-
Tado TRV doesn't open valve enough for heat
Hi, I just installed tado on my 4 radiators. 3 of them are working just fine, but one of them, I don't know why, is not heating enough. I already tried to reseat the device and recalibrate, tried to move the valve pin to see if it was stuck (it was not), and leaving the valve without the TRV makes the radiator hot as it…
-
App issue
Why does the App keep signing out by itself?
-
Ecotec 824 and Starter Kit V4+ Wireless Smart Thermostat
Hi Ive just purchased a tado Smart wireless kit with 8 thermostats, I have followed instructions on the app and connected the bridge and wireless temp sensor and now I am stuck on adding the wireless receiver to the boiler. I see some conflicting guides on the tado app instructions. One of them shows that I wire the grey…
-
Installation wiring help
Hi there Tado just sent me really generic instructions. I've got the wired thermostat which is going into a combi boiler. I'm replacing a Sunvik SL The wires are N L and 4. On the tado instructions that is p1 (N) and p2 (l) and there's no 4 sticker. But then wiring into tado it has No nc com then 3 blanks and the…
-
Daily summary
We’re trying to get the best balance of temperature and schedule to keep the house reasonably warm-ish as economically as possibly and I’m doing meter reads daily to get the daily gas cost. Would be really good to get a daily breakdown of the number of minutes per day each room sensor calls for heat. I can’t see an easy…
-
API & Opentherm
Hi I'm about to get a new boiler (Atag IC economiser) which has opentherm capability. I'm v interested in the Tado v3+ controller, as it's the only one which allows for a 14 year boiler warranty AND has an accessible API. I'm aware that the UK controller doesn't have Opentherm - I'd need to buy either an extension kit or…
-
Tado switched heating on without instruction
I've just installed a wireless tado kit (no TRV's yet to keep things simple) and have set-up a Smart Schedule. However, this afternoon the heating switched itself on. In my schedule the target temp is 15 degrees however on the home screen the target temp is showing as 19 degrees. Can anyone help explain why they are out of…
-
V3+ radiator thermostats - temperature ring too stiff to turn.
I've recently installed 7 Tado smart radiator thermostats V3+ in my home. They are all working ok and I can control them easily with the app. My problem is that the manual temperature control ring is either very stiff or won't move on 5 of the 7. The other 2 work as expected. When I attempt to reduce the temperature by…
-
Why is Tado overshooting the temperature setpoint?
Hello, I have a Saunier-Duval ThemaPlus Condens (Gas condensation modulating boiler). Its max flow temperature is set to 60 C. Tado has been installed for more than a year. I don't understand the temperature in some rooms (with TRVs) overshoots the setpoint by a lot! The graph shows that a 17:30, the boiler starts heating…
-
How best to integrate tado with a Viessmann Vitodens 200-W?
The Vitodens 200-W has a KMbus+ which doesn't support Tado. Would it still be possible to let the boiler control the flow temperature modulation and weather compensation, and then separately Tado can control the TRVs timing and temperature just through the wireless hub? Or is something similar possible?
-
Status of radiators when cannot reach bridge
I have 10 smart thermostats on radiators. Two of them intermittently disconnect from the bridge (which is connected fine to the internet as the other 8 smart thermostats show all OK with connection). I am currently away and the Away setting says keep every room at 10 degs C. This works well and whenever a room goes below…
-
Nest thermostat and smart Tado radiators
I just bought the tado smart radiator thermostat (4 + bridge) to have more control over the temperature in our bedrooms. I understand that the radiators only heat when the Nest thermostat (connected to the boiler) is programmed to heat. I’m fine with that! The problem I’m having is that the smart radiators are not stopping…
-
TRV says temp is lower than roomstat - roomstat is measuring device for room
can anyone explain this? smart TRV on the rad, smart thermostat on the wall (the roomstat is the measuring device for the room) room temp set to 21, roomstat thinks the temp is 21.5, TRV thinks it's 20 (and suggests it's calling for heat). which is one right and why is the TRV saying it's calling for heat when it's not the…
-
Boiler doesn't get hotter than 57 degrees?
When my boiler (Intergas Eco RF 30) is heating my radiators it shows code 5 and then a temperature It never goes higher than 57 degrees, even if the house is freezing and I set the thermostats to 25 degrees I've set Max Flow temp to 70 via the installers app, and tried setting CH temp on the boiler to 70 too, but it…
-
Is the wireless room stat much better?
