-
Tado X Wireless Install - hot water works, but not heating
Hello all, I have just installed a Tado X wireless thermostat and only the hot water function seems to be working - I have no heating working. I have a conventional Bosch Greenstar 24i System mkIV boiler with a hot water tank in the loft. I have had/have Horstmann Centaurplus C27 series 2 programmer, and a horstmann…
-
Added VR33 to EcoTech Plus 937 and radiators heating all the time.
I have been running my EcoTech Plus 937 using eBUS from an Extension Kit for a couple of years without problem - apart from signal strength to TRVs. About to take the plunge on the Tado X discount offer but before spending nearly a grand I wanted to make sure I could still run the boiler with modulation so I ordered the…
-
Issues with eBUS (Vaillant) support and Tado X
Hello everyone, I recently upgraded to the Tado X Wireless Thermostat, but I'm facing some issues with my Vaillant ecotec plus (vcw296) boiler. This boiler uses the Vaillant eBus protocol. My previous Tado V3 model supported modulation via eBus, but after connecting the new Tado X in the same way, it doesn't seem to work.…
-
tado X , Homey Pro and Hot Water flow cards
Hi, Can anyone point me to details on controlling hot water via a Homey Pro with flow cards? I can only see two cards; both look like heating rather than hot water-related to me. Set the Mode (Automatic, Heat, Cool, Off) Set the temperature Has anyone cracked this? If so, or if you haven't but know the answer anyway, your…
-
Can't add Tado X devices to Google Home
Hi everyone, I just installed Tado X and I have added all thermostats to the tado App. However I can't add them to Google home when following tado X official instructions (https://help.tado.com/en/articles/9184568-how-can-i-set-up-my-tado-x-devices-with-google-home): In the tado° app: Open the tado° app. Select Settings >…
-
System boiler with Opentherm PDHW - X PLAN
I want to know if people are using Tado X with opentherm on a system boiler and tank using opentherm? from my understanding this needs to be configured as PDHW. If you have this type of setup work I would love to see what you have and how well this is working.
-
Tado x thermostat required?
Hi all! Wondering whether i can have Tado x without a wall thermostat, i.e. just the rad valves, a receiver next to the boiler and a bridge to control online/via app? Thanks
-
Tado X pairing connection Wireless Smart Thermostat X - Starter Kit
Hello there, I have the following problem. I just bought a Tado X Wireless Smart Thermostat X - Starter Kit The problems are the following: The Wireless Receiver X did connect with my wifi without any major problem (even if i needed 4-5 attempts). The Wireless Temperature Sensor X is not able to pair with my phone and…
-
Tado X support for hot water?
I currently have a Nest controlling the radiators and hot water, and a Drayton programmer controlling 3 zones of underfloor heating. Both demand from the gas boiler independently. I think I’ve worked out that the V3+ supports this configuration with a wireless receiver and 3 wired thermostats. But am I right in thinking…
-
Tado X wiring setup
Hi all, We recently received a Wireless Smart Thermostat X - Starter Kit and two Wired Smart Thermostat X. The previous system had 3 zones, 1 Hot Water Cyclinder Zone and 2 Central Heating Zones. The old programmer (ThermaQ TQX0027, also known as ESi ES3247B) controlled these zones. The old thermostats are ThermaQ branded…
-
Tado X wireless receiver connection with Honeywell VC4013 two way valve
I want to connect Tado X wireless receiver to a zone valve - Honeywell VC4013. This is a two way valve. The wireless receiver will open/ close this valve on demand from the Tado X wireless room thermostat. Can someone guide on the connections from the VC4013 to the Tado X receiver. Should the sensor wires of VC4013 be…
-
Tado X TRV not causing a heat call
Hi, I've recently bought 2 X TRVs and a thermostat, and an x bridge. One trv and the thermostat are located in the bathroom, the second trv is in the bedroom. When I set the temperature target in both bathroom and bedroom to a higer temperature than the actual temperature the thermostat does a heat call to the boiler.…
-
All Tado X devices disconnected
Hi all, I upgraded from a Google Nest thermostat to a Tado X earlier in December and since the change I kind of had to battle with this system in a way or the other and I see in the forum I'm not the only (not sure if this is actually comforting). Anyway, after buying the second Bridge X I managed to have all the TRVs…
-
smart radiator thermostat X with straight joint (frontal screen)
Can you please consider designing the smart radiator thermostat X with a straight joint, as an alternate option to the current T joint? The T joint does not work well with modern radiators, which have the valves pointing "frontally", thus resulting in the screen of the knob pointing either downwards/upwards or to the…
-
Announcement: Flow Temperature Optimization now available for V generations and tado° X (OpenTherm)
Hello community, We are pleased to announce the release of a new Flow Temperature Optimization feature for tado° customers with V2, V3, V3+, and X devices directly connected to a boiler or heat source. Flow Temperature Optimization at a glance With Flow Temperature Optimization, you can avoid overheating your central…
-
tado° X Upgrade Offers
Hello community, Since last week, eligible customers in the UK should have received their tado° X upgrade offers by email. Eligible customers were those for whom the upgrade was technically feasible, who were with tado° for a defined amount of time, who were subscribed to the newsletter. Please use this thread to let us…
-
Improvements required to Tado heating logic in relay mode.
Hello again all! As users of Tado in a relay setup (no OpenTherm/no external modulation) will be acutely aware, Tado's default heating logic suffers from severe short cycling issues where Tado will fire the boiler for only a couple of minutes at a time in short succession, behaviour that has brought many of us here to…
-
Boiler Actual On/Off Status
Hi, Would it be possible to provide an actual indication on when the boiler is switched on/off by Tado, please? Currently there is no clear indication on graphs/in the app as to when the boiler is requested to operate. This would be really useful to have and should be easy to implement.
-
Tado° V3 vs. X series compatibility concerns
Hi everyone, I’ve been using the Tado° V3 range (thermostat and smart radiator valves) throughout my house for about 2 years. Recently, one device broke, and when I ordered a replacement, I discovered there's a new X series, which isn’t compatible with my V3 setup. Does this mean that once the V3 devices are discontinued,…