-
Worcester Bosch Greenstar 30si - No Power to Tado
Hi all, Have wired up my V3+ extension kit to the boiler following the instructions within the app for the Worcester Bosch Greenstar 30si, wiring into Ns Ls LR terminal block as per attached but on switching mains power back on, the extension kit doesn’t seem to be receiving any power at all. Boiler operating fine as usual…
-
Heating doesn’t start until I don’t open the app
Since a couple of months, I have noticed that although there s a routine in place the heating doesn’t start until I don’t open the app. I’m an iOS user and I haven’t changed anything in the app. Any suggestions?
-
Anyone got a fix for issue with Tado resuming schedule at midnight GMT (1AM BST)
I've been trying to save money by having Tado turn my TRVs off (or at least frost protection) which it does initially but resumes schedule on all rooms at midnight GMT (I first noticed it happening before daylight savings and now it happens at 1am). Have confirmed all rooms are set to only resume when manually instructed…
-
Adding Tado for wet underfloor
We currently have Tado set-up for our central heating (radiators) and hot water and working fine. This comprises a Tado wireless thermostat with Tado extension kit/programmer. We have one additional room that is wet underfloor, and trying to connect this room up to Tado as well. Our plumber replaced the Honeywell wireless…
-
im not sure
hi. all i have a wired starter kit. and have managed to set up the wifi bridge with the thermostat im stuck on this bit. when i removed my old thermostat it had 2 wires. i tested these with a meter and it was 240v. so mains? if i join these to wires together the boiler fires up. so it must need a relay in the tado so my…
-
Tado thermostat
My thermostat is getting worse, I have set programmes for when to turn on and off. It seems to do whatever it likes. Boiling through night freezing in mornings, I'm sick of it, would prefer a manual dial.
-
Balancing thermostats
Hi, my house is 3 storey with tado thermostat on 1st floor landing next to radiator with no TRV. I've added tado thermostat on ground floor where it is colder and of course that is usually calling for heat when 1st floor is already warm enough. Should I look to move "fixed" non TRV valve to ground floor at some point or…
-
Why no remote access for a room with two apparently connected radiator stats?
Both rad stats show up on the app as connected with good battery levels. The room they are in is connected to the same zone controller as all other rooms, which are fine.
-
Hot water stopped working
I installed 3 smart radiator thermostats. Now my hot water won’t come on, from either schedule or manual override. The radiators work fine. Any ideas?
-
Thermostat stopped working after turning off water stopcock
Hi, I've got a tado Wireless heating & hot water kit with 6 tado radiator valves. Everything was working perfectly until this weekend. On Friday I was doing some painting so removed a radiator from the wall in one room to paint behind it - this radiator had a standard non-Tado thermostatic valve. To remove it from the wall…
-
IQ readings
I’m confused. I’ve just started doing monthly reading and adding the data. Do I just add the data month by month or do I add 1st month onto the 2nd month and so on. I have not been been doing that just adding each month but I have just added my latest reading and it won’t let me And says. The current reading can't be less…
-
Worcester greenstar 34cdi wiring
Hi, I’ve purchased a kit and looked through a few guides and videos on how to wire to the boiler, I’ve seen a user (thread below) not wire into the Ns Ls ports on the boiler, but the instructions from Tado and Worcester advise to connect to these and not the bb. I’m not sure about the switch bridge where this goes on my…
-
Tado thermostat faulty
Brand new thermostat, faulty contacts, permanently output is on, not great. Sent message to tado, require replacement urgently, esp with having small baby in house.checked batteries all measure 1.56v everything synced ok, output on always, tapped the stat contacts opened but when called for heat output stayed on evem when…
-
Hot water constantly on?
