-
Installation on to Alpha Boiler
I have an Alpha CD35C combi boiler with wireless 7 day thermostat. I have received my tado receiver kit and have a query over which terminal block i connect to at the back of the boiler 0 i have added photos , if anyone is able to help?
-
Alpha CB24X help
Hi, I am looking for a little help/guidance on how to wire up my boiler with the Tado as I am a little confused on how this works. I have an Alpha CB24X combi boiler, programmable controller and wired thermostat. I have found the wiring terminal and taken a photo attached but the wiring is confusing me, looking at the…
-
Rav adapter too loose
Hi! Have the Danfoss RAV sockets and have tried using the adapters from Tado, but no matter how much I tighten them, they are still a bit too loose. Any suggestions on how to fix this problem?
-
Geofencing not working
Since the last updates geofencing no longer working as it should. Tado says the problem comes from Apple and advises to always leave the app open. But apple says they haven't changed anything related to gps-locations, the advice to let the apps open only have to do with battery lifetime. Apple say apps should continue to…
-
Can Tado app users delete other users?
I'm wondering if I set up a 'Home' in the app, then invite others, can they then delete my account? I can see I can remove them. Or is there a concept of an account 'owner'?
-
Is this valve compatible with the Smart Radiator Thermostat?
Could someone tell me if the valve on the images is compatible with the radiator thermostat? Thanks in advance
-
Remote trouble
I am renting out my home on a popular website for short term stays (whilst living away for work) and using Tado to set the heating/hot water up for guests remotely. So far so good after a successful few months, and very useful as it is a 2hr drive away. But suddenly all devices have gone to ‘no remote access’. The weird…
-
Extension kit- Initially only wiring CH control OK?
Hallo all, I have a very simple timed on/off programmer which makes the call for heat. There is a separate physical switch for a 2 port valve which simply only determines whether the produced hot water goes to either the hot water cylinder alone (HW) or to both the radiators and the cylinder (winter). I.e. this switch is…
-
Installation Help, coming from a Drayton system
Hi all, I managed to DIY install Tado for CH control but HW is not working. Can you please help me with knowing if Tado is compatible and what the wiring should be? Btw, I absolutely love Tado so far, especially multi-zonal CH controls! I have a hot water tank in the roof extension with an older non-combi boiler (Worcester…
-
All of a sudden no heating. HELP
All has been working fine. Last night no heat to rads although app was demanding and light on Wireless receiver indicated CH on. Rads will heat if HW and CH are both on but HW will not heat!! As said if CH only selected message is getting to wireless receiver but not firing up the boiler.
-
To relay or not to relay
I mean this is quite basic but I'm not sure if I'm missed something. My Tado is all linked up and ready to install and I've hit a wall...my thermostat is ancient. I believe it's a Honeywell t7807a and is wired in with a live, neutral and earth (still in red, black and green/yellow!) And it's connected to a Worcester…
-
Help please folks noobie here
we currently have the starter kit wired thermostat. It wired in our dining room and all is working. However the room is now used for home office working with computers. This means that in the winter the rest of the house is cooler as the thermostat is giving a incorrect temperature of the house. What are my options to get…
-
A huge disappointment
I have literally bought and installed 12 valves V3+ wireless connection etc and found out all the smart features they have advertised are in a subscription, like geofencing and window detection. Really? I mean at least geofencing is a basic feature. Not only that I can get that with HomeKit anyway so what’s the point to…
-
Which Tado kits do I need?
Hi, thinking of getting a smart heating system and I’m tempted by the Amazon deal today. I have an Ideal Icos 35 boiler which provides heating and hot water, British Gas UP1L control panel, and a simple Honeywell rotary thermostat in the hall. Have TRVs on all radiators in the house. Living room has two radiators. I think…
-
Completely remove account
Hi Tado, I would like to completely remove my unused Tado accounts including email/login from your database (thus not only the Home). How do I do this? I can still see old email addresses which I can login with to Tado, they shouldn't be there. Thanks in advance.
-
TRV suddenly started reading 8 degrees too high
Trying to fix a problem with 'no remote connection', and after taking off the TRV and putting it back again, it's telling me the temperature in the room is now 28C, which it patently isn't. It feels like this is a valve that's going bad ...
