-
Profiles (again)
How much work will there be to enable us to create differnt profiles in the app? I know its been asked before but users seem to have an answer by adjusting the existing home profiles. I DONT WANT TO DO THIS. I want to press a button when for example we have guests staying or if we have a snow day or i'm working from home…
-
Schedule a boost
I am often away from home. My underfloor heating has a 24 hour thermal lag from 6 degrees to 22 degrees. I regularly forget to preheat it. Can you please add a facility to diarise a temperature boost for one or more rooms?
-
Smart Global Off Time with Conditional Notifications
Overview: I’d like to propose a feature that allows users to set a "Global Off Time"—a hard cutoff time at which all heating devices in the system are turned off or reverted to a predefined safe state (e.g., frost protection). This feature would address the issue of unexpected heating events during the night, offering…
-
Notificación al móvil en caso de encendido/apagado de calefacción
Una sencilla forma de saber si se ha puesto en marcha la calefacción en nuestra casa (o en una estancia de ella) a través de una notificación al móvil (tira o globo) especialmente si nos encontramos fuera de nuestro hogar. Igualmente se podría notificar apagado de calefacción. Estas notificaciones podrían activarse o…
-
Provide method to specify type of heating system, i.e. radiators, underfloor, etc.
There is no facility to specify what type of heating system is installed. It appears Tado treats all systems as if the heating system is based on radiators. In case of a underfloor only system it is likely the floor is cold when the first call for heat after a break is generated. Currently the system would start to run for…
-
Set Humidex instead temperature
It can be useful to have the option to set the perceived temperature instead only the normal temperature. In the high humidity zones temperature is not significant. It would be nice to trigger the air conditioning with your wireless control to decrease humidity.
-
Smart wall plug for underfloor heating pump
You offer nearly everything except a way to turn a underfloor heating pump on or off. My living room thermostat is connected to the underfloor heating, and to control the pump I have to set up a complicated process through Homey and a Z-Wave smart wall plug. It would be great to have a Tado smart wall plug which can be…
-
temperature adjusted at the radiator valves
If the temperature is adjusted at the radiator valves, that new temperature remains set until someone adjusts it again or until someone chooses to go to the schedule at the next schedule change. I would like to be able to decide myself via the setting what the reaction should be when turning the radiator valves. In my…
-
Humidity visualization and routine with modality home, away
It would be useful to have an indication of the humidity directly on the room box to have an immediate idea of the environmental well-being. Also on the environmental well-being box to have a summary of the situation without clicking on it. It would be useful to have the possibility of programming the "home" or "away"…
-
Dedicated tile for boiler status on/off (same as hot water)
Im fairly new to Tado but one feature i've seen that is so blindly obvious i though i was doing something wrong. It would be great to have a tile on the app which shows if the wireless recevier is actively calling for heat. Similar to the "hot water on/off" tile. A boiler on/off tile. I know there are the ~~~ wavey lines…
-
Give users access to the advanced configuration parameters
As most of us here will be aware, Tado has several advanced controls and configuration options that support are able to use to configure your devices when you contact them (cycle periods, minimum on/off times etc). Sadly these advanced options are hidden from users and the only way to access them is through support which…
-
Add humidity in the tiles
The current tiles have enough room to add more information like humidity. Additionally you could a a toggle in the settings to toggle on/off certain displays.
-
Switch between rooms in graph nice
When in graph mode, one can change the date range with the ˅ symbol next to the date. It would be so much easier to switch between rooms if there was a ˅ next to the Room/Device name as well. Now I have to go back twice (first to the Room, then to the home screen) to select a new room and view the graph
-
Set minimum opening percentage on smart radiator valves
Despite fiddling with pump speeds and lockshields, I still get water rushing noise in some of my radiators when the smart valves are open only a small amount. Being able to increase the minimum opening percentage would prevent this.
