Hi, Google Home Android app detects location and routines can be set for "home" and "away". Is there a way to propagate this home/away status from Google Home app to tado, i.e. not to use tado's geofe…
So I've fitted a wired thermostat downstairs which controls heating for downstairs and upstairs apart from master bedroom which has it's own add on thermostat! I've fitted a wireless receiver to contr…
I have a V3 system working fine at the moment with several wireless thermostats and 2 wireless temperature sensors in different zones. I want to change to the extension kit to take advantage of the op…
I have to admit im no boiler engineer but I have been following the threads and decided to purchase the tado starter kit v3+ wireless. Set up i thought would be quiet straight forward until it came to…
I'm thinking of buying tado again and I have asked this a while ago but didn't get an answer so I'll ask again. My house has 2 central heating zones run off a combi boiler. Downstairs is underfloor he…
Just installed wireless v3+ version to my Vaillant ecofit pure 830 combi boiler (UK based). The wireless receiver keeps making a clicking sound, and then all the lights go off for a few seconds and th…
I have both a wired and a wireless stat. The wireless looks after Underfloor Heating. How do i match the trvs to the wired stat. Do i install the wired stat first, then the trvs, then the wireless ?
Hi so I can do both are there any differences between them, the system I have is an ideal combination boiler with weather compensation already fitted ? Thanks
Set up TRV on the kitchen radiator. Room is sitting moderately cool (estimated 18C), tado app shows the room sitting at 26C... Cozy!!! Set up a Mercury thermometer right next to the valve. Confirmed t…
Installing the wired thermostat to get opentherm boiler control. Anyone know what the config menu ID should be for an Intergas Combi Compact HRE 36/30, or where I can find this?
When I come home my phone shows that my heating is set above the schedule and coming on. It's as if it goes into override or something (21deg rather than 19.5)? I've searched all settings etc but have…
Hi, My Heatmiser UH1 wiring centre and one of the 12v stats has some electrical faults and rather than replace the UH1 (discontinued, so quite expensive) and the stat I'm looking at Tado as I quite li…
I am often away from home & system is switched to away mode. I get visitors to the house who may stop over or use the office for work. I can't find a way of allowing them to switch on the heating or h…
Hi Community In my living room I have two radiators - a large an small. Then setting the temperature (grouped by room) the large radiator is medium warm but the small one tend to get very hot (capacit…
Good afternoon, I recently bought a wireless starter kit v3. During the installation on my Worcester Greenstar CDi (which currently uses a Comfort RF II receiver), I realized the kits sold in the UK d…
I have an ideal instinct2 24 combi boiler. I have the central heating AND hot water connected to the central heating side of the boiler. I have a unvented water tank. The heating is controlled by an E…
Hey there, Will try to explain my set up and hopefully the problem. I have a vaillant ecotec boiler and have been using the tado thermostat wirelessly and extension kit with ebus to the boiler. Works …
Hello all, I see there are lots of questions regarding compatibility with specific ASHPs, but none relate to my particular brand / model. Does anybody have any experience with this combination of pump…
Hi, Apologies if any of my questions have been answered, but I was unsure how to find them and what terms to use! I'm about to get the VR3+ starter kit installed, and am looking to get smart TRV's add…
I'm a little unsure what to do in my hallway, currently I have a wireless thermostat and one radiator with a manual rad valve. I am going to fit my tado wireless thermostat there, however I am unsure …
I have been waiting 193 hours for an answer to a simple question. I'm asking for my money back. Can anyone recommend a better manufacturer? Tado seem like a very difficult company to communicate with.
Had a new vailliant ecofit pure 415 installed and setting tado to ebus works boiler but not the hot water and heating valves from the extension kit. Resetting unit to relay control allows extension mo…
Last weekend I removed a room thermostat and knocked off the master fuse. Since then, I have to daily press the heat button on the tado receiver attached to my boiler. I've tried resetting the bridge …
Hello, I have a gas boiler (ferroli nem elite 60) and my tado tried to use heat request functionality. The boiler starts only on level 3 ( and its’s ok, because it’s just a relay). How can I turn off …
Hi there, I have installed five radiator thermostats and I have a problem with one of them. The thermostat is not updating and when I connected it to the radiator it calibrated just fine but it starte…