-
Night mode/motor noise reduction
It is really great device for every room.... except bedroom. As you can see - last night staring with 0:00 until 08:00 thermostat adjusted more than 30 times using its motor - during just one night. Close to morning when it does this it wakes me up hours before alarm goes on. I came up with a possible solution after…
-
Wi-Fi Bridge
Hi, As I understood, the bridge is communicating over Radio frequency 868Mhz, not wifi. That is the true limitation off the bridge. Is there any possibility to have a bridge v4 that communicate over Wi-Fi ? So people just needs CPL (Communication Power Line) in their house to extend the setup ? Regards,
-
Merged: Second home problem
This discussion has been merged.
-
Black TRVs
Id also like to see black edition TRVs from Tado. I'd buy around 10 if they were available. The photo shows why.
-
Make Tado with multiple zones (more) fit for (hybrid) heatpumps
Dear Tado, Pleas make Tado with multiple zones (more) fit for (hybrid) heat pumps. This is now not yet in place for instance with the Dutch Quatt heat pump.
-
Oil Tank Gauge
I have an oil fired combi boiler and your smart heating controls, which work very well. It would be good if i could monitor the level of oil in my tank remotely using the Tado app Maybe some sort of wifi sender on the tank compatible with your hub and app would be good.
-
Incident Detection > Show boiler OpenTherm values / failure codes
For OpenTherm connections system should pass over the boiler properties and failures I am occasionally getting 2: Low water pressure errors presented on my boiler LCD (which also means no hot water or underfloor heating for me) and TADO app never shows there is failure with boiler or no heating / water Looking at OpenTherm…
-
Provide multi room support for external temperature sensor
Now you can just set the temperature reading to one room, it would be ideal to allow the sensor to be used for more rooms/valves. You can limit maybe the number of rooms so to avoid selling one temperature sensor for a whole house, but on the other hand you cannot think I should spend hundreds of Euros for just this…
-
Open valve mode when system is off
During periods in which the system is off (I e. Summer), provide a function/button like "fully open valves", which behaves like the rocket 🚀 function, except it can be set for a longer period of time (even months). This way the water circuit is left open and the valve is not stressed because it's fully opened.
-
Bypass offset settings when valve is closed
If valve is fully stopped, then bypass offset so to provide the most correct temperature
-
Radiator Thermostat Vertical design
If we get a Next Generation with Thread/MATTER? (Hopefully to help with range) Radiator thermostat radiator valves keep the same connection at the bottom of the TRV like the current design. Do most of us have the TRV vertical on their radiators like most in UK or positioned horizontal?
-
Heating configurations
Related in a way to being able to select multiple rooms - it would be handy to be able to create heating schedules based on different scenarios, for example; working from home, not working from home, one person away etc. Would be great to switch between them and have the schedule reflect the rooms I need heated and when…
-
Room temperature calibration
You can set a temperature offset but usually the offset is different depending on the actual room temp - so offset usually is accurate for high or low temperature but not the other (due to non-linear temperature profile of the room from a point not near the TRV). It would be great if I could take the TADO wall mounted…
-
Send start/stop request for pump floor heating
I know there is an (unsuported) API. Where you can check for temperature changes every 5 minutes. In my opinion, the long interval (5 minutes) makes the API useless. I am looking to control the pump of the floor heating. At the moment I do this with a termperatuur sensor on the heating-pipe (towards the floor heating).…
-
Away mode for individual users/rooms.
When I’m at home and my housemate is out their bedroom does not need to heated and vice versa for myself. Is it possible to use the geofencing feature to see which users are at home and heat rooms accordingly.
