-
Trv
I have got 6 trvs 1 is linked to the room stat ,if i want a specific room rad on is doesnt call the room stat and only comes on wit that specific room liknked to it any way it will work wit any room called for heat
-
Firmware Update taking forever
Hey guys, Just got my Tado Smart AC Control, and the setup has been upgrading firmware for the last 2 hours, on a relatively fast internet connection. Has anybosy experienced this before, or any tips on what should I do? Thx :)
-
Mixing Tado Wired and Wireless stats
Hi, Trying to figure out if its possible to mix a wired thermostat with the wireless starter kit with hot water control? In the middle of heating upgrade where I have 2 heating zones (Z1 & Z2) and a dedicated hot water zone (Z3) Planning to get the wireless starter kit (with hot water) to control/manage the existing…
-
Boiler firing when tado off
Does anybody else have a problem where the room thermostat is at temperature, so not calling for heat, and the controller is showing as off but the boiler is firing? I've got a problem where the boiler fires at 12noon every day for a couple of hours, even though all the tado settings are set to off. The only way to stop…
-
Edit tiles iPhone?
Hi yall, New tado user here. I found a thread about editing tiles from 2020 but it seems it is only possible from a computer? Is there any plans on iOS?
-
Tado Showing Offline
Hi all, Since 4:23am on the 17th of December, our Tado devices have all been showing offline. On the app, it’s showing the Wireless Receiver having no connection. Has a software update recently gone out that could affect this? thanks Lewis
-
No Hot Water or Heating
Morning I installed the extension kit on to my Worcester Highflow 440 CDI yesterday, and was able to pair it up, and everything is showing as working in the app. However, if I turn hw or ch on, nothing happens away from the boiler. This morning, I’ve come downstairs to it, and the ‘pilot’ light on the control panel is on,…
-
Do i have right kit after moving home?
Hi, Had Tado in previous house, Extension kit with wireless thermostat and then lots of Tado Rad valves. It was connected to a gas boiler and unvented cylinder, controlled heating and hot water all good. Moved house and we have a boiler, an unvented cylinder and two heating zones (three if you include hot water), upstairs…