We had Tado installed with our new boiler last week. All seems fine with the heating but the boiler was firing up at random times when nothing was calling for it to do so. We think we have realised that the hot water is constantly on so when we use the hot water, this then ignites the boiler. This is despite the app saying…
-
Mobile phone notification
Hi, is there a possibility of notification when the temperature changes manually on the thermostat itself? Not via Tado app but on the thermostat itself. Or if it can be set that when the temperature is changed manually so that the time is not infinite but the last set before returning to the schedule? Best regards
-
Heating motorised valve staying open while call for water but no call for heat
I've had a tado extension kit fitted onto an s-plan system. I have an issue where this sequence happens: call for hot water in the app hot water motorised valve opens call for heat in the app heating motorised valve opens cancel the call for heat in the app heating motorised valve will not close. cancle call for hot water…
-
Adding an Extension Kit/Wireless Receiver to existing system
After any thoughts on what I need to do here, as it hasn't worked as I was expecting (hoping!)... I have been stuck with a 3-channel boiler programmer that i could not replace as tado don't support 3-channels programmers. Therefore I have never been able to control the hot water via tado. Upstairs I have a smart thermostat…
-
The most important feature
I have 12 TRV's and two of them are disconnecting on a regular basis. Use of power line devices its not really a work around as is moving my whole internet connection setup. My question therefore, given the issue has been around since 2017 and other competitors have a solution, is this most important feature at the moment…
-
Not working
Only installed for 10 days will be removing as the cost for the system and it has a mind of its own it loses contact then leaves the heating on think the internet bridge is not fit for the job
-
Should batteries be considered as "Goodwill"
I have bought 12 Tado TRV's and in less than 6 months I have had to replace 6 batteries. When tested they were half flat. Having escalated to Tado, they advise that batteries are provided as "Goodwill". My counter to that is that tyres on a new car, are they considered as goodwill. Seems they are not prepared to shift on…
-
Can I read temperature and motorposition from tado thermostats
Hi' I've used Danfoss link for a while, but it is closed system and they really screwed their customers, so I'm looking for something else. Since I need to have the radiator system and my air to water heat pump play together, I would like to (I need) be able to read: 1) Temperatures in rooms (not sure if tado thermostats…
-
Feature request - Extra lock pin
I find it too easy to un-mount the thermostat from the radiator. If a person who has no experience with the thermostat wants to change the temperature and he/she grabs the thermostat and starts turning it, chances are that they will unintendedly dismount the thermostat. This happened to me yesterday. I occasionally rent…
-
Viessman,Tado wired Thermostat.
Good afternoon, I have got a Viesmann 100-W system boiler with a Heatrae Sadia Megaflo. I have the Vitotrol 100 UTDB-RF2 wireless thermostat/programmer. I have the wired Tado smart thermostat in and connected to internet but have been informed I need the extension kit also. I have also been told that this will not control…
-
Fahrenheit to Celsius
My smart A/C control v3 and app on my phone show only Fahrenheit. How to change to Celsius?
-
Ideal boiler not responding to call for heat/hot water
I've had an extension kit fitted today to an Ideal Logic Max Heat via OpenTherm. When I call for any heat/HW, the boiler does not respond, and only shows the standby '00' code, and no error message. All devices are paired, and firmware updated (81.1 on extension kit, 54.20 on thermostat). Thermostat is set up for OpenTherm…
-
Replacing BDR91
I have got a BAXI 130HE combi boiler, my bdr unit is wired to A and B (no earth, plug in boiler). Am I right in thinking these should go A->CH Com and B->CH NO?
-
Internet Bridge questions
I've been having problems with devices losing their connections to the internet. It has happened several times. On one occasion, the Wireless Receiver got stuck in the ON position in the middle of the night, and all the radiators got ridiculously hot. Most annoying. And I had to reboot everything to fix the problem. I have…
-
Adding hot water control
I bought a Smart Thermostat Starter Kit - v3 and several smart radiator thermostats back in 2018. It's worked well for the heating but we've never been able to control the hot water separately from the heating as we don't have a three way valve to enable that. However, we're now looking into getting a completely new tank…
-
Frost protection and air intake behind radiator
Hi! When I study the recorded temerature graph, I can see that the temperature lowers and rises in a wave pattern, which indicates that the smart radiator valve restricts the water everytime room temperature reaches the scheduled setting rather than finding the correct static restriction for the desired room temperature. I…
-
No heating only hot water
I installed our receiver, bridge and thermostat following all instructions. When I test the hot water it works fine, heating test fails and I cannot work out why. I got the product through my energy supplier and I’m wondering if I have been sent an incompatible one. We have a glow worm boiler, we have a hot water tank and…