-
Wifi geofencing
It would be good if there was WiFi only geofencing. There is not point to keep GPS up whole day and drain battery. I know it would limit app to on and off rather than vicinity check but there is few benefits for me from GPS geofencing as home members keep turning GPS off to save battery life thus geofencing do not work as…
-
Worcester Bosch Greenstar 4000 System GR4700iW 12 S NG system 12kw
I am planning on purchasing a new system boiler, Worcester Bosch Greenstar 4000 series 12kW its got some very good green features of being able to modulates down to 1.9kW central heating output. I also plan to have a 250L unvented tank. https://www.wolseley.co.uk/product/worcester-greenstar-4000-system-12kw/ The Worcester…
-
Integrate Enerqy IQ with smart meters
This interface is technically possible - as an example the free Loop app already connects to smart meter data and manages it well..... https://loop.homes/
-
Tank Oil Level Guage
Hi guys, I'm not sure if this has been suggested before or not but I think an oil level guage in the tank that supplies my heating system that links back to the app would be a great inclusion Not only would it alert you when the oil was low but it could also estimate how much oil you have used each month and work out a…
-
Choose if you want TRV to turn boiler on
I would like to have the ability to disable a TRV turning on the boiler when room temperature drops below its setting. This would allow service engineers to flush the heating system without the boiler being turned on. It would also allow the TRV to act in “dumb mode”, stopping a room from over heating but stop it being…
-
Smart boiler pressure gauge
Please create a smart boiler pressure gauge so that we can view boiler water pressure in the Tado app. I would like to get a notification from the Tado app if water pressure drops too low. Many thanks for your consideration.
-
Ticket system for support
Have searched but only reference I can find is someone who suggested but it was never actioned. Issuing a ticket works well on other sites and enables tracking of a question. I made request for support days ago and received no response. Only means I have of chasing this is repeat the original request. For me the present…
-
Home Assistant boiler data/control
It would be nice if the data/control to en from the boiler would be integrated in home assistant. This would give a better image of how much gas we are actually using. These info would make nice graphs. Knowledge is power!
-
Set Max opening on thermostat
I would like to be able to set the max opening to ex. 40% for a thermostat. As it is now, the thermostat often opens 70-100% which results in very high return temperatures on the water. This is a problem because I pay an extra fee if I send 40+ degree hot water back into the public net. It would help if I could control the…
-
Configurable Boost Timer
Feature request: to be able to set how long the boost heating button should last for as 30 mins can be quite shotr especially if you’ve been away and are heading home outside of set heating hours.
-
Much better support for making a regular water-based underfloor heating system to smart
Hey! It is really good about tado, that you can make your regular radiator into a smart radiator with a device without having to change the system or even call a repairman, but I feel to make a regular water-based underfloor heating system smart by tado is much more complicated. I think I have a typical setup: The easiest…
-
Opentherm : Visualisation of all of the command sent and received by TADO
In TADO pro APP it would be great to see what actually TADO is sending to the Boiler and also the data that TADO is receiving ans needs. I would help greatly to analyse the flow of data back and forth. I am sure that those data are available and used by TADO for Service. There should be also a log file somewhere but I…
-
Custom Boost Settings
Could you please add the ability to set a custom time and temperature to the Boost Heating All Rooms function. Unfortunately a Boost for 30mins at 25deg doesn't even get my house close to 18deg during cold days. Having to either remember to hit Boost again at 30mins or go through every room thermostat to set individually…
-
Smart Profiles for Rooms
What do I mean? Some of our rooms aren’t used much. For example the guest room. But when someone visits it’d be nice to switch that room to a saved profile, rather than create it from scratch, and then delete it again after the guests have left.
-
Saving Smart Profiles
I know that “Home” and “Away” are basically profiles but I think it would be useful to have more. For example I’d like to save my current settings as a “Winter” profile.
-
"away" setpoint range
Use tado to run Samsung heater pump. Wish I could set away setpoint as low as 8C. 8C is the Samsung remote control lowest setting. As of now I make a time program, which in intervals 24/7 switch on and off the heater to average the temperature and keep room frost free.
-
Integrate with "Loop" or add smart meter display
My Smart Meter display is ancient, I installed "Loop" which clones the display, and I now have easy to read information that will track tariff changes on my phone. If TADO included "Loop" integration with the IQ feature it would be brilliant.
-
Floor heating -> Open Window Detection = keep current heating setting
Hi, open window detection works fabolous for me in terms of recognizing open windows quickly. However, for floor heating, the action of switching off heating for a short 5-10min ventilation of a room does not make a lot of sense from my point of view since the floor heating is anyhow quite slow in reaction (compared to…
-
Labels for devices
I have a single room (the kitchen) that has multiple radiators in it. I have smart switches on all of them. It would be useful to label the switches, ie “Radiator By the Window”. That way when the battery is low it is easier to know which one it is.
-
Adapter for Danfoss RA
If you want your Tado thermostat assembled well on a Danfoss RA valve, please do yourself a favor and buy at the same time an extra metal adapter (eg Heimeier type: 970224700 for appr €10,-). This is the best way to fixate the thermostat. Tado's plastic adapter is rubbish and the helpdesk is playing stupid instead of…
-
Modalita away programmabile
Modalita away programmabile giornalmente come avviene per la modalità home
-
Black cover plate
You cannot buy a black cover plate, perhaps there are more people who would like it and maybe then they will get them on the market
-
A configuration option to delay geofencing (returning home)
I propose a configuration option to delay heating (when automatic geofencing is used) when returning home. This could be useful for single person households where primary mode of transportation is cycling. Rationale: Most of the time I travel by bike. When I return home, heating is not necessary for about 30 - 60 minutes,…
-
Better block temperature indication in the schedule.
I thought it was great that the schedule had blue blocks for when I wanted it cold (at night and while at work) and orange blocks for when you wanted it warm, nice and easy to see what's going on. But then I saw that the warm block were set to 25 and thought that was ridiculous, so I set them to 18, and suddenly it's all…
-
add name to devices
hello, it would be nice to be able to de a name to the devices in a room. for the moment we find the number there would be more understandable if we could add a name
-
Manual adjust graph axis
I would like to be able to adjust the axis of the temperature graphs in the Tado app. Currently this goes automatically hence graph axes jump every day and is different for each room. That makes it difficult to compare different days or rooms and makes it difficult to observe how quickly a room heats up or cools down. I…
-
Energy IQ to take account of hot water
I find the energy IQ quite useful but it would be so much better if it took into account the gas usage for heating hot water. Can this be implemented so that energy usage for hot water can be shown both separately and combined with heating?
-
Fix bug where manual timer for heating changes does not work
Expected behaviour: GIVEN a room has a timer set for ‘Manual control on Tado device’ under settings/rooms and devices AND the room is currently running its standard schedule (ie there is not a manual adjustment currently running) WHEN the user makes a manual adjustment to the temperature for that room THEN the manual…
-
Average temperature of multiple thermostats in same room
In a large room with multiple radiators/thermostats, it would be good to have the option of using the average/weighted temperature instead of having to choose one device.
-
Better overview of all schedules in one view
I’d find it really useful to have an overview of all the schedules of my smart valves so I can see when the heating generally kicks on and off to be able to review my system more efficiently. At the moment I have to check every valve individually just to see I’m when everything turns off and on in order to refine my setup