-
Is "Wireless temperature sensor" the same as "wireless thermostat"?
Saw in the eshop, is the add-on wireless temperature sensor the same as the one that bundled into “ Starter Kit - Wireless Smart Thermostat V3+” ?
-
Confused about devices
Hi, just starting out and find the products confusing. For hot water there is an extension kit and a wireless receiver. It seems only the former is opentherm compatable, the latter requires re-wiring (not a standard UK backplate)? Wireless thermostats and sensors have the same model number with interchangeable…
-
Required setup
We have an Ideal LOGIC COMBI C30 boiler and two wired Danfoss controllers (one downstairs and the other upstairs) that are independent of each other. My question is quite simple - what actual tado hardware (excluding the smart radiator valves) do we require to: a) get the system up and running in the first instance (will…
-
Does Tado need auto-assist
Auto-assist is a paid for subscription but after i installed the app on my phone before installing the kit. I had geo fencing asking me if i wanted to turn off the heat. And after installing the kit i moved the thermostat and tado told me it detected an open window. Both of these happened before i started the trial of auto…
-
Extender no longer available?
I've just bought a starter kit with a wireless receiver - this seems to be the only option now in the UK. However this only appears to support relay on/off, whereas the extender (as far as I can ascertain) supports OpenTherm and eBus. This is what attracted me to Tado in the first place! Is this correct? If so, how do I…
-
What adaptors do I need?
I'm trying to install tado but I can't seem to find the right adaptor. I use the danfoss adaptor (the thermostats are danfoss) but I keep getting error 2, because I think the pin is too far in. Have you had this situation? how did you solve it?
-
Smart Radiator Thermostat anomaly
Am i being crazy and misunderstanding? I have my temperature set on one of smart radiator thermostats (kitchen) in one of my rooms to 14.0 degrees. Minimum away is set to 13.0 degrees but home screen of the app is showing that the temperature as set to 13.2 degrees and actual temperature is 14.1 degrees . Why am i getting…
-
Zone control advise
Hi, I would like to gain zone control of my current setup. Prior to tado I could heat ground or first floor zones independently via a wired thermostat in each of these zones. So getting that again and independent control to heat just the bathroom too is my aim. My current system comprises of the following: Tado wireless…
-
Option to have value Fully Open
As you can only set temperature to a maximum 25°c, after that can we have a fully open valve option. Yes sometimes some of us want hotter than 25°c
-
Wiring
Hi everyone, I have an existing Tado system that powers all my standard heaters. Now I want to replace the thermostat of my underfloor heating, but I am a little confused how to attach the existing wires to the new Tado thermostat. On the old Thermostat there are three wired connections: "N", "LOAD" and "L" What do these…
-
Bathroom Underfloor Heating
Hi There, The last zone in the house is getting the tado treatment. This is a downstairs bathroom with wet UFH. The thermostat is outside in the corridor. Obviously, a wired 'stat is going to measure the temperature of the corridor and not the bathroom. If I use a sacrificial TRV, or even a wireless temp sensor, how can I…
-
Able to shut off downstairs rads while upstairs ones on?
Hi all, I just want to verify I can do the following before I shell out for the extra radiator controllers and thermostats. Currently I have a Tado wireless smart thermostat working great. I have a log burner and open plan downstairs. When the log burner is on, the whole of the downstairs is warmed from it, but upstairs…
-
Can I replace a 3 zone programmer and wired stat with wireless?
There is a bit more it than my initial question! I have a tricky system and not sure what hardware I need, so am hoping someone can help! I have a oil boiler that heats two buildings. I only want to ‘smart’ building 1. It is a Pressurised system with mega flow for the hot water. I have a three zone programmer that controls…
-
Auto geofencing?
Since Last Sunday (7/11/21) the geofencing on my app hasn’t been working correctly, for some reason it doesn’t automatically set me to away when I’m away from home I have to manually set it but it will switch back to home automatically when I return home. I haven’t had any software updates I have gone through my background…
-
Room with smart thermostat combined with smart radiator thermostats
In a room I have already a smart thermostat who is controlling the temperature and 4 radiators. I should like to equipe the radiators with smart thermostats and place them all in the same group as that smart controller. Q1. The smart scheme is set to 21°. What will happen if the smart controller detects 20° and in the SRT1…
-
Thermostats call for heat after temp has been reached?
