-
Multiple Boilers
Can Tado be installed to service two boilers in the same property. So two smart thermostats with hot water control and run from the same acct? Has anyone done this? Was thinking could setup each on a separate bridge but set each one up with the other powered off ?
-
Advice on smart wireless installation
Hi, I'm pretty much sold on picking up the Smart Wireless thermostat. I want to DIY install, but am after some advice before proceeding. I have a Honeywell ST6400C programmer (controlling central heating and an unvented cylinder), and I think the short story is that I will be replacing this with the wireless receiver.…
-
Wireless control for underfloor heating
Dear tado community, I have a room with underfloor heating which currently is controlled via a manual control valve at the manifold (the manifold is located elsewhere in the building). I intend to replace the manual control valve with an electric actuator, which should be straightforward. However, since I have no cable…
-
Daikin heatpump, floor heating and tado
Good day everyone, I have a daikin altherma bluevolution 6kW heat pump for several months now, next to it I have a 300 liter storage tank. My house has 3 floors with radiators and underfloor heating. (1) ground floor : floor heating with temperature regulator knob and a tado thermostat (no tado heating knob). (2) 1st…
-
HomeAssistant entity control features missing after upgraded the tado firmware.
HomeAssistant entity control features missing after upgraded the tado firmware. Before: Tado: Firmware: 59.6 ------------------- After: Tado: Firmware: 118.3 After upgrading the Tado firmware, at Tado have a new feature of my ac: swag and it is working well. But At home assistant and HomeKit, all the control (Fan mode:…
-
Bridging BossTherm receiver
Hot water is perfect but I need to bridge the BR1 receiver to allow Tado to control heating. Any idiots guides. Still waiting on Tado getting back to me. There are only 4 wires going to the back of it two brown and two blue. How do I bridge these and what do I use to do it? Thank you
-
Wiring question
Hi, I have a Baxi Assure 30 currently wired to 2 Danfoss TPone thermostats. I am replacing them with tado v3 wired starter kit but the wiring points are different. I have N01 and N02 used in the current Danfoss controller but only seems to be N0 in the tado. The downstairs controller also controls the hot water system. Can…
-
Schedule different to plan
Hi, brand new to this system. My App is showing the next change, to 18⁰ at 21:00, when I have set it to 5⁰ from midnight till 07:00. Programmed time to off is 21:00. Any idea where its picking up the 18⁰ from and how i change this? Is this some sort of default mode, do I need to add another time profile from 21:00 -00:00?
-
How to increase hot water temperature
My Tado wireless unit is newly installed. I am only getting lukewarm water from the hot water system. How to I get it back to the right temp (about 60 C)
-
Internet connections
I have two internet networks at home, one is Sky and the the other is Orbi. My question is if the network bridge is set up on one, does the receiver and all the TRVs etc need to be on the same network?
-
Manual change to hot water schedule
On the “Manual Control on Tado device” I have timer selected and set to 30 minutes but when I turn the hot water on for a boost it continues to the next schedule change. Is there something I am missing or a system wide problem. Thank you for any help.
-
No connection from smart radiator thermostat
Hi I have been trying for 3 days now to install the new Tado system onto our boiler. An electrician hand plumber have installed the kit and I’m trying to connect all the thermostats to the bridge. It’s not working. No pairing or EO or 3 lines as per instructions. We are stuck. Help is non existent from online chat. No…
-
Internet is a must requirement for operation?
Hello. I have a few properties available for rent, but please note that some of them lack internet connectivity. However, I can use my phone's internet to download all the necessary software during installation. The key question is, is a reliable internet connection essential for day-to-day operations or not needed?
-
Newbie
Hi all, just installed a v3 package with hot water controls, can anybody explain what the purpose of the wireless wall thermostat is, as I understand it the wireless radiator valves control an individual room’s temperature.