-
Logic Combi ESP1 35 Boiler wiring for Wired Thermostat
Hi everyone! Good morning! I wired my tado thermostat to my wired heating system at home (Logic Combi ESP1 35 with Dual Heating Zones - 1 x front room thermostat and 1 x master’s bedroom) but it still isn’t letting me control the heating unfortunately. The current (not working) wiring / settings are: Old thermostat Wiring…
-
Thermostat crashes when mounted
Hi all. After a firmware upgrade to 54.20, one of my thermostats is no longer functioning. I have new batteries and had no previous issues with this one, and it starts up with its usual hello, but now, as soon as it mounts it just crashes - turns itself off no mounting process and nothing on the display when turning it.…
-
Using Tado to control UFH
Hi Guys I am about to embark on a pretty major building work project on my house. I am replacing my radiators on the whole ground floor with under floor heating. As far as I know what I would need to get this to work with Tado is wired temperature sensors in every room. The wire then gets routed to the manifold and…
-
Radiator valve connector/adaptor advice
Hi . I recently moved house where I had a full Tado set up with valves on all radiators. I left it all behind and want to do the same in my new home but the radiators have a different screw connection than my old ones. I have no idea what they are called but here is a photo. As you can see there is no actual screw…
-
Wireless v3 tado not compatible with ebus
Hello But disappointed with Tado. I quoted and fitted my first Tado control today. I wanted an ebus compatible control for the vailiant boiler I am fitting to give me load / weather compensation. I ordered the new wireless v3 or whatever and guess what there is no low voltage connections! I rang technical and they said…
-
Tuen on boiler when upstairs room temperature drops below threshold
Hi All, I have four tado trvs upstairs, one in each bedroom plus more in most rooms downstairs; including extension kit etc. I'm finding that in the evening some of the bedrooms can get quite cold as the night progresses. The main thermostat is downstairs in the hallway, generally I find that the hallway reaches…
-
smart thermostat always on
I've just unpacked my wired starter kit with TRVs and figured easy. But the Smart Controller seems always to be on. I wired it into my combi boiler but the CH was on whether I set the smart thermostat to 9deg or 25deg. Pulled it back off again and attached wires, and I find the Smart Thermostat always has COM connected to…
-
Faults
My tado keeps turning it self on even though it’s programmed to be off. Costing me a fortune and furthermore winding me up. Boiler plan engineer came to my property and said I don’t know anything about these tado but I will report it. He told me to video it and send it to Tado. :angry: can anyone help me please
-
Moved: afwezigheidsmodus
This discussion has been moved.
-
Underfloor heating + radiator setup
Hello! I have already several Tado valves installed in radiators, and I'm going to renovate my house and install underfloorheating in some areas. Planning on using SRVs for each 'zone' in the underfloorheating distributor as actuators and smart thermostats on each room (would be linking them so that the sensing is done by…
-
Navien Boiler Opentherm radiators lukewarm
I have recently installed a TADO control system in my house with a Navien NCB-40 Combi boiler and am struggling to get the boiler temperature to increase enough to get the room temperature warm enough. The radiators only ever get lukewarm. I have a wired thermostat connected via Opentherm and currently 6 Tado Smart…
-
How do Tado TRVs call for heat?
I have a Vaillant ecoTEC 627 boiler providing heat in an 'S Plan' to supply... Hot water with a motorised valve 4 underfloor heating zones (via a manifold and Heatmiser UH4 wiring centre) into which there are 4 wired thermostats, which I think I can replace with Tado wired thermostats (if I accept they don't support floor…
-
Replacing 2x Hive receiver system with Tado
Hi, In my previous house I replaced a nice easy Worcester Wave thermostat through the LV connections to a Tado V3 Smart Thermostat and Smart TRVs. The new house has an existing Hive system (excluding the use of the perfectly working hub as Hive refuse to allow its transfer of ownership - i'd need to buy a new one). Current…
-
Why is tado turning on the boiler when the room is 22.3 and the heating is set to 22
Now 22.4 and its still on burning gas