-
Home planning quiz
I have just installed a heat pump and I know I will need a heatpump optimizer, but I don't know if I need a Programmer with Hot Water Control also. It would be useful to have a way to get the best possible solution for one's home based on a quick quiz to design the right system for one's home
-
Tado X wired with OT changes the temperature of domestic water
In my boiler, Tado X wired thermostat connected through OpenTherm changes domestic water temperature to 60 degrees even if it is not supposed to. When this happens the temperature cannot be adjusted anymore from the boiler: if one tries to change it from the boiler settings, it immediately goes back to 60, as if Tado X was…
-
Funzioni in app
1 ) Sarebbe utile integrare in app la possibilità di variare manualmente la temperatura di mandata dell'acqua. 2) Quando alla caldaia è collegata una sonda esterna utilizzare la temperatura letta da essa ( sicuramente più precisa ) per regolare la temperatura interna perchè i dati del meteo sono troppo generici e succede,…
-
Grouping rooms for boost/off
I have our house divided into rooms with timings setup that work majority of the time. But, it would be good to boost multiple rooms at once but not all rooms (eg downstairs). Would be great if you could have boost/off zones that consist of multiple rooms, without it being all rooms.
-
Enhancement to Energy EQ - add specified radiator output to rooms
To assist Energy EQ in estimating the amount of energy/cost per room, allow the addition of the total radiator BTU output per room. Even without knowing system flow temperature, as long as the total radiator BTU specs per room were added (all need to be at the same rated temp as not all use 70 degrees), combined with the…
-
Smart AC Control X
You should definitely make a Smart AC Control X. Tado X is awesome, but the finishing touch would be automatic dehumidification. Using the air conditioner to dehumidify in the winter is a lot more energy efficient than opening a window. I'd love to be able to set a target humidity level or range, and have you take care of…
-
Humidity on app home screen
it would be very useful to show not only the temperature, but also the humidity of each individual thermostat on the app home screen
-
Don't recalibrate smart radiator thermostats at night
I think I'm slowly getting used to the sound of the radiator valves turning on in the morning. But in the middle of last night I was woken up by the one in the bedroom doing a full on/off cycle - presumably a recalibration? Maybe following an update? I could hear other valves in the house doing a full cycle afterwards,…
-
Pre-heat and early start for Tado X
Hello, Just bought the tado x System and I am a bit disappointed that the pre-heat and early start feature are missing. Are there any plans to implement those two features? Please implement those two features🙏 Thanks, Florian
-
Note Option
I would find it really useful if there was a note field for each device. When changing batteries if I could record when I actually change batteries it would help understanding how long they last before replacement - could obviously also be used to record any other useful info.
-
Merged: Features Tado X Early Start - Profiles Scheduling
This discussion has been merged.
-
Change schedule change for all rooms simultaneously
I would like a simple method to change the schedule for ALL rooms by the same time simultaneously. i.e My heating profile is set to start at 6 am and to warm the house in stages by 8 am. For next week only I want to bring that forward 2 hours. Currently, it seems that I have to change the schedule for each room…
-
Bespoke Nom Circular Geofence
Allow a non circular Geofence to be plotted. We have a park near our house that would be good to have outside the geo fence, especially when the wife and kids spend a few hours there. If I reduce the current Geofence radius to exclude the park the Tado App says it's too small.
-
[suggestion] Change icon for room block
Hi! On the Room & Devices screen you have a list of blocks. Each block represents room and devices located in this room. It's clear when you see right arrow icon for the device. Once pressing you see device settings screen. But when I see the same arrow for the room - it's not clear what it does. Actually it opens a screen…
-
Suggestion: enable Homekit Away/ Home automation
Tado should allow homekit users to toggle the home / away status of tado, using homekit automations. Issues; - Expensive - Tado charges £29.99/y just to toggle auto geofencing (extortion). - Privacy issues - I have to always share my location data with tado. I don't want to do this. - No support for guest / multi house…
-
Tado X and home assistants (adding important elements)
I added official integration, but for tado x I see only outsite temp, localization, solar energy (prediction) and tado mode nothing else. I need hetting status, actual temp., sett. temp., humidity , opened window status, etc. For all added thermostats. For version V3+ all info is available in home assistant (google home…