I’ve only noticed this recently. For example: Thermostat is set to 18C App reports room is 19.5C and heating to 18C Why is this?
-
Ghosts in the machine? Rebooting the wireless receiver.
I've had my Tado system installed for a few days driving our new ground source heat pump. I have the wireless receiver wired to the heat pump with several smart radiator valves and the wireless temperature sensor. Due to poor connectivity I've moved the bridge up into the loft, hanging downwards and with a foil backed…
-
Replacing v1 thermostat with an v3 extension box
Hi, I wonder if anyone would know how to replicate the wiring on my v1 thermostat on a v3 extension box. I'm a bit confused as I only seem to have 3 wires! This was done a few years back by an installer. This is the back of the extension box. Thanks for your help in advance.
-
Installation of New Tado system with 15 Smart Radiator Thermostats
Dear Community, Have recently purchased a new amazing Tado system and have three installation questions. I am very keen for our new Tado system to maximise energy savings, utilise the full feature set, access reports to show others the savings we have achieved and ensuring the system is installed using “best practice”.…
-
Smart Radiator valves
Don't know if I'm alone in this, or whether this question is on this forim, but just fitted a full Tado system to the 20 radiators in my house, and particularly where there is no noise absorption, ie curtains, the noise that the valves make when opening/closing/ adjusting, can be heard, just about through the whole house -…
-
How to configure this set up?
I have a system boiler with wired programmer that controls the hot water (tank) valve and central heating (radiators) zone valve with a wired thermostat. I have a separate zone valve for wet underfloor heating that has its own wireless programmer and thermostat. I want to use Tado to replace everything, that is, the wired…
-
Which Starter Kits/ Add-ons do I need?
Hi everyone, I have a new build with a two zone heating system (upstairs & downstairs). I currently have two Honeywell CM707 (wired) thermostats. Which kits would I need to replace both of these with Tado thermostats? Would I need two wired starter kits? or one wired and one add on? Thanks in advance! Ash
-
Location of Tado thermostat
I have a three storey town house. The thermostat is hard-wired in the living room on the first floor. There are 4 radiators on that floor. The ground floor has two radiators (hall and kitchen) and is very cold. Would I be better relocating the thermostat to the hall and fitting tado radiator valves on the first floor?…
-
Not sure what I need!
I have a tricky system and not sure what hardware I need, so am hoping someone can help! I have a oil boiler that heats two buildings. I only want to ‘smart’ building 1. It is a Pressurised system with mega flow for the hot water. I have a three zone programmer that controls the rads, water, and the wet ufh in the main…
-
Radiator thermostat failure
I had my first radiator thermostat failure today. Woke up to find the bedroom radiator warm, even though it shouldn't have been. Turned the thermo off and it couldn't stop the water flow. Removed it and checked the valve and that worked fine. Replaced the batteries and it still couldn't stop the flow. It was working, and…
-
Heating still on
Heating was still on last night and got extremely warm in the house. It should of switch off at 21. It finally switch off at 22.2 Why? I have noticed that this is a common issue, is there a fix.
-
Hi. I have a Tado system that controls my boiler for hot water and heat
If my radiators are hot because the smart TRVs are on Will the TRVs force the boiler to turn on. At the moment the boiler shows off on the app but the radiators are on and show as on in the spp
-
No previous thermostat
Good morning, I recently moved in an apartment that has a tado thermostat (to configure). Unfortunately as part of the installation, it is required to share which one was the previous thermostat or controller and I have no idea of what it was. I tried to proceed through the steps without including this, but at the moment…
-
eurodate com
-
Can I use the wired Smart Thermostat with my combi boiler?
I have a Worcester Bosch Greenstar 25i combi, currently operated by the Greenstar Comfort II wireless controller. I would like to replace this with a Tado setup - however, I am unsure exactly what equipment I need. My current thermostat is wireless, so this would suggest I need the Tado wireless Smart Thermostat. However,…