-
Minimum Temperature Settings
I am sure I've seen the answer on here to this, but after searching I cannot find any reference. Is it possible to set the lower / minimum temperature that Tado will try asking for from the boiler? I can see at present Tado on my system requests heat from between 32oC and 75oC. Due to the large size of my boiler 32oC is…
-
App setup for Village Hall
New trustees for Village Hall with Tado system controlling the boiler. All good, the system works, however the heat output is very low unless someone with the app on their phone is physically in the building. This is no good ! I want to be able to remotely set a block of time, and irrespective of whether I am in the…
-
Tado Smart AC Control V3+ in multi-rooms
Dear Community I actually control a air conditioner (Mutsubishi) unit located in my living room with a Tado Smart AC Control V3+ I've just installed 2 other units in the bedrooms. Do I need to buy 2 other Tado V3+ (1 per room) or a less costly solution exists? Thanks in advance for your tips Thomas
-
Help Planning my Installation.. Please!
Hi - Newbie here and I recently purchased a new house, larger SQft than I have had before. Its brick built 1999 5 bed detached. It runs a Potterton Suprima 80, with a Horstmann controller and a huge hot water tank. No cold water tank in loft. I believe this boiler needs at least 1 non-tv rad and a bypass? There are 19 rads…
-
Temperature homekit app and Tado app
Hello In Homekit I can see the temperature of the valves like this: 19,5C but in Tado app only like this 19. Is there any reason why we can not see the temperature in the Tado app with the decimals? BR Alex
-
Water gurgling when TADO valve is opening
My TADO radiator valve in bedroom create water gurgling whenever it is opening to gain heat. It is very annoyed during sleeping time when temperature is below 18 celcius (my TADO threshold is 18 celcius). Is it normal ? If not, how could I fix it ?
-
All on /off timer
All on /off timer would be better if it had a timer eg all on 8pm
-
How do I remove a Smart Thermostat from my system
Hi Could anyone tell me how do I remove a Smart Thermostat from my Tado system There doesn't seem to be an option available Thank you in advance
-
"No remote access" on some of the devices
I have successfully 18 devices on a single bridge. For no good reason, had of them went to "No remote access" and there is no way I can get them back online. The only thing I did differently compared to the last couple of months is using the button "Turn OFF all rooms" for the first time on the web-app. It looks like that…
-
All devices are showing as connected and boiler works fine, but no heating - SO COLD
So we have had an issue for a while now with our thermostat. The Thermostat shows as connected and paired with the internet bridge and these are connected to the Extension kit - lights all look as I would expect, so far so good. My boiler also works absolutely fine. However, when we turn the heating on, it only heats the…
-
Yes another Vaillant boiler wiring question :)
Hi All, sorry to add to the large list of posts about Vaillant boilers. So I have my tado (v3+) wired room thermostat connected direct to my Vaillant ecoTEC plus 837. All working fine on/off does what it needs to do but its just relay mode (I think thats what its called), was hoping to get some intelligence into the boiler…
-
no power to extension kit/programmer
Hi, I am replacing a Honeywell system and connecting up my extension box in place of the old programmer. I blew a fuse in the Honeywell sundial wiring centre during the installation but I have now replaced this. There seems to be no power going to the old programmer circuit which should supply the power to the extension…
-
High pitch whine?
Hi! I've recently just set up my Wired thermostat + extension kit replacing the boiler controller. It's mostly working fine (had a few connection issues with the extension kit which were resolved after restarting internet bridge and the extension) but the extension kit has always had this high pitch whine coming from it,…
-
Do I need Smart Thermostat if all rads have Smart Radiator Thermostats?
Have bought Extension Kit + 8 Smart Rad valves but not yet installed. I was planning to put the Smart Thermostat in the Entrance Hall / Landing, which has two rads with no TRVs, and then have Smart Rad Thermostats in all other rooms. Will this work OK/efficiently, such that in effect the Smart Thermostat is only…
-
Temperature offset
Do we need to do a temperature offset when adding the tado radiator value as it is placed so close to the radiator? I would have thought we don’t. But I’m asking as the option is there.
