-
Design of an upgrade to whole house - smart heating and hot water system
We are in the process of upgrading our home insulation (9” solid brick walls) and adding smart TRVs to the radiators and control of the hot water thermostat. I need detailed guidance on how to adapt the existing system to your system The current set-up is as follows: Upstairs - 10 radiators with a landing mounted…
-
Official Announcement: Flow Temperature Optimization now available for V3+ and tado° X users
Hello community, We are pleased to announce the release of a new Flow Temperature Optimization feature for tado° customers with V3+ and X devices directly connected to a boiler or heat source. Flow Temperature Optimization at a glance With Flow Temperature Optimization, you can avoid overheating your central boiler or…
-
Help with 3 channel thermostat
Hi, I’ve recently purchased a tado wireless v3 starter set. I have a Riello boiler and separate hot water controls with a wired thermostat. I was sure this would work. I’ve now realised that I have a 3 channel thermostat EPH R37 HW which the set up app says is not compatible with tado. I’ve looked online and it seems…
-
Tado X support for hot water?
I currently have a Nest controlling the radiators and hot water, and a Drayton programmer controlling 3 zones of underfloor heating. Both demand from the gas boiler independently. I think I’ve worked out that the V3+ supports this configuration with a wireless receiver and 3 wired thermostats. But am I right in thinking…
-
Upgrade to X and lifetime auto assist
Hi! I am wondering whether upon upgrade to X tado will honour the lifetime Auto Assist subscription that was available with some of the previous editions of the kits. I understand that V2/V3/V3+ can't co-exist in one account with X, but I am wondering if it upon upgrade and removal of the old bridge, the subscription would…
-
Tado X and home assistants (adding important elements)
I added official integration, but for tado x I see only outsite temp, localization, solar energy (prediction) and tado mode nothing else. I need hetting status, actual temp., sett. temp., humidity , opened window status, etc. For all added thermostats. For version V3+ all info is available in home assistant (google home…
-
Connecting a Smart Wireless Temperature Sensor X to the bridge
Dear community, I joined newly the Tado community. At home, I have installed so far 4 Smart Radiator Thermostat X and one Bridge X. My first impression were OK. I wanted to add Smart Wireless Temperature Sensor X to have a more accurate temperature measure. During the installation in the app, I receive a failure "Thread…
-
Tado X and Home Assistant
I purchased the new X thermostat and valve system. I am hoping for more Home Assistant integration, as is the case with the V3 system; it doesn't offer much at the moment.
-
Tado x smart thermostat and Junkers boiler
Hi everyone, I have a Junkers boiler and a Fw120 thermostat that I want to change for a tado x smart wired thermostat that I just bought. My Fw120 thermostat has b1 and b4 wires connected, also a b2 wire not connected. Do you know where those wires from the boiler should be plugged on the tado x smart thermostat? I tried…
-
time to send the order from the app
Hi! I have a tado X thermostat and when I use the app to turn on the boiler, it takes about 1 minute to send the signal. It's normal? It takes a minute to turn off too
-
Daikin Heat Pump Compatibility
I am looking for a smart home heating solution and contacted support to assess compatibility for Tado X which states it accommodates under floor systems. Support informed me that Tado X is not compatible with Daikin Altherma R F - EHVH-CB and Daikin ERLQ006CAV3. I would suggest adding compatibility as this is a widely…
-
Tado X Smart Radiator Thermostat - poor battery life
It has been less than 2month since I installed Tado X system and the batteries in the TRVs started failing already. The system has hardly been used (apart from testing) so battery depletion seems really premature.
-
Tado X add to current Home with V3 versions
If you already have several Tado V3 TVRs if you purchase an additional New TVR X & the new X Bridge do they get added to the same home as the current Tado v3s or does the app create a 2nd Home? I would like all my Tado devices to show upmon the same Home screen?
-
Tado X suggestions
(I originally messaged this direct to Tado but they asked me to repost it here.) I have read that currently your Tado X heat pump controller supports only some makes of ASHP as of yet but based on customer requests you will add more. I am therefore contacting you to suggest both Samsung Mono HT Quiet, and Daikin Altherma 3…