-
Connecting Tado to Glow Worm Ultracom CXI 30 Combination boiler.
I have purchased the v3 smart wired thermostat kit to replace a Boss Therm BR1 receiver. There are four wires going into the BR1 in the existing setup: Live/Neutral and then L1 and LX - there is also an empt L2. I’ve tried to connect to NO and COM then park the Live and Neutral. It boiler in always on more as per manual…
-
central heating is on while all rooms turned off
Hi, The new app has the "turn off all rooms" button. As spring have started here and we had some warmer days I used this feature last week, I turned off all rooms. And all rooms staid unheated but ... I have two radiators in the kitchens utility area that don't have Tado thermostat valves on them and those got VERY hot.…
-
New installation - don't know what I need
Hi Muppet I may be but it's just not clear what I need. New installation of Worcester Bosch boiler, unvented hot water cylinder, one main wet UFH zone in kitchen / living room, one bedroom with 2 rads, one bathroom with 1 rad. No existing control infrastructure. All new kit. Please help. What's the best set up? Thanks
-
How to prevent dangerous situation when Tado devices disconnect when heating is turned on?
During my absence, I was warned by my neighbor about a very high temperature in my apartment due to constantly burning central heating. Because I was not at home any manual action was not possible. I asked my neighbor to turn off the power to the central heating. Tado support reports me that my Tado devices got…
-
Before I rip it all out....
I see loads of people on here with same problem ie system doesnt not call for heat. App says everything is connected and fine. Boiler is fine. I have metered the relay and its 100% the tado not throwing its relay. One thing also others have not mentioned is it does not trigger the fault detection either on the app. One…
-
Is the V3 Thermostat an upgrade on the original
I bought the Smart Thermostat Starter Kit back in 2015. Is the latest V3 version an improvement on the original? So is it worth while changing the thermostat to the latest version....does it do anything better? Thanks for your help.
-
Tado keeps heating the room
Good afternoon everybody, I used to have a Honeywell manual thermostat and setting the temperature worked perfectly. Now I had a company install a Tado heating system and since then I have experienced problems. The heating system does not stop warming up the room. In the living room I have 4 heating systems without an…
-
How do I get my radiator thermostats to start the boiler?
Hi there, Sorry I know this has been discussed before but still need some help. I currently have a V3+ smart thermostat wired where my previous thermostat was. I also have an extension kit for the hot water. I have numerous radiator thermostats as well. All of these are paired to the bridge and I’ve created multiple zones.…
-
Can I control two radiator thermostat with a smart thermostat?
I have an open room with two radiators - each with a radiator thermostat. I want to be able to use a smart thermostat so I only have to control the temperature in the entire room through one device. Is this possible?
-
Smart Thermostat Permanently calling for heat
Hi everyone, This is slightly different from everyone else's fault regarding calling for heat when not required, so thought I better to start a new thread. Like a lot of you, I have heating coming on all night, even though every Radiator Thermostat and the Smart Thermostat are well below the temperature. I checked and…
-
Underfloor heating
Hi, About to install wet underfloor heating in a new extension and put engineered wooden boards on top. Have kitted out my house with Tado throughout so would obviously want the u/f heating also to be controlled via Tado. Tado says this can be done by creating a new zone with a zone valve and having that controlled by a…
-
HomeKit Features missing?
Hey, am I missing something or can Tado only control temp and on/off in HomeKit? I see humidity is hidden in the settings tab but no way to control fan speed or the dry setting of my aircon… am I missing something or is it just not supported?
-
Global On/Off feature disappears randomly
The global on/off feature that was added recently seems to randomly appear and disappear for me on the Android app. Its becoming quite annoying as I can't turn off/on heating until the option randomly appears again. Anyone know why it does this? I get the impression it's being controlled by Tado servers and if the app…
-
Two heating scenarios - how smart Tado° is?
Would Tado° take a different approach to the way it heats your house in below two cases (without Early Start option enabled)? Outside temp: 3 °C, Partly Cloudy Outside temp: -3 °C , Snow
-
Radiator Thermostat not working out of the box!