-
Multi trvs in a zone
Hi. Hope someone can advise on this! At the moment two of the zones in my home consist of one trv (zone 1) in the downstairs loo and two in the conservatory (zone 2). The trv in the loo keeps going offline because (I think) the wi-fi signal in there is weak. If I added the loo to the conservatory zone would that overcom…
-
Heating system tripping electrics
Had tdao system installed for years, Last year had to buy a new starter kit. Togiht heating system started tripping the electrics - so had to switch off. I have Bridge, Hot water controller, Wireless themostat, and 6 radiator valves. Might not be tado related, but where do i start in trying to work out what part of the…
-
Cam Kam Me You
How can I access 4 locations on one app?
-
Swapping from system boiler/cylinder to Combi
Hi, I currently have a system boiler setup with my tado controlling the heating and the hot water to the cylinder. An engineer is coming to wire in the tado to the new combi boiler. Do I need to notify tado of the change of configuration or will the system just recognise it? I’m guessing the new wiring wouldn’t allow any…
-
manual change on the knobs
Hi, I just got my Tado equipment installed, and I noticed if I do change the temperature manually from the knob itself, it doesn't update on the app, is that normal or there is something I'm missing here?
-
Honeywell ST9100c & CM707 Integration - Single Zone
Hi Community I've recently moved house and taken my tado kit with me. I'm after some support in getting setup. Here's what I have: Tado wireless receiver Wireless Room Stat 13x Radiator Internet Bridge My house has the following: System boiler ideal logic system s15 Honeywell st9100c HW programmer Honeywell cm707 room stat…
-
Wireless receiver supporting modulated heating + hot water control, for system boiler.
I have an 'Ideal Vogue max' System boiler that supports OpenTherm - their support technicians have confirmed it. It heats the hot water in the hot water tank, plus the central heating (7 radiators, all with TADO TRV's). I would like to use the modulation feature of my boiler for central heating. What do I need? Does such a…
-
Tado AC control
I’ve just purchased a tarp AC control to use with my LG aircon. I was having issues with the temp of the AC being different to the actual room temp and not turning the AC off when a temperature was reached. I was hoping the Tado would do this but seemingly this feature has been removed. Is there anyway around this. The…
-
Lower temperatures wanted for AC unit
I’m using the Tado with an AC unit for both heating and cooling. It seems the lowest temperature I can set is 18 deg C but I’m finding this too hot for overnight use. Is there a way to set this lower?
-
Smart AC (2x) and Homekit “not responding” issue.
I have an issue with my 2 (two) Smart ACs. They continuously go to the “not responding state” in Homekit. They are still reachable and usable in the Tado app itself at that moment though. What works for me consistently as a workaround, is blocking internet access of any ONE, or BOTH Tado Smart ACs in my wifi router. When I…
-
Ideal Vogue Combi C32 Gen2
I have an Ideal Vogue C32 Gen2 and I wondered if anyone could confirm compatibility with Tado? I am also interested in the ease of fitting Tado to this boiler?
-
Ideal Vogue C32 gen 2 thermostat removal
I have revieved these install instructions from tado. All the tado equipment is successfully installed. The old thermostat (shown above) is removed however I do not have any plug in top left corner! There is only one plug, so where do I connect the timer link plug to? Initially everything seemed OK but now my boiler won't…
-
Query before buying
Hello, I just want to check something before I purchase the wired thermostat, I currently have 2 wired thermostats by ESI, one upstairs and one downstairs, I have an Ideal combo boiler and was wondering do I just replace the wired thermostats or do I have to get anything extra to connect to the boiler? The exact make of my…
-
De Dietrich INIDENS Compatibility
Hi Team, can you please confirm Wired Smart Thermostat compatibility with De Dietrich INIDENS heating? I am not able to make it works. Thanks, Ondrej
-
Opinions on potential range issues
Hi all, I have been viewing all the discussions on range issues but this is my first post. I am due to move house next month and in preparation I bought the V3 wireless thermostat starter kit plus 7 TRVs in the Amazon Prime sale. I will not have opportunity to physically test the system until after the Amazon product…
-
V3+ firmware update stuck
Hi, I got wifi easily - device "blinks" with my cell and laptop. If i touch tada it shows temp and wrench -sign after that. Updating seems to be stuck - I'v been waiting bit over an our now.. What to do?