-
V3+ users can now request Offline Schedule
Dear community, We are happy to announce that, as part of our ongoing tiered rollout, the V3+ Offline Smart Schedule is being made available to interested tado° users via the community forum. Due to compatibility considerations, this offer is only available to community members with V3+ heating starter kits or add-on…
-
Weird goings-on this morning – App/Internet Bridge/Smart thermostat - what's happened?
Got down for breakfast to find the room a bit chilly. Checked the app to find the dining room online but all other rooms offline. How can that be? Changing the temperature in the app had no effect so went to the main, smart thermostat. Upped the temperature manually and the heating came on. But the thermostat showed low…
-
Hot Water Turned On Outside of Schedule
Hi Everyone I have just completed my Tado Wireless V3+ Installation with the bridge, wireless thermostat, wireless receiver and 5 TRVs. I followed the installation settings exactly. I have a Y-Plan system with a heat only boiler and a Hot Water cylinder. The HW cylinder has with a Cylinder Thermostat which is set to 65c.…
-
Short-cycling boiler, any fixes?
No responses to my previous "New/Old system" query, so I must therefore assume what I am experiencing is 'normal' behaviour. I will try to learn to accept the wildly inaccurate timer switching. So I will ask another question, assuming again if there are no responses, it is again, 'normal' behaviour for Tado: *I turned on…
-
Heating randomly stays on and exclamation mark present!
My Tado V3+ system and TRVs have been fitted for 3 months with no problems. However, on a couple of occasions the central heating will remain on past the thermostat set temperature. The heating then remains on no matter what I do, unless I hard reset the Tado sender unit in the airing cupboard. I also notice that the…
-
New/Old system problem
I've just bought a complete system from a neighbour who gave up on it. I got it for a song, but I am having an issue with it. I bought it and set it up a while back, can't remember exactly when (maybe 8 weeks), but I did so because I'm going away for a couple of weeks and wanted to set a couple of rooms to stay at a set…
-
CALDAIA IMMERGAS VICTRIX TERA V2 28kw
Vorrei capire se posso collegare tado v3+ alla mia caldaia immergas victrix tera v2 28kw in modalita di modulazione utilizzando le uscite digitali OT (opentherm). l'assistenza Tado dice di no ma qualcuno sembra esserci riuscito.
-
V1 Installtion
Hi I have the original V1 beta which I have not used since probably 2019. I powered it up today and it said all components were offline. I then deleted the home so that I can add everything back again. But it's asking for the serial number and 4-11 digit code. I have the serial number but where do I find the code?
-
Altantic Boiller and Tado wiring
Hi everyone, I'm in the process of replacing my old thermostat with a wired Tado V3, but I'm running into an issue. The old thermostat had just two wires connected to it, and following the manual instructions, I connected these to the + and - terminals on the Tado (on the right-hand side) and set the correct settings…
-
Thermostat Receiver not communicating with boiler
Hi there, we had a danfoss receiver installed previously and we replaced it with Tado. We followed the same wiring based on how the danfoss was wired and for a couple of days it was working fine. After 2-3 days the Tado stopped communicating with the boiler and now when we boost the heating on the app or turn on the…
-
Need help with tado°
I'd like to describe my newest experience with Tado support. I have some problems with hot domestic water - it gets heated to too high temperature. What feedback I got from Tado representative: "That may be the reason the OT connection is not fully compatible. An installation tado° Smart Thermostat directly to your boiler…
-
Maximum flow temperature per smart thermostat
Please enable setting max flow temperature per smart thermostat, not per whole central heating system. When smart thermostat controlling underfloor heating calls for heat alone (radiators don't ask for heat) there is no need to heat the system so high. A lot of users have mixed systems (ufh + radiators) so it would be…
-
Collegamente IMMERGAS VICTRIX TERA V2 28kw con Tado
Volevo capire se è possibile collegare la mia caldaia IMMERGAS VICTRIX TERA V2 28kw a sistema Tado V3+ mendiante uscite digitali OT Opentherm e quindi in modulazione.
-
Announcement: Flow Temperature Optimization now available for V generations and tado° X (OpenTherm)
Hello community, We are pleased to announce the release of a new Flow Temperature Optimization feature for tado° customers with V2, V3, V3+, and X devices directly connected to a boiler or heat source. Flow Temperature Optimization at a glance With Flow Temperature Optimization, you can avoid overheating your central…
-
Energy IQ update...
Hi, so Energy IQ was pretty good when I started with Tado (4 years or so?). It then went lottery mode where it would just show nonsense. Has anyone else noticed them fixing it? The December numbers are within 80 kWh! That is pretty impressive…
-
Baxi System 100he boiler
I'm thinking of buying Tado V3+ Wireless Heating & Hot Water Smart Thermostat Starter Kit and Smart radiator valves. Does anyone know if they are compatible?
-
Tado won't talk to boiler. I'm cold and losing the will to live...
It's like a loveless marriage, they've fallen out after four years and will no longer speak to each other, just sitting there will folded arms refusing to budge. Go easy… I'm not an electrician or a plumber but have had both of these people (both trusted people who I know) out to try and fix this issue without success.…