-
Daikin Heat Pump Compatibility
I am looking for a smart home heating solution and contacted support to assess compatibility for Tado X which states it accommodates under floor systems. Support informed me that Tado X is not compatible with Daikin Altherma R F - EHVH-CB and Daikin ERLQ006CAV3. I would suggest adding compatibility as this is a widely…
-
Tado X suggestions
(I originally messaged this direct to Tado but they asked me to repost it here.) I have read that currently your Tado X heat pump controller supports only some makes of ASHP as of yet but based on customer requests you will add more. I am therefore contacting you to suggest both Samsung Mono HT Quiet, and Daikin Altherma 3…
-
All room graphs in 1 place
Please offer either a consolidated graph for all rooms, or an easier way ('next, next, next...') to browse the room graphs. Currently it's tedious to exit each room page, enter the other, tap the graph icon; repeated x times.
-
Maximum opening percent and time on radiator thermostate
To ensure not to send hot water out of the radiator, it could be helpfull to could adjust the maximum opening percentage combined with maximum opening time, followed with a minimum closing time.
-
24 hour clock
The smart schedules are set using the. 24 hour clock. However, the next event for each room uses am/pm. I know I live in the UK with its outdated time but it would be useful for users to select a consistent 24 hour (or am/pm) format.
-
Boiler Immergas compatibility with digital bus
I just bought an immergas victrix extra 32 boiler and found that it is not compatible with the digital bus and I had to connect it to the on/off relay. can you make it compatible please? Thank you
-
Merged: Manage more than only one home-house in one/each account
This discussion has been merged.
-
Away/home status in Alexa
Hello, Since ifttt is OUT, it's important to have the tado status return on Alexa routine. We need to have this information: away, home. I think it's the same for google. Regard
-
Low/High humidity notifications
Would be great for Tado app to send a notification when a room has low or high Humidity, with the ability to set the level that the notification can be triggered.
-
Activate open window detection with external window sensors
I would like to be able to use my window/door sensors to activate ‘open window detected’. This would be a great improvement as it will speed up this process and will keep ‘open window detected’ on until I close window/door. I know this can be done indirectly by setting the heater to “off” with ifttt but this means that it…
-
Set a manual time limit on Manual Away Mode to go back to auto.
Set a manual time limit on Manual Away Mode to go back to auto similar to the manual timer mode on the TRVs/Thermostats.
-
Set the "Follow Me" functionality of my Midea Air Condition from the App
Issue The air condition Midea Silent Cool 26 Pro WF is equipped with a so-called "Follow Me" functionality. Activating the feature via the included remote control or on the device itself makes the AC use the remote control's temperature sensor to measure at the location of the RC. Tado is not respecting this setting and is…
-
Child lock for wireless temperature sensor
As per the title. The TRVs have a child lock function, but the wireless sensors cannot be child locked. As the wireless temp sensors effectively control the heating in the same way as the TRV, it doesn't make sense to not have child lock on them. Thanks
-
Mac M1 App
Bring the iOS Tado app to the Mac AppStore to use the features in which HomeKit doesn't support (Ie. Override Timer, energy reports, timer settings). When we had access to run these apps pre MacOS 14.2 or 14.3 tado was one of the best apps to use via MacOS for M1 devices which saved me from hunting down my iOS device. It…
-
Merged: After several years still no range extension?
This discussion has been merged.
-
Merged: support for multiple internet bridges
This discussion has been merged.
-
Notification
Can we have a notification when someone turns heating on please.
-
Additional physical sensors (presence, doors closed) for more targeted routines
Hi! It would be great to have couple of additional sensor types to allow more customised routines: - presence/motion sensor - door/window open sensor These sensors could be additional conditions to the routines, e.g.: - heat bathroom to 23 degrees only when the door is closed - heat Office to 21 degrees Monday-Friday 8-18…
-
Air Comfort
The ideal temperature in a room or zone is a matter of personal choice. The degree of humidity is a matter of climate. These vary and should be capable of choice and customisation not a level of humidity and temperature that tado decides should suit everybody regardless of preference and location. Solution. Allow for some…
-
2FA / MFA - EU legal requirement
Hi, I've created a new post to again highlight the importance of this to Tado. Without 2 factor authentication/MFA, Tado will soon be in breach of EU law. In 2022, the EU Commission proposed the Cybersecurity Resilience Act (CRA) which introduces mandatory cyber controls to, amongst other things, IoT devices including Tado…
-
Relay and Opentherm together
The Tado extension kit can control the boiler through a relay (simple on-off switch) or through the Opentherm bus. The bus allows for better temperature stability and higher efficiency as it tells the boiler to turn the heating up or down as necessary. If a heating system contains other elements, like a shut-off valve or…
-
Make Smart AC Control expose more AC settings to HomeKit?
Is there any reason why the only options in HomeKit are cooling, heating and off? In the Tado app I can see that it knows the commands for auto mode, dry mode, fan mode, fan speed, tilt, fixed etc. HomeKit supports these modes and settings, I don't think it would be that difficult to expose these modes and settings to…
-
Please implement the possibility of disabled the three LED lights of the internet bridge
Hi Everyone, the Tado internet bridge has three very bright LED lights. I would like to have the possibility to disable those LED lights please. A configuration as described below could be useful for all users: by default, after booting, the LED's are also on but in the app and/or the web portal you can choose to disable…
-
Make it easier to see which room is requesting heat by adding a symbol/colour to room Icon
I have a few rooms with smart TRVs and it always takes me a while to find which room is requesting heat. It would be easier if there is a little logo, or maybe a coloured border around the room icon if it is being heated.
-
Automating Home/Away process
Apologies if this has been raised before but I couldn’t find a reference. When setting the system to “Away” provide an option to revert to “Home” either by setting a future date (preferred option) or at least by giving the number of days user will be away. This would save user forgetting or if out of internet connection…
-
Cooling function for Heat Pumps with floor cooling
Please create a function where we can use Tado with a heat pump (equipped with a cooling function) connected to a floor heating system to cool the rooms (with Tado thermostat) to the specified temperature. Each room is equipped with Wireless Smart Thermostat or Wireless Temperature Sensor. The heat pump is connected to the…
-
Merged: Multiple homes
This discussion has been merged.
-
Merged: Manage multiple homes through one Tado app
This discussion has been merged.
-
Merged: Multiple homes
This discussion has been merged.
-
Merged: how to add a second (and 3th) home with Tado to my app
This discussion has been merged.