-
Support current and more recent Vaillant eBus controllers
Tado asserts the benefits of modulating boiler control and touts compatibility with Valiant and eBus. However, the reality is rather grim. It turns out that as of 2019-03 eBus is only supported in these scenarios using the now discontinued VR65 controller. No other controllers are supported (VR66 for example). This means…
-
Battery status Matter
Hello, when Tado X radiator thermostats are connected to HomeAssistant using Matter Addon they dont show battery status because its not sending any. The radiator thermostats are connected through other brand Thread Border router.
-
Give users access to the advanced configuration parameters
As most of us here will be aware, Tado has several advanced controls and configuration options that support are able to use to configure your devices when you contact them (cycle periods, minimum on/off times etc). Sadly these advanced options are hidden from users and the only way to access them is through support which…
-
Heat request light blinking / slowly fading in and out in relay mode
I rewired my tado to relaay mode from digital mode as digital mode was not working. However seems like my device is still set to digital mode as my Heat request light is blinking / slowly fading in and out and not a solid on. How do I force my device to relay mode? As per tado - When tado° is requesting heat, the heat…
-
Ability to rename device
When batteries are running low I get an email informing me that a particular device in a specific room has an issue. In some rooms I have 4 radiators. I then have to go round ‘blinking’ the stat multiple and watching all the stats in the room to find which one it is. it would be great to be able to rename or give a…
-
Suggestion for Tado App: Ability to rename "Other Devices"
A suggestion for the next Tado app update from my side would be the ability to rename the individual Tado X Bridges and Tado X Receivers in the same way it is possible with the Smart Thermostats. Since i have two bridges and 6 Wireless Receivers (multizone setup) it gets tricky to know which one is which one without having…
-
Support for the EMS2 bus - Bosch Condens
Bosch / Junkers / Nefit boilers with the EMS2 bus have been on the market for many years now, have a large chunk of the European market share but Tado only supports relay operation for them. I myself have a Condens 2300i boiler and while the relay mode works up to a point, the TPI algorithm operating the relay can't avoid…
-
Firmware update to include EMS2 support
Having upgraded my boiler to a greenstar 4000 30kW, I am disappointed to find out that tado cannot connect digitally, only via relay. There will be a lot of customers facing the same issue and this should be set as a priority to be resolved as I can’t imagine a firmware update to include the new language being too…
-
Worcester Bosch EMS2
It appears Tado is able to work with older Worcester Bosch Boilers with HT-EMS. Possibly some others Bosch ones with EMS+ ? It will also work on Relay (R01), On/Off Mode, but this will NOT modulate the boiler. All new boiler installations in the uk have to confirm to EnergyPlus Regulations. This means having some of…
-
Apple Watch App for heating control
Hi Tado team, I‘ve been a customer of yours for years and I‘m grateful for the energy savings we‘ve been able to make. I have one suggestion… I have been waiting all these years to be able to control the temperature of my heating via my Apple Watch. Please release a watch app, this would make things SO much easier!
-
Wifi geofencing
It would be good if there was WiFi only geofencing. There is not point to keep GPS up whole day and drain battery. I know it would limit app to on and off rather than vicinity check but there is few benefits for me from GPS geofencing as home members keep turning GPS off to save battery life thus geofencing do not work as…
-
I would be thrilled if you could enable the following integrations for TadoX:
Offset Adjustment via Matter: It would be incredibly helpful to allow offset calibration directly through Matter. Display Temperature from an External Sensor: Enable the TadoX device itself to show the temperature measured by an external sensor, which would greatly enhance usability. Use of Any Temperature Sensors via…
-
Add NOK as a currency
Whilst GBP and Euro cover most countries, add NOK would cover Norway, Sweden and Denmark. Tado is available for sale in these countries.
-
Tuile eau chaude sanitaire
Est-il possible de supprimer la tuile ECS quand on n’à plus de ballon ECS commandé par la PAC
-
Push notify users when there is evidence that the boiler/heat source isnt doing its job
It is a common problem for oil fired boilers, particularly those over 10 years old, to be heavily affected by wind speeds near the air intake. A sudden rise in windspeed, occuring within 1 meter of the air intake can cause the boiler's air mass sensor to misread the temperature and volume of air incoming and force the…
-
Naming controllers
I would like to name my radiator controllers. Currently they are all numbers in the app. But I would like to give them a name e.g. "living_front-left", so I know which one needs batteries. Now I have to check all.
-
Manual Control on tado° device doesn't work.
This used to work, now it doesn't. Timer set to 20 min. Heating on via manual mode. Schedule set to infinity, but should be to 20 min. Also, the app doesn't remember the last state, so every manual setup starts from 'until you resume' mode. ¯\\\_(ツ)\_/¯ Please can this be checked & confirmed if a bug or a feature?
-
Switch off schedule for individual rooms . . .
The current schedule system provides a "switch off all rooms" feature. This is useful but it would be even better if rooms could be switched off individually. At the moment the only way to remove a room from the schedule, without resorting to "switch off all rooms" is to go to each room's schedule and switch off the…
-
Tado App Privacy
All home users and their email addresses are visible to any user in the home. I would like to be able to hide the details of guests from other guests
-
Hot water command
Hi, I'm a user of tado thermostat cabled with a radiant r2k heater. As some other Italian users we have an issue with domestic hot water when the thermostat is cabled with opentherm configuration. When the thermostat work as heating the domestic hot water works too. But when the thermostat reach the temperature set, the…
-
Multiple accounts in 1 Tado App
Being a fan of Tado, I introduced to both my kids and mother in law. My mother in law needs some assistance, and in case, I can have the control from my home. But needed an other divice, because it's not possible to have 2 accounts on the same app. Is it possible to add multiple accouts / living address to 1 app on 1…