-
Fix the geofencing functions that I pay for
I paid Tado so that my heating would use geofencing, well it does not. When contacted Tado say there is an issue but have not provided a resolution. First it was my partners phone that would not be picked up, so we changed the phone as there was another app with another issue. Her phone now works, but I don't see why her…
-
Fix the formula that converts cubic metres to kWh
I give readings to Tado from my gas meter. The monthly cost however is vastly out. The cubic metres are the same as my bill, the tariff is the same but in Tado my bill will apparently be less. I have just switched between suppliers having moved into a new house and they both naturally have about the same calculation to…
-
Pouvoir programmer la réactivation du chauffage
Comme chez Netatmo lorsque j'indique quitter la maison en hiver, j'aimerai pourvoir indiquer une date et heure d'activation de réactivation. Ceci pour tout la maison mais aussi pour chaque pièce.
-
Widget
Hallo het zou fijn zijn als de Tado applicatie ook een Widget kan oproepen op het beginscherm, misschien leuk voor de volgende upgrade !! Succes Met vriendelijke groet Stephan J Vestallen
-
2FA / MFA - EU legal requirement
Hi, I've created a new post to again highlight the importance of this to Tado. Without 2 factor authentication/MFA, Tado will soon be in breach of EU law. In 2022, the EU Commission proposed the Cybersecurity Resilience Act (CRA) which introduces mandatory cyber controls to, amongst other things, IoT devices including Tado…
-
Ebus Max Flow Temperature setting (like the one just released for Opentherm).
Would it be possible to do the same for Ebus controlled boilers via the wired Tado, +- settings? My Vaillant can ramp up to 80C if it wants even if I set the max temp lower on the boiler. The ebus will ignore these settings and do what it feels is best. I might only want it to go to 66 or 70C max for example. It's just…
-
An IFTTT applet to reset Tado to OWNER'S smart schedule every 30 mins. For Landlords or parents!
I don't know how IFTTT applets are made, whether someone one there does it or someone at Tado has to Okay it but other smart controls have anti-tamper applets for this purpose. 30 mins would be enough to give someone a heating boost. Please see thread:…
-
A must change issue for Tado!
We have a holiday home for rent, and it is very irritating that tenants can change the programs on the smart thermostat. They must be able to change the actual temperature, but not the settings and programs on the thermostat. Also kids can make changes unintentionally It would be a great improvement that changing…
-
Icons for each room type
Can you give the ability to select a range of icons that can be applied for each room that we have. The Hot Water icon is a great example of a visual icon that is easy to see very quickly. We have 14 buttons for heating rooms in our house and it would be very helpful if there were icons for different rooms. For example,…
-
Better accessibility support in the mobile app
Hi there, Due to the lack of features in the web app (which is bizarre enough on it's own), I'm forced to use the mobile app on a tablet to access a dashboard on a device large enough to read and interact with as I age and my eyesight increasingly worsens. I'm cool with getting old (ok no I'm not, but there's no one to…
-
Add timer option to Geofencing option
Add a timer option to the Manual select Home / Away Geofencing options, so that you can override any devices that are reporting as home but are not at home for a specific time length or indefinitely and on the flip side ignore devices that are away. But after the timescale is up go back to manual mode ;)
-
indication that the heating boiler is running
on the app main screen showing rooms another box saying if boiler is active or not
-
Offer a cheaper radiator valve.
In rooms where a wireless temperature is used as the control device there is no need for the SRVs to be able to sense temperature. Why not offer a cheaper version which only opens and shuts the valve as demanded by the wireless sensor.
-
Control zone valve and boiler with receiver? (Underfloor and radiator zones)
Hello, This is a new system we are setting up as we have just done an extension with underfloor heating and fitted a new boiler. We have underfloor heating one large room(the extension) downstairs and then radiators in other rooms. We have 2 zone valves installed, one for the underfloor heating and one for all radiators.…
-
Energy IQ tariff information
Energy IQ is only useful if it is accurate, and it's accuracy is dependent on the information you supply it. Currently tado is asking for the price in £/Kwh when gas is costed at p/Kwh. The app does not allow the cost in £/Kwh to be given to 4 decimal places to allow for more accurate cost estimates.. It should be fairly…