-
Smart AC & Smart Thermostat/Radiator integration
Hey, I am using Thermostat and Smart Radiator since my house has central heating, but for cooling reasons I need to install two AC's LG Split, more to cool than heating because I already have a central heating system. I am thinking of adding Smart AC Control to my Tado System so that I can integrate everyone on the same…
-
Customize the main screen
Add more options for a customized look. display humidity
-
dynamic offset to cure TRV inaccuracy
It's well known that TRVs are accurate for room temperature when the radiator is off, but inaccurate when the radiator is on. I'd like Tado to implement a feature where the user can set a dynamic offset, such that when the radiator is on the room temperature is offset by -9/+9 degrees. Should minimise the TRV temp problem.…
-
More rooms for extension kits
Tried to add a room to extension kit but limit is 10 rooms I cannot have more than 1 extension kit so I am restricted to a maximum 10 rooms can the limit on amount of rooms be increased for extension kit?
-
See which room is calling for heat on home page
You can see which room is calling for heat by going in to the room and seeing the wavey lines, but on the main home page, there is no clear indicator as for which room is calling for heat - just a colour indicator for 19 degrees and above (yellow) 18.9 and below (green). This can actually confuse things as yellow could…
-
Make Quick Actions more specific
I like the idea of the Quick Actions although the boost action would be much better and more useful if it were to be applied only to the rooms that are actively heating in the schedule at the time the boost is applied. I don’t want to be boosting the whole house when I’m only using the lounge or downstairs. Can this be…
-
Manual control - Turn-all-on/off (boost) timer - Away Mode timer/datePicker
I quite liked your Turn-all-on/off feature, but I am missing a specified time - the same way as if you manually set a temperature to a room, so for example 2h, 5m... Also the same way with the manual AwayMode - there it would be usefull a calender/dateTime picker. Thanks! Jaroslav
-
Notification when heat is turned back on automaticly
Hi. There is the feature where you'll get a notification if there's an open window and then you can click the "turn of heat", the heat stays of for a period of time and then on. My request is a feature that makes it possible to get a notification when the heat then turns on again - so that I know to close windows/the heat…
-
Support for multiple people and multiple zones
With current geofencing, if all devices are away from home all zones are set to away. If at least one device is at home, all zones are set to home. Ideally, this should be more granular. As an example: We have two devices, mine and my partners. We have four zones: my study, my partner's study, a shared bedroom and a shared…
-
Need a meter for hours heating was on
Living in a block of 8 flats, we all tap on central petrol heating. We get charged by the hours we have heating on. No information In the daily room graph (have only one thermostat) there is no indication of the time heating was actually on, from start of month / from start of day till present. Is something so obviously…
-
Oventrop 1011450 - Bulk Purchase
I am sure you are aware that the above elbow adapter is proving a success for the few using them. How about you arranging a bulk purchase from the German Firm in order that we may buy from you? For anyone who has not read the thread on this, the above link for Amazon shows the adapter which turns an upright tado TRV into…
-
Changing the maximum flow temperature myself
Initial problem: Hello, i have a Ferroli Bluehelix PRO 32C heating central. I use tado for 3 years now. After last update of Tado APP to version 6.0.2 (9826) i found following bug. I limit maximum temperature of heating using heating buttons on my boiler to 55C. After this update, maximum flow temperature is reseting…
-
VA03 Smart Radiator Thermostats support a charging port?