Having had a nightmare with one radiator SRT which was basically useless and over reading then under reading and keeping the room cold when it could call for heat I switched to independent. It was better but it had a -2.5C offset and the room temp had to be set between 22-23c to get 20c first thing and it would slowly…
-
Frost Protection Not Heating Radiators
Maybe I'm confused but I've noticed my heating igniting randomly during the night. After checking the app, it thinks my rooms are less than 5 degrees so I'm assuming the Frost protection is kicking in. Is there any way for me to know this is the reason? And secondly, why aren't my radiators getting warm if this is the…
-
Tado not working.
Hi I have recently bought a tado thermostat and am really not impressed with it at all. It seems to have a mind of its own, comes on randomly and half the time i actually want it to come on it does not come on at all. I wish I could take it back tbh. All i want to do ia set the times i want it to go on and off and also be…
-
Configuration Help
Hello, i have recently fitted the wireless starter kit to my system boiler set up (Y plan). All wired up correctly and heating works like a dream. My issue is that my hot water will not work. I cannot change the configuration on the wireless reciever to Y plan (green), every time i set it to green it resets it self to…
-
Is the wired starter kit all I need?
Hi, I've got a Honeywell ST9400C controller that has a physical wire connection to a thermostate in my hall and a physical wire connection to my hot water cylinder. The cylinder has a thermostate on it and the boiler is oil. The ST9400C has a House Heating side and a Hot Water Heating side ie the hot water and heating work…
-
Replacing old Danfoss equipment
I have a Danfoss RX1 with wireless thermostat. These are linked to a Danfoss FP715Si controller. Will it be possible to replace the RX1, thermostat and FP715Si with a Tado V3+ starter kit? Installation instructions allow me to choose RX1 or FP715Si but not both.
-
Boiler won’t switch off
My heating turns on via the app fine fires up boiler no Issues heats up rads. When I turn off via app it shows switched off however boiler still on. Anyone experienced the same issues before? I have to switch off boiler then back on and it goes back to normal. Not healthy to keep switching off boiler but then heating will…
-
Help wiring Tado Hot water receiver
Hi, I'm trying to install Tado myself and I ran into something and would love some help. I live in a new build. There are 2 zones for heating and 1 for hot water tank. There are 2 thermostat (ground floor Honeywell home analogue and upstairs Honeywell Cm707. Lastly I have 1 programmer (Honeywell ST9400C) which is…
-
Using the tado° system
Hi, I live in a seven-year-old three-story townhouse. I have an Ideal gas boiler (logic Heat 12) with a separate hot water tank. A Honeywell ST9400C controller and a wired analogue Honeywell thermostat, (possibly a T6360B). All but the hall, and two landing radiators are fitted with thermostatic valves. The thermostat is…
-
Honeywell ST9100C Hot Water Controller and Honeywell CM907 Wired Thermostat
Hi there, Similar to annother queston but in this case I have a single wired thermostat for the home central heating control. Having read a bunch off information from various forums, would I be correct in thinking that the Tado syste I need to replace both my Hot Water Controller and Central Heating Thermostat is the…
-
Installation issues and Tado is ignoring messages
Hi I just bought a wireless thermostat and have issues installing the receiver as I cannot find the exact electrical "piece" in the instructions within the boiler. There is nothing exactly the same. Main Eco Elite 25 I have contacted tado chat three times and the only reply I get is we will get back to you by email - which…
-
Modulating Vaillant
Hello Just checking other peoples experiences with using the ebus system on the Vaillant boiler I have a Ecotec plus 824 using the Tado smart thermostat linked to the EU wireless receiver When getting up to temperature the system works perfectly but when it ticking over its firing for about 10 minutes at a reduced flow but…
-
need help with multi-zone heat control
Hi everyone, I have a question regarding multi-zone heating, The scenario is that I have a 3 story house. I have a single smart thermostat (wired) in the ground floor with an internet bridge. I cannot use `smart radiator thermostat` since it is all under the floor heating and there is no valve available. The ground floor…
-
System layout
I have followed these threads with great interest - and some confusion. I would be interested to hear other users' observations on the following: I have a 1963-built 3-bed bungalow which I have refurbished/extended to create a partially open-plan ground floor layout with one bedroom and study plus a small en-suite bedroom…
-
TRV and thermostat???
Hi, I have Tado TRVs and a wireless thermostat. I am probably being thick, but what use is the thermostat if all my radiators (except 1) have the smart TRV on them? Thx Gerry
-
Why is heating coming on in rooms set to 'off'?
Whenever I set the lounge radiator to say 19c (radiator smart thermostat), but want the main thermostat in the hallway and other rooms set to off (wireless smart thermostat) to save money, the system seems to heat all rooms regardless (rads are very hot to the touch). Surely the point of Tado is that you can heat only one…