-
Black edition TRVs
It’d be super if there was a black edition TRV to match the new black edition thermostats - would look nicer on black radiators than the existing white ones IMO
-
Global Device Error History
There's various system errors that are actionable and useful for the user to review for troubleshooting, if only they could review the relevant past historical info in one place focused solely on problems. An error log. lost signal periods for TRVs, sensors, receivers disconnected internet periods for the internet bridge…
-
Feature request: consider central heating schedules
Hi there, I live in an apartment block with a central heating boiler. It does not run 24/7. There is a schedule that can vary every year or on special circumstances. I believe this is a very common situation in Spain, maybe not so much in other countries. So I cannot have the heating on at any time I choose, but only…
-
Make Opentherm boiler specific tweaks possible
Hi! I'm having an issue with opentherm using my boiler Enbra CD34H. After some troubleshooting I found out that issue is caused by Opentherm message ID 14 (Maximum relative modulation) being send too often by Tado (every 6s). Unfortunately support is unable to change this to 2mins intervals (which would fix the issue) for…
-
Zone controller assigning in API or create fireplace mode in TADO app.
So my problem is i can not control the zone controller from the tado API. I use Home assistant and would like to have the abbility to create a "Fireplace On" switch (in Home assistant or in the TADO app) that will toggle the zone controller for selected rooms. I have TRV's on all my radiators (except 2 bypass radiators).…
-
A Pause Button… with Adjustable Duration
I would like to suggest a Pause button… Similar to the Boost button but with the opposite effect. Or add a time restriction to the Off button. With the weather so variable there are times when the heating just does not need to come on if one of the rooms drops 0.2 degrees below the target temperature. With temperature…
-
Show the water temp that goes into a radiator or warn if too low
So, I had an issue with our central heating. Two-story apartment, the lower floor was fine, the upper floor not so much. Out of three radiators upstairs, one was kinda happening, the rest cold. I noticed it was a bit chilly. I played around with the two cold ones, removed the thermostat, and eventually called the landlord…
-
Set temperature for selected rooms shortcut
It would be useful if I can select the rooms fast where I would like to set a temperature for the next hour other than doing it individually. Thank you,
-
Active / Inactive rooms fast switch
I wold like to include a fast button for each room within the main view to mark that room as 'active' or 'inactive'. That way you can switch on/off the room you are currently using with a click. This would be nice.
-
Time block call for heat option
In the room time blocks, provide the ability to choose at different times whether thermostat calls for heat, or operates in passive mode
-
Smart AC Control V3+ / Setup Quiet Mode
Dear Support, It would be a great plus for the product tado smart ac control v3+ to support quiet mode. The controller already supports fan control and adding this feature will provide the benefit of completely giving away the hard manual controller of an older air condition. Maybe a generic mode could be added for the…
-
Allow additional schedules in addition to Home and Away
It would be great if it was possible to have additional schedules in Tado. I’d like if you were able to add additional schedules, such as “day shift” and “night shift” or “staycation”, so you can easily change schedules to meet your requirements. For example it I found i needed to change my normal schedule to account for…
-
modo frio para el termostato
Actualmente tengo un sistema de suelo radiante/refrigerante y necesitaría que los termostatos tuvieran una función de frío para poder usarlo tanto en invierno como en verano. Esto ya se lleva pidiendo durante años en el foro Tanto en ingles:…
-
Smart Radiator summer / maintenance / bleeding mode (leaving the radiator open)
When summer comes, the valves should stay in open position. With the currently available modes, specially referring to "OFF", the valves stay closed. This is dangerous for the valves themselves, risk to get stucked, and for the pumps of the boilers which run periodically to prevent pump lock due to long inactivity.
-
Group rooms
Can you add a feature to group rooms (i.e. ground floor / first floor etc) to a cluster to be able to boost / switch off with one click.
-
Holiday Schedule
Would it be possible to add in a calendar feature to pre-programme upcoming Holidays? E.g. enter a time and date for the holiday to start and for it to end? This would remove the need to remember to switch all heating and hot water to 'Off' as you leave, plus allow for pre-planning and set the holiday parameters (e.g.…
-
Bridge range extender
Nearly all my issues with tado revolve around lack of connection between the radiator thermostats and the bridge. Surely either a more powerful Bridge or a bridge extender could be developed
-
Change the hysteresis / PID settings
Hi Tado. The current desire of the smart thermometer algorithm to track the set temperature is killing my hardware. It is turning it on/off so often that things are breaking (like TCVs). How about I can select the min and max settings that trigger a state change? Or if it is a PID system, I should be able to change the…
-
Lowering frost protection or turn it off per device
I have a conservatory attached to the property and the temperature can go down as low as 3 or 4°. A useful feature to be able disable frost protection for this area or choose a lower level for frost protection, such as zero.
-
Some Suggestions
Tadoº Ecosystem Ability to use AC thermostat as a sensor to give temperature readings to radiator valves or the radiator thermostats (this is a big turn down). On the App (iOS) System: Ability to add shortcuts to iOS system, allowing to activate Boost Heating, Resume Schedule, Turn Off All, more easily. Geofencing: ability…
-
Timed override for geofencing
Would be good to have a way to override geofencing (to home or away, from auto) for a set period of time - like the timed manual override for TRVs. I manually override geofencing to ‘Home’ so that heating stays on for babysitters when I leave the house. But then I have to remember to turn back to “Auto” when I get home.…
-
Maximum Temperature Limit
Hi there, with the increasing cost of fuel , I was thinking that a maximum temperature limit may be of some use that could be set by the account holder in order to prevent "temperature tampering" by anyone not authorised. This could possibly be built into the app, and hopefully could save money. Any thoughts !
-
Visitors pre-set
It's probably been suggested before but I'd love a preset for certain rooms so you can quickly switch between occupied and unoccupied. For example we have 2 X guest bedrooms. When visitors come it would be really helpful to have a preset to quickly switch the heating schedule on just for their rooms. When unoccupied we…
-
show humidity on room tile
Why do I have to go into a room to see the humidity? There’s enough space on each room tile to add the humidity figure.
-
Display Humidity level on wired and wireless sensor display
It would be important to allow the display of humidity levels on the wired and wireless sensors (square devices) when pressing the round button. This feature could be configured in the app. The humidity level would be displayed just after the temperature. You can also extend this display to smart radiator valves.
-
Support newer version of Worcester HT-BUS
I just upgraded from a worcester bosch greenstar cdi to a worcester bosch greenstar 8000 life. On my old boiler I could connect to the digital low voltage interface bus however the new boiler the ht-bus is not supported and I couldn't simply change over I had to rewire to the old relay style. The bus interface is better…
-
Plieger
Goedemiddag, Wil toch even reageren op onderstaande mail van jullie. Misschien dat jullie er iets mee kunnen?! Ik heb een Herz adapter M30 inwendig naar M28 uitwendig gekocht waar een messing sukje bij zat wat over de pen van de kraan past. Ik heb enkel het messing stukje op de en gezet en….. tadaaa, de Tado knop werkt.…
-
Heating Manual Adjustment Notification
We have multiple people in the house and it would be handy to receive a notification when the heating is manually adjusted from the schedule.
-
Battery Monitor Improvements
As a suggestion, there needs to be better battery level monitoring\reporting between the Tado application and devices. I have noticed in recent weeks that devices are reporting battery levels as "Good" but then are malfunctioning due to suspected low battery life, which is then confirmed when you re-insert the batteries…
-
Alert
It would be good if there was a log file so that you could find out which window alerted "open window"