Will the next version of smart radiator thermostats include charging ports? Will make life a lot easier. I'm stuck with VA01's. Unless there is an introductory offer that I can't refuse I doubt if I'll change them. If I did I'd die happier if they had charging ports 😕⚰️😌
-
I'd like to suggest that tado's programmers think, before changing the app/web page
Prior to upgrading from V3+ to X, and a app update, I could tell which of the radiators in a room needed the battery changing by blinking the device. When I started the updated app with Tado X, and added a device it actually prompted me for a name for the device. I added "Back wall radiator" and "Side wall radiator". So…
-
device offline notification
It would be great to make a notification that the device is offline. Notification on the phone, sending an email, etc. Currently, the system status can only be found by opening the application. Thank you
-
Push notify users when there is evidence that the boiler/heat source isnt doing its job
It is a common problem for oil fired boilers, particularly those over 10 years old, to be heavily affected by wind speeds near the air intake. A sudden rise in windspeed, occuring within 1 meter of the air intake can cause the boiler's air mass sensor to misread the temperature and volume of air incoming and force the…
-
Rename Zone Controllers / Wireless Receivers
We should have the ability to rename the wireless receivers and give them proper zone names. I have 3 wireless receivers on my boiler for 3 floors in my house. When I add a new temp sensor or radiator TRV, I should be able to add it to 'downstairs' or 'basement' or 'upstairs'. Not to PR123456789! I installed all three…
-
Set a working temperature range
In the intelligent programming section there isn't the feature to set a minimum and a maximum temperarture. Currently, you can only set a maximum temperature above which the heating switches off and below which it switches on. It would be nice if you could set a minimum temperature below which the heating is activated and…
-
Local Mode option for Tado X
Reading the manuals it would seem that if a wireless temperature sensor goes offline, the controller will continue to heat as per the schedule. However, with the server issues the last couple of days I had the following; One Wireless receiver X controls one zone and hot water and was running a schedule. The wireless…
-
Allow Device Nicknames
Surely this is a very basic want/need? When registering my Tado X device, I’m even prompted to add a custom name for the device, only then for that to be completely ignored by the app, which goes ahead and calls in by generic name. Am I missing something?
-
Merged: Include a full calendar plan
This discussion has been merged.
-
The Tado Professional App must be updated swiftly to inform both V3 and X compatibility
That app is well out of date. We are facing a lot of enquiries about boilers and thermostats which arent identified in the app. The app needs urgent attention to declare properly the configuration settings to be considered: with both the V series and the X series given that their behaviour is not identical their…
-
Suggestions left unanswered.
Hi, Many of us have been asking for it for a long time. I am the new user of TADO V3+ and I am actually satisfied with it. However, after reading many suggestions of other users, Tado does not take it seriously. A lot of comments on the appearance and functionality of the main screen. Windows 8 appearance is ok but why is…
-
Ability to schedule "one time" events
Currently you can define a schedule but sometimes I have the need to just schedule a one off session. For example, Friday I will be home earlier than usual so I want to have the temperature be 20 degrees at 13:00 with the end-time being the "next" change. Its nice if this is possible because Tado will then pre-heat…
-
Select how long boost hot water for Tado X
I've switched from the V3+ to Tado X due to connection issues with the bridge. With V3+ in the app I could select how long to boost my hot water for with the pencil, this was a vital feature for me. With tado X I can click boost but it is only set for 60 minutes and can't be edited. I see from tado's website this is a…
-
Temp. Return sensor
Having a return temp. Sensor clamped on the radiator will allow more efficient control of the thermostat as it often over shoots on set point. Monitoring the return temp. Will make a huge difference
-
Worcester Bosch EMS2
It appears Tado is able to work with older Worcester Bosch Boilers with HT-EMS. Possibly some others Bosch ones with EMS+ ? It will also work on Relay (R01), On/Off Mode, but this will NOT modulate the boiler. All new boiler installations in the uk have to confirm to EnergyPlus Regulations. This means having some of…
-
Creat a new group for Tado-X users
Mods, can you create a new group for Tado-X usrs. It makes browsing through posts much easier, as V2/3 and X are not compatible with each other, and they do not share the same problems and solutions.
-
Bespoke Nom Circular Geofence
Allow a non circular Geofence to be plotted. We have a park near our house that would be good to have outside the geo fence, especially when the wife and kids spend a few hours there. If I reduce the current Geofence radius to exclude the park the Tado App says it's too small.
-
Boiler Immergas compatibility with digital bus
I just bought an immergas victrix extra 32 boiler and found that it is not compatible with the digital bus and I had to connect it to the on/off relay. can you make it compatible please? Thank you