-
Announcement: Flow Temperature Optimization now available for V generations and tado° X (OpenTherm)
Hello community, We are pleased to announce the release of a new Flow Temperature Optimization feature for tado° customers with V2, V3, V3+, and X devices directly connected to a boiler or heat source. Flow Temperature Optimization at a glance With Flow Temperature Optimization, you can avoid overheating your central…
-
2 zone CH and hotwater
I was initially advised by the Tado bot that it was possible to install two V3+ wireless starter kits in my home. Following that advice, I installed: 1 bridge 2 wireless receivers 2 wireless thermostats 8 smart TRVs While everything seemed to work fine at first, I’ve noticed that the receiver controlling the hot water and…
-
Improvements required to Tado heating logic in relay mode.
Hello again all! As users of Tado in a relay setup (no OpenTherm/no external modulation) will be acutely aware, Tado's default heating logic suffers from severe short cycling issues where Tado will fire the boiler for only a couple of minutes at a time in short succession, behaviour that has brought many of us here to…
-
Boiler Actual On/Off Status
Hi, Would it be possible to provide an actual indication on when the boiler is switched on/off by Tado, please? Currently there is no clear indication on graphs/in the app as to when the boiler is requested to operate. This would be really useful to have and should be easy to implement.
-
Tado° V3 vs. X series compatibility concerns
Hi everyone, I’ve been using the Tado° V3 range (thermostat and smart radiator valves) throughout my house for about 2 years. Recently, one device broke, and when I ordered a replacement, I discovered there's a new X series, which isn’t compatible with my V3 setup. Does this mean that once the V3 devices are discontinued,…
-
Tado App Crashing
Hey, Does anyone else experience issues with Tado app this morning? It says that "connecting to the serves has failed. Please check your internet connection" and I was also getting messages 'Error- internal.server.error" I get same error messages when trying to access the system via desktop web browser too. Was hoping to…
-
CALDAIA IMMERGAS VICTRIX TERA V2 28kw
Vorrei capire se posso collegare tado v3+ alla mia caldaia immergas victrix tera v2 28kw in modalita di modulazione utilizzando le uscite digitali OT (opentherm). l'assistenza Tado dice di no ma qualcuno sembra esserci riuscito.
-
AI based scheduling assistant
I find setting up the schedules a little bit clunky as I have 8 thermostats to set up so I wondered whether there was scope to instead have the app ask you a few questions and then set up the schedule for you. Such as it could start with asking a series of questions about which room do you sleep in. What time do you get up…
-
V3+ users can now request Offline Schedule
Dear community, We are happy to announce that, as part of our ongoing tiered rollout, the V3+ Offline Smart Schedule is being made available to interested tado° users via the community forum. Due to compatibility considerations, this offer is only available to community members with V3+ heating starter kits or add-on…
-
Smart Thermostat Touch Buttons issues
I was having all kinds of issues with the touch buttons but now it getting worse. Sometimes they work properly while other times they seem to get stuck, for example when I want to reduce or increase the temperature by pressing once, it seems as if I keep pressing it and it goes to OFF or 25 respectively. The problem is…
-
TADO X without Tado App/Bridge/Cloud...
Hello community… Assuming that I have a thread border router already, and have a home automation controller that speaks matter. (In this case, a Home Assistant Yello). Can I just add a Tado X device to that, and use it without needing the Tado app/Cloud? Asking because if this works this would offer a migration path from…
-
What additional Tado kit do I need to add control for a single wet UFH zone?
Hi. My house is currently set up as follows: Combi boiler for all central heating (and hot water). I have the 'Wireless Smart Thermostat Starter Kit V3+ with Hot Water Control' setup to run the central heating. We don't use the hot water control but needed this setup as the thermostat is not wired to the boiler. Let's call…
-
Early Start learning (Tado V3+)
We have a room which takes over 3 hours to heat up if the outside temp is below 2C and then it may not hit target in that time. Here in the UK during the recent very cold weather, I have been boosting the room heating with a fan heater for an hour or so to get the room up to temp, then the radiators are able to maintain…
-
Weird goings-on this morning – App/Internet Bridge/Smart thermostat - what's happened?
Got down for breakfast to find the room a bit chilly. Checked the app to find the dining room online but all other rooms offline. How can that be? Changing the temperature in the app had no effect so went to the main, smart thermostat. Upped the temperature manually and the heating came on. But the thermostat showed low…
-
Boost Heating - Timeframe Options
When selecting Boost All Radiators, it would be helpful to allow this to be configured to a timeframe of your choice. Pre-defined options like +30mins, +45mins, +1hr etc could even be options further along the side scroll where you can find the current options.
-
V3smart radiator valve
The piston on my themostat was not conected to the theaded drive shaft any suggestion on how to get it back on the threaded shaft?
-
Add humidity in the tiles
The current tiles have enough room to add more information like humidity. Additionally you could a a toggle in the settings to toggle on/off certain displays.
-
TRV going into manual mode all on its own.
When I go out for a while I set the system into 'away' mode and all eight TRVs go into frost protection mode. A while later (variable) one of them (always the same one) goes into manual override mode and turns that room back on. This is clear when the temperature graph for the room is examined. No one is in the house to…
-
Individual Room Boost Request
Hey, Would it be possible to implement a solution, where heating for an individual room only could be boosted? Currently, this is missing from the app, as you can only hit a button to boost all rooms at once and then you have to untick the ones that you are not interested in. Which is a bit cumbersome. The only tweak I…
-
Help adding a TRV to a 2 zone tado system?
We have our heating set into 2 zones (upstairs & downstairs) and have been using tado for a few months controlling the 2 zones independently which was working fine. I recently tried to add a tado smart radiator thermostat to add more control to one individual room upstairs and have been having issues. Our original set up…