in a specific room has an issue. In some rooms I have 4 radiators. I then have to go round ‘blinking’ the stat multiple and watching all the stats in the room to find which one it is. it would be great to be able to rename or give a…
-
Offline notification
My Internet Bridge went off-line and I didn't realise for hours. A simple reset was all it took to fix the issue, which I could have done way sooner if I'd realised. Tado sends other notifications, like a thermostat needing batteries. I would like Tado to send me a notification, either push-notification in the app, or…
-
Worcester Bosch 4000 ems control
Please enable support of EMS / Ebus functionality so Tado can control modulation of this boiler
-
Tado feature request: 8-10 degree C mode support
Hi, I have 2 Tado AC controllers. I have been pretty happy with the one in our house, and purchased a 2nd one last week for our summer cottage. We recently installed a new Panasonic AC-model in the cottage, and during the winter, the AC is set to 8 degrees C to keep the house dry and frost free. I assumed that Tado would…
-
Pre-heat and early start for Tado X
Hello, Just bought the tado x System and I am a bit disappointed that the pre-heat and early start feature are missing. Are there any plans to implement those two features? Please implement those two features🙏 Thanks, Florian
-
Provide method to specify type of heating system, i.e. radiators, underfloor, etc.
There is no facility to specify what type of heating system is installed. It appears Tado treats all systems as if the heating system is based on radiators. In case of a underfloor only system it is likely the floor is cold when the first call for heat after a break is generated. Currently the system would start to run for…
-
3rd party temperature sensor support or cheaper add-on temperature sensor
I have multiple tado radiator thermostats, but all of them are a couple of degrees out with the actual temperature. I use an Aqara temperature sensor to measure the actual temperature in the room, further away from my radiator. It would be great if the tado app could use the data of these aqara sensors to measure the…
-
allow changing the name of devices
Please allow us to change the names of devices to make it easier to identify them. For example, getting an email that tells me: "We have noticed that the batteries in your Smart Radiator Thermostat VA*******048 in the zone ****** are running low." I have 15 devices and if each device had a name I wouldn't have to waste…
-
Notificación al móvil en caso de encendido/apagado de calefacción
Una sencilla forma de saber si se ha puesto en marcha la calefacción en nuestra casa (o en una estancia de ella) a través de una notificación al móvil (tira o globo) especialmente si nos encontramos fuera de nuestro hogar. Igualmente se podría notificar apagado de calefacción. Estas notificaciones podrían activarse o…
-
Setup modulation for underfloor heating
Hello, I have underfloor heating in my family house and have set a constant temperature of 22.5°C on the Tado V3 thermostat. Last night, the outdoor temperature was 2°C. At 1:15 am, the indoor temperature dropped to 22.5°C, and Tado started heating at the lowest level (one bar). It continued to heat at one bar from 1:15 am…
-
Create a range extender or let us use a second bridge...
Having olny 1 bridge per house is a massive design flaw yet to be addressed by Tado. Unless you leave in a tiny house made of cardboard walls, the TRV wlll lose connection or burn batteries in only a matter I'd a couple of weeks. I live in a house across 3 floors, I really struggle with the range and can't have full…
-
Set Humidex instead temperature
It can be useful to have the option to set the perceived temperature instead only the normal temperature. In the high humidity zones temperature is not significant. It would be nice to trigger the air conditioning with your wireless control to decrease humidity.
-
Smart wall plug for underfloor heating pump
You offer nearly everything except a way to turn a underfloor heating pump on or off. My living room thermostat is connected to the underfloor heating, and to control the pump I have to set up a complicated process through Homey and a Z-Wave smart wall plug. It would be great to have a Tado smart wall plug which can be…
-
Tado app return to 0.1° granularity for setting manual temp
Very frustrated to find I have lost the ability to set a temp of 20.8° in the app. 20.5° too cool, 21° too warm - but those are the only options now. Why has this been changed?! It worked fine before!