-
Low battery heating demand should show on Care and Protect
When the low battery condition is triggered, the "care and protect" function says that the heating is not on, but it clearly is. The care and protect function should show, preferably, a message saying "heating demand due to freeze protection for room/valve change battery", or even just "heating 100% room".
-
Low Battery Heating Command should take outside temperature into consideration
In a low battery condition, the smart radiator valve seems to command heating, presumably to avoid potential freezing when unattended, however, this is unnecessary when outside temperatures are high (like today!) - the defect/feature request is to disable this behaviour when the outside temperature is above e.g. 5C I kind…
-
Decouple from cloud please
All we want is to avoid this: https://arstechnica.com/gadgets/2022/04/shameful-insteon-looks-dead-just-like-its-users-smart-homes/
-
UI improvement
I think I’ve said this before but I wish there was a way to have a master temperature as opposed to setting each individual block.
-
Energy IQ - Usage is not based on actual meter readings
We were away from home for about one week and wanted to try an experiment with usage data. Our heating was in away mode throughout and did not switch on. I submitted regular meter readings within Energy IQ at the start of April, then on the day we left, and as soon as we returned, and on the following day. The meter…
-
Multiple Internet Bridges - and long standing bug bear... a new idea / approach.
We have major issues with range from the internet bridge, as there can only be one. Clearly it would be simple to slip a simple SSL IPSEC tunnel into the bridge architecture and make changes in the cloud to allow multiple ones on a single account. But this is not clearly the case. Equally being a powered unit, you might…
-
TADO heating/hot water controller error messages - viewer
We have been using TADO for 2 years, and recently upgraded with a TADO Hot Water/Heating controller unit. The installation was done by professionals, and it all works... .. Except that the unit has the triangle warning light almost permanently on?! No amount of fault finding and re-checking can seem to diagnose why it is…
-
Hot Water 'Boost' Button - 30, 60, 90min options
We have been using TADO for 2 years - and its worked well, and so recently installed the Hot Water head unit. We find that there is a big need to have a quick way to turn on the Hot Water for just enough time to heat the tank for one bath/shower or to heat the tank for a couple of bath/showers and then possibly even…
-
Activity lights on home page
I would like to see the H/W and C/H lights that are on the wireless programmer mirrored onto the home page of the Tado App. This would allow a quick view of the current status and not take up much space on the Home Screen. It could also be improved if the C/H was red dot for fully on and amber dot for a remote thermostat…
-
Stats in the web browser + Fix weather on off toggle button
Hi, Can we have the stats available via the web interface? Also on the stats in the Android App the Outside Weather toggle button is the wrong way round to the Heating on and Humidity button, if you toggle them on whey go grey yet grey on the weather button turns the weather off.
-
Can you not have a Forum for tech issues
The guys at the shop do seem a little under pressure. Keeping a website uncluttered is always good but I’ve just spent (Typ waiting time 30 min.) a significant time trying to get a data sheet/ engineering evaluation of the Rad controllers they don’t appear to have one ( the eng/evl I can understand but the data sheet ) ?…
-
Modulation for Worcester Bosch 8000 series
Its now 3 years since Worcester Bosch launched its 8000 series. Can we have modulation compatibility for this series?
-
When in thermostat - At desired temp switch to Fan instead of turning unit of
Today the Tado turns the AC of when going outside temp range. It would be better to go over to Fan mode to continue to circulate air
-
Individual geo location feature
Hi, i let out rooms of my house. I want to be able to turn off their thermostats when they are not in the house. So it would be nice there where user management in the app... HIGHLY MISSING!!!
-
max temp
I have people living at my house and they ALWAYS put the temp on max - please add feature to set max possible temp to fx. 22 degrees or so...
-
Wi-Fi dropping out - and not communicating with all products in household.
Hi, Not sure if your Tado customers are aware that the problems they are encountering, are quite easily solvable 99 times out of 100. I had the same problem when I installed a Ring door bell, the wi-fi router was at one end of the property and the ring door bell was at the other, and I could not control the Ring door bell…
-
Wi-Fi Concern
Hello, If the wi-fi goes down in the property, does that mean you are not able to turn on the central heating in the property? If this is the case, I think this needs discussing by your community members, and needs this feature adding to your system. We have friends in rural areas where the wi-fi can be very intermittent,…
-
Wireless Smart Thermostat
Hello, I would like this feature to be considered by your community members - To be able to turn on all radiators in the property at the touch of a button on the wireless smart thermostat, as you can on the App on a mobile phone/tablet - (Boost Heating All Rooms) - this to me is more convenient. At present the wireless…
-
Tado 3-Way Controller
It would be great for Tado to develop a replacement to a 3 way controller. I have 2 heating zones and a DHW. Tado wired thermostats and radiator valves control the heating zones, but the 3 way controller has to be set so the heating is 'Always On' for Tado to control them. The water is still programmed by the 3-way…
-
More than one setting for each room
I have two rooms for which I regularly change the settings. I would like to be able to have two alternative settings for each room so that I can switch between the two and not have to completely reset the room each time.
-
Naming radiators
I have a number of rooms in which I have more than one radiator but all connected under one Tado “room”. It would be good if each individual radiator could be named eg “under the window” so that one knows which battery to replace without having to say Hi to each radiator. This is particularly important when the radiators…
-
Add undo button to scheduler
It is very easy to make a mistake when designing the schedule which accidentally deletes all the changes you've previously spent time making. Please can you add an undo button to undo whatever you did last. This could go next to the copy paste buttons quite nicely.
-
Support for UFH pumps
I have a single room with underfloor heating and would like to switch the manifold pump when the room calls for heat. This avoids inefficiency from circulation when the boiler is off. Ideally the pump would only be enabled when the room calls for heat, but it would also be okay whenever the boiler is on. I would prefer to…
-
.set all rooms at same time
Add a button that will reduce the temperature by 1 degrees at every press and another the minus 1 deg. So you can set your complete system up or down at a touch
-
API Integration for Energy IQ
I use the energy provider Octopus In the UK, and they provide me with an API key for my account that can be used for getting meter readings and other things. It would be so good if, in Energy IQ, I could put in the API key so that the meter reading were added automatically.
-
Energy IQ calculation behaviour
The calcul for "Hestimate heating consumption" should be include the fix price of a monthly gaz plan. Overwise the amouth in euros can not be correct. Example with the French case: We have a fix price in addition to the volume of gaz they use every month. March, I had to pay 19.30 euros (monthly plan to have access to the…
-
Boost by 5° not up to 25°
I have my heating relatively low but if it dips a few degrees and I want to boost it I don’t want to boost to the maximum 25. 5° more than the current temp would be enough. In this age of trying to be energy efficient and a fuel crisis maxing out the temp is illogical
-
Show energyIQ in GBP
Show consumption costs in GBP in energyIQ
-
Create limits for heating
To create a limit for the heating for when someone is staying over
-
make geofencing free.
I was always surprised that geofencing needed a subscription. When receiving this email below. Geofencing has a much bigger impact. So make geofencing free. "Take action now to reduce energy consumption in a joint effort Hello Robert, Did you know that lowering your home temperature by 1°C will reduce energy consumption by…