-
chaudière en sécurité
bonjour. ma chaudière électrique ortli cer s'est mise en sécurité car il n'y avait plus assez de pression dans le circuit d'eau ( circuit avec radiateur). le thermostat v3+ ne m'a jamais prévenu que la chaudière ne chauffait plus ni même que la chaudière se trouvait en sécurité. Serait-il possible que l'appli ou le…
-
Geen functie/symbool gebruik warm kraanwater op thermostaat
Volgens bijgaand artikel van support heeft de slimme thermostaat een symbool voor warm water productie. https://support.tado.com/nl/articles/3387237-wat-betekenen-de-symbolen-op-het-display-van-de-slimme-thermostaat-of-de-draadloze-temperatuursensor Op mijn (recent geplaatste) thermostaat krijg ik dit echter niet op mijn…
-
Avoiding sticking pins in thermostatic radiator valves
The pins in TRVs often stick in the closed position if the valve is left closed too long - such as over summer. Pre-Tado, I used to open the valves fully for the summer so that the first action at the start of the heating season was to force the pin down rather than rely on the spring to open it up. This avoids the…
-
Support for multi-zone UFH manifolds
The current integration with underfloor systems appears to be limited to single zone systems without zone actuators. A lot of UFH system are UFH downstairs with radiators upstairs. The UFH system typically have more than one zone with actuators per zone and a shared pump. Currently, I can get a multi-zone UFH management…
-
Black or Anthracite thermostat
Are there any plans to bring out a black or anthracite grey colour for the actual thermostats. I am fitting three anthracite radiators into a new kitchen and would prefer a more suitable colour than white.
-
New development idea - define a maximum upper temperature
Hi, I like very much your products and have 2 of your thermostats installed in my house. But there is one functionality I really miss ..., hence this note. You probably already thought about it but just in case, here you go: within current context of very expensive energy you certainly have customers willing to LIMIT the…
-
Humidity notification
Tado keeps also track of humidity percentage in the room, it would be useful to receive a notification when it reaches a certain percentage so that I can open the windows and clear some hair.
-
Boiler Switch On Activity
Having several rooms disconnected (independent) from the boiler it's not possible to know which room has activated the boiler and for how long. Just like the report for each room showing the heating statistics, it would be great to has the same for the boiler. It would show what time the boiler switched on and off, and…
-
More than one tariff rate in energy IQ
Would it be so difficult to have more than one tariff rate? I have 2 tariff rates. One rate for the first 2kwh and another for the rest over 2kwh. So the costs costs shown in energy iq are not accurate at all.
-
Bridge connectivity
As with many people on the forum, I have had connectivity issues in a house with the router and bridge at one end of the house. In the end, I had to return some sensors back to a non TADO alternative. I have just found that a tp-link powerline adaptor AV 1000, would allow the bridge to be connected remotely to the router.…
-
Worcester Bosch digital connection for 2000/4000/8000 series boilers
New wireless controller; https://uk.installers-shop.tado.com/products/wireless-smart-thermostat-starter-kit-v3-eu-version can you please add EBUS communication with the combi/system boilers to support modulation, since these are one of the most popular boilers available in the UK with modulation its stupid not to have the…
-
Boost heating until custom temperature is met
Hi, I would like to suggest a custom feature that. Currently when you boost heating it keeps going until the temp hits 25 or is turned off. I suggest you should be able to boost the temperature to a custom defined temp such as 21 or 22 degrees. Many thanks Neil
-
User configuration of "Early Start"
It would be good, if WE could set how long it takes for OUR ROOMS to heat by 1˚c (each room should have it own setting), then early start may actually be useful. Time to heat by 1˚c: 0hrs 30mins So if the room has a target temperature of 19˚c, and the current temperature is 16˚c, early start would kick in 1 hr 30 mins…
-
Heat hot water on return home
Idea: I have my hot water set to heat 2x per day - 1 in morning and 1 in afternoon Sometimes I’m out in the afternoon when my water is scheduled to heat. An awesome feature would be, if I’m out when the schedule block occurs, and geo fencing means my water is turned off, when I return home again the water should be heated…