Hi - i have raised a ticket to Tado but just wondered if anyone can help? Just bought 6 radiator TRVs and after installing 3 without issues the fourth appears to be faulty. After removing the battery tag the unit does not boot up or show any lights. I switched the batteries and they arent the issue - the unit is. Anyone…
-
Replace Honeywell TH8200G1004 with Tado
Hello all I have just bought the Tado kit and I am wondering how I can do the wiring to replace the existing thermostat. My heating is from a public heating system provided by the city, there is no boiler in the house. Attached is the current wiring, it is quite simple but I am not sure how to proceed from here, would not…
-
Wireless Temperature Sensor: asking questions, seeking opinions
Well, I must have missed the memo because I completely missed the arrival of the Wireless Temperature Sensor. This seems to be the missing piece of kit that I have be looking for, so I have some questions and I seek your opinions. I currently have a single Smart Thermostat, the only control I have otherwise is TRVs. For…
-
What to buy: Separate hot water timer, 2 zone/2 thermostats heating
Dear all, I have hot water running from a timer (Danfoss TS715Si). Then in one level of the house, a switched/wired thermostat (Danfoss TP5000Si). And in a second level of the house, a second switched/wired thermostat (also Danfoss TP5000Si). What should I buy? Smart Thermostat kit with Hot Water. Is the thermostat wired?…
-
Extension kit compatible with worcester bosch 30i digital bus
I have purchased a tado wireless thermostat starter kit. I want to use the digital bus but the wireless receiver does not have the digital terminals. Will an extension kit v3p-ek01-tc-ml-01 contain the digital bus terminals?. Will I be able to use this extension kit rather than the wireless receiver for gas modulation with…
-
Hot water not working properly in google home and alexa
Why can't I set the hot water temperature to more than 32 degrees celsius while I am using Google home for my tado?
-
Missing outdoor air quality
I’m missing outdoor air quality index. App only shows outdoor temp. Anyone else? Workaround?
-
Buderus EMS
Hello, could someone share wiring for Buderus EMS - Extension kit and setup parameter in thermostat. Thanks
-
How to add the AC into Apple home kit?
:# :# I did a successful to join my Home kit when first time enable, then I remove it from my home kit and Tado app. Then, I try to rejoin the my Apple Home kit, but always told me the device has been added to another family, but I just purchased it yesterday.
-
AC Fan Speed Control is Reversed
Hi, I live in Taiwan and I have a few Hitachi Mini-Split ACs (RAS-36JB/RAS-28NK/RAS-25NL), they all work fine with Tado using command set AS-120. However, I just realized lately that the fan control in the Tado app works in reverse of the actual AC fan speed. Meaning if I set it to 1/3, the fan blows the strongest and 3/3…
-
Installation of Tado kit
Hi all. I purchased a Tado wireless heating control with hot water quite some time ago and have been struggling to find someone to fit it. I’ve been let down by 2 different electricians now who I can only presume don’t want to do it, or are just plain unreliable. I know Tado suggest that it can be done by the user, but I…
-
Glow-Worm smart wiring centre
Good evening, I bought the Starter kit V3 and 8 smart radiator thermostats a couple of months ago and have just got round to attempting to install. To my dismay, it doesn't look like Tado is compatible with my current setup which is: Glow worm Ultracom2 sxi 12 boiler Glow worm smart wiring centre Hot water cylinder 3 way…
-
Is tado supported by valiant ecotec pro 286
Can I use tado with my new valliant eco tech pro 286? If so, which connection should I use for wiring, analog/relè/digital? Thanks!!
-
Is it a bug or a feature? - 'heating to xxx' & temperature increase only by 0.5°C?
Both the app and the web should not say 'heating to 20.5°C' if it is 20.6°C already. I can manually change the status or reset it, but why? Tado° should be smart enough to work this out? This is happening with Smart Schedule set to 20°C. This is creating confusion – the boiler does not heat anything and should not as there…
-
Change WiFi connection
How do I change the WiFi connection the device is currently connected to?
-
Re: Away mode will not turn off heating