-
Make a window sensor that turn the heating off (the open window detection doesn't work so well)
Make a little window sensor as an option that could be installed at a window and connected with one or more Tado thermostats, so that one or more thermostats totally close the heat, when the window is open. The present open window detection closes if it feels colder air, but it works very badly because it often turns heat…
-
Decrease burner power before lowering target flow temperature
Hi, I have a bosch condens 2500 boiler, connected with nefit opentherm-ems converter. Using this setup with tado x wireless receiver (+trvs, wireless thermostats), via opentherm control. As far as I see, this setup works well, changing the target flow temeprature and setting the burner power to minimum value happens, so…
-
Boiler Overun
When all heating demand is stopped our boiler goes into overrun and dissipates it heat into the garage (where it is not required). It would be good if when the heating is not called for boiler heat demand signal is stopped but the radiator valves would stay open for a adjustable time to use the stored boiler heat in…
-
Battery status Matter
Hello, when Tado X radiator thermostats are connected to HomeAssistant using Matter Addon they dont show battery status because its not sending any. The radiator thermostats are connected through other brand Thread Border router.
-
Wireless Receiver status
I'd like to see some status on Wireless Receiver, which thermostat is activating, a diagram would be also good, I'd like to see what is the running time of my heater in a day, could be also an indication of which room/device started/use it. Also, in Home Assistant the status of the thermostat is "heat", never goes "off",…
-
Guest mode
There could be an option for guest mode, which would use a different schedule.
-
Better explanation with regards to termination of the old thermostat wiring.
I have recently installed the V3+ system and everything went well with regards the installation. I could see all the devices on the app and all the test procedures passed on the Wireless Receiver. However, the heating and hot water would not work. I was convinced I had done everything correctly and was struggling to…
-
Exclude rooms from the energy report
Is it possible to exclude the heating of certain rooms from the energy report? Because I have a room in my home where the heating is centralised (but it still has a Tado on the radiator) and it doesn't impact on my bill… And as it stands it impact my energy report because it is constantly on. Thanks in advance
-
Change your shipping delivery service provider
Not just me, but many other customers from ROMANIA are dissapointed with the service provided by UPS. Packages from Tado and other european businesses are not delivered and the reasons invoked by UPS are FALSE: incomplete contact information, the receiver was not available for delivery. UPS doesn't contact the receiver at…
-
Local Mode option for Tado X
Reading the manuals it would seem that if a wireless temperature sensor goes offline, the controller will continue to heat as per the schedule. However, with the server issues the last couple of days I had the following; One Wireless receiver X controls one zone and hot water and was running a schedule. The wireless…
-
Tado Support
This has to be better. It’s the only real serious downside for me in the U.K. No phone number to call in emergency. No instant answer via online chat. It’s not good enough.
-
From 5 to 6 digits meter readings in app
For more than a year I have not been able to upload my meter readings, as my meter is now above 100000 KWh. The app does not allow more than 5 digits, so my EnergyIQ is not very useful anymore. I do not understand that I may be the only person in the world with this issue.
-
Merged: Ability to manage more than 1 Home
This discussion has been merged.
-
Allow Device Nicknames
Surely this is a very basic want/need? When registering my Tado X device, I’m even prompted to add a custom name for the device, only then for that to be completely ignored by the app, which goes ahead and calls in by generic name. Am I missing something?
-
Hot water control like in V3 - other device control i.e. Apple Home, Google Home or Home Assistant
I have found it impossible to see any control of the hot water in any of the Matter/Thread control systems. It is impossible to add the wireless controller X to any of Apple Home, Google Home or Home Assistant. The only place that hot water can be controlled is through the app, and then only with the facility to set a…
-
Please implement Dark Mode for app.tado.com
Please add dark mode for the web app. It would enable me to control my home after dark without sunglasses on. This should be low hanging fruit. It's basically just adding some css.
-
Better adapt to slowness of underfloorheating
I have a setup with underfloorheating downstairs, radiators on first and second floor. the smart thermostate steers the floorheating valve by it's relay and a heatpump wirelessly trough an expansion kit. folowing the opentherm protocol. set temp on ground floor is set to a fixed temp 24/7 the heatpump should optimally run…
-
Prompt for Zone Controller
When installing multiple thermostats and radiator valves, there should be a prompt to choose which themostat is the corresponding zone contoller for each radiator valve. After setting up a wired themostat to the main boiler and a wired thermostat for underfloor heating, my radiator valves were randomly/intermittently…
-
Calendar viewer
Hi all in my previous smart thermostat I was a calendar viewer that was very useful, basically is a calendar with a month viewer where for each days where the thermostat was on, appear a red dot under the day, this is very useful to have a fast view of the days where the thermostat operate, and by clicking on the…
-
Allow combining Smart AC Control and Smart Radiators in one room
Currently, Tado App doesn’t allow combining Smart AC Control and Smart Radiator in the same room. Please enable this feature.
-
Tado x Thermostat - Set the MAX temp
Hi, I need (so fast as possible) the ability to lock (via software) the thermostat X or to set the max temp so that people cannot set the temperature above the set threshold. Urgent!!
-
Zone controller by definition off
In the current softwareversion all installed thermostats get the same zone controller after installing a wall thermostat. This should not happen by default. Can't this be changed by making this a configuration part of the initial installation when a wall thermostat is added to the system, where the user gets the option to…
-
Tado urgently needs the certificate for intelligent "hydronic balancing" (Germany)!
In Germany, switching from fossil fuel heating systems to environmentally friendly heating systems is massively subsidized by the government. One criterion for receiving this subsidy (e.g. 55% of the investment sum!!) is the requirement that the heating system in a house is optimized by means of so-called “hydraulic…
-
Merged: Include a full calendar plan
This discussion has been merged.
-
Moved: Geolocatie per kamer per gsm toestel. Nuttig voor thuiswerkers of oudere kinderen in het hui…
This discussion has been moved.
-
Tado Wifi enabled Hot Water Cylinder Temperature Thermostat Display & Controller
As far as I can understand, if you do not have a smart (oil or gas) boiler or a boiler that can separately control and heat only your hot water you are limited to the control and heating of your hot water cylinder by timer schedules only. However a timer schedule cannot detect if you already have enough supply or hot…
-
The Tado Professional App must be updated swiftly to inform both V3 and X compatibility
That app is well out of date. We are facing a lot of enquiries about boilers and thermostats which arent identified in the app. The app needs urgent attention to declare properly the configuration settings to be considered: with both the V series and the X series given that their behaviour is not identical their…
-
Suggestions left unanswered.
Hi, Many of us have been asking for it for a long time. I am the new user of TADO V3+ and I am actually satisfied with it. However, after reading many suggestions of other users, Tado does not take it seriously. A lot of comments on the appearance and functionality of the main screen. Windows 8 appearance is ok but why is…
-
Use a button instead of a slider
When enabling heating you need to fiddle with the slider to set the heating to a specific temperature but pretty much always I set the temperature to fixed value for a given room. It would be more convenient to just have a big button that would enable/disable heating and use the default target temperature (global… or even…
-
Ability to schedule "one time" events
Currently you can define a schedule but sometimes I have the need to just schedule a one off session. For example, Friday I will be home earlier than usual so I want to have the temperature be 20 degrees at 13:00 with the end-time being the "next" change. Its nice if this is possible because Tado will then pre-heat…