-
Swipe to switch between rooms
Or be able to change temperature from the view with all rooms.
-
TRV thermostats open without requesting heat for a back boiler stove
I have a back boiler stove that heats my radiators and hot water when we use it. - in addition to our burner Every time I do this, I have to unplug all the TRVs manually. My friends laugh at me because of this. Why is there not a mode to open the valves without requesting heat? This would also help with bleeding radiators…
-
Notification when the device triggers the heating to turn on
In the past the heating has been turned on even though it has not been manually activated and the scheduled times have not been triggered. Obviously when no one is in the house this becomes a major issue, particularly with the rising cost of fuel. Can you develop a notification that an email or app notification is sent…
-
Enable multiple smart schedules
During the week, we have various ways we want to smart schedule our radiators: If we're both in the office, then we don't want the heating on If I'm in the office, then we want the heating on but not in my partner's office If my partner's in the office, then we want the heating on but not in my office If we're both working…
-
Hot water not working? You need the room temperature sensor
I have just set up a tado system for my elderly mother. She has only 4 radiators and a hot water tank in a Y-plan configuration. I put smart TRVs on the radiators and they were working to plan, but the hot water did not work. The wifi receiver seemed to be refusing to configure to the Y-plan, reverting constantly to a…
-
Individual temperature settings
It would be really good if you could have temperature profiles for each person and then one for when there’s multiple people home. I have my schedule set up so my partner is t cold, but I always turn it down when she goes out and I’m home. It would be nice if taco would see I’m home alone and reduce it to the temperatures…
-
Lower hysteresis for underfloor heating
We have Tado controlling our underfloor heating but it has two issues: it's not learning and the hysteresis is too big. If I set the room to 20C then the underfloor heating doesn't come on until the temperature has dropped to 19C. It then runs the boiler until the room hits 20C but the residual heat in the floor keeps the…
-
Change the hysteresis / PID settings
Hi Tado. The current desire of the smart thermometer algorithm to track the set temperature is killing my hardware. It is turning it on/off so often that things are breaking (like TCVs). How about I can select the min and max settings that trigger a state change? Or if it is a PID system, I should be able to change the…
-
Heating Log
Would love to be able to view a log within the app of all the temperature changes and calls for heating on and off and date/time stamps.
-
Release a smaller, cheaper Wireless Temperature Sensor for the Smart Radiator Thermostats
The recently released "Tado Wireless Temperature Sensor" is essential, in many scenarios, to have accurate operation of the Tado Smart Radiator Thermostats. Which, due to their proximity to the radiator, are not typically able to measure the actual room temperature themselves. However, many find the price (£69.99 / 79,99€)…
-
Update for the TRV Compatibility CHart - Landis & Gyr
The TRV compatibility chart only has one type of clamp on Landis & Gyr TRV that is not compatible with Tado V3+ smart valves. My Landis & Gyr TRV heads have the standard 30 x 1.5mm screw fitting so the Tado valves fitted without any adapters. I have attached photos of the valve body and TRV cap.
-
[Released] Finer granularity of temperature reporting and adjustment for Smart Radiator Thermostats
Throughout the app temperatures are reported and set in units of whole degrees. It would be beneficial to increase the granularity of both reporting and setting to half degree increments.
-
Better overview of all schedules in one view
I’d find it really useful to have an overview of all the schedules of my smart valves so I can see when the heating generally kicks on and off to be able to review my system more efficiently. At the moment I have to check every valve individually just to see I’m when everything turns off and on in order to refine my setup
-
Smart Schedule overview for all thermostats
It would be great if you could see something like this in the Tado app… See attached example/picture….
-
'Boost' Function should work by zone
I have 3 floors to my house and 3 wireless receivers on my boiler. Every radiator has a Tado X TRV on it. Occasionally we like to boost the heating, but we are only ever normally on 1 floor. During the day, if I want to boost the heating downstairs, by pressing 'boost' every single radiator across 3 floors comes on, making…
-
Rename Zone Controllers / Wireless Receivers
We should have the ability to rename the wireless receivers and give them proper zone names. I have 3 wireless receivers on my boiler for 3 floors in my house. When I add a new temp sensor or radiator TRV, I should be able to add it to 'downstairs' or 'basement' or 'upstairs'. Not to PR123456789! I installed all three…
-
OpenTherm Min Flow Temperature
My boiler is set to OpenTherm mode, with Tado V3+, and the maximum temperature is set to 55°C. Tado adjusts the heating temperature based on the outside weather, which works fine. However, I have a question about the minimum temperature: I’ve noticed that the boiler pump runs frequently, circulating water at 20–25°C. While…
-
[Released with Offline Schedule] Offline notification
Note from tado°: With tado°'s Offline Schedule (requested on the community for V3+ and always available for tado° X), a text block appears in the app confirming tado° is offline. This is not a notification, but it is a way to inform users when this occurs. Original Post: My Internet Bridge went off-line and I didn't…