-
Tado V3+ AC issue with Mitsubishi AC
I have an issue with Tado V3+ to control a Mitsubishi AC, model MSZ-GB50VA with KM05E remote controller: some of the temperatures setup with Tado app are not sent to the AC, heat mode or cooling mode. I can, for example, setup 21ºC heat mode, but I can’t setup 22 or 23ºC. I can see that Tado is doing the change on its…
-
Best way to wire Extension kit for weather adaptation/modulation?
Hi, Got a new Worcester Bosch 8000 Life boiler and the electrician/heating engineer don't have tado experience. I have the extension kit and smart thermostat, smart TRV's etc. gravity fed hot water cylinder circuit with 2 port valves etc They are wiring the tado extension kit in the relay/switched live config in the…
-
Using installed SRV as a substitute for thermostat.
In process of expanding my Tado installation... and would like a thermostat in some rooms that is away from rads, even if they have an SRV. Why not set up an installed SRV on a shelf ...instead of more expensive smart thermostat ... won’t it do same job and half price ? many thanks in advance. james.
-
New to Tado
Follow up question please. how do you ensure the batteries last long time? How long should you expect... any advice to maximise the life ?? Many thanks in advance. james
-
Homekit not updating
Hello Do you know how to update the information in homekit related to the accessories? I removed one TRV from the tado app and it doesn’t disappear from the Home app (apple)
-
Rogue traders?
Hi all, anyone else found it impossible to get a satisfactory resolution from Tado customer services? We recently spent £800 on kit and TRVs and all works great except 1 trv that shows "no remote access" within hours of putting on any rad. Changed batteries etc to no avail. Tado initially responded but after level 2…
-
What Does This Infinity Symbol Mean?
Hi Everyone, I am new to Tado having just changed from Hive. I have a couple of questions someone may be able to help me with: This “infinity” symbol has just started to appear and having trawled through various posts and support docs, I can’t find any explanation as to what it means. Secondly, the installation was…
-
Another 3 channel programmer question (sorry)
I’m looking to add smart functionality to my existing 3 channel system, having read a lot of the other forums / questions i think I have a solution that will work for me but just want to confirm. I currently have an esi 3 channel programmer (CH zone 1, CH zone 2 and HW) with 2 wired thermostats. My plan is to keep the…
-
the Tado app allows you to see temperature history graphs. It would be good to have this on the web
the Tado app allows you to see temperature history graphs. It would be good to have this on the website
-
Tado turning heating on in the night - any ideas?
I have 7 rooms/radiators controlled by Tado with a wireless thermostat in my living room room and Tado TRVs providing the temperature input for another 6 rooms. Everything is on the same boiler and radiator loop. I'm in the UK if that makes a difference so it's a very conventional UK pumped hot water radiator system all on…
-
UHF Only - 3 zone - Opentherm setup
I'm setting up new heating system. I plan to use Viessmann Vitodens-100 as heat source. It is planned as UFH system only (no radiators). It' relatively small apartment (40 m2) and it will have 3 zones (Bathroom, open space Hall-Kitchen-Living Room, Bedroom) Since boiler needs to reach UFH specific temperature only in CH…
-
does "Away" mode (geofenced) override manually set room temp?
Following scenario: room temp was manually set to 22 degrees C "until next time block". Shortly after, all users left the house for several hours. It appears that even tho geofencing set Tado to "away" mode, the room which was manually set to 22 degrees prior to leaving, remained as such, and did not switch to the away…
-
Value of central smart wired control stat if SRV on all rads
Setting up my Tado and finalising what need to buy. Thinking of setting up SRVs in all rads. If so can’t I create zones as I like, so what’s the point in replacing the old wired thermostat for a smart one.... just leave fully on and each room can call for heat based on needs and schedule in that room ? many thanks. what…
-
Erratic Smart Heating
Hi there, We have a smart thermostat. Over the past week or so, it seems to be erratically setting itself to manual temperatures. We have found it at 5 ℃, 8 ℃ and 25 ℃ - all of which are values we would never set it to. One time, we saw that the display was rapidly changing values without us touching the unit. Can anyone…
-
Combining Smart Controls in one room .. making one master.
help ... New to all this. set up smart control valves on both rads in big attic space ... seems to think they are each in separate room .. how do I combine and make one of them the master ? hekp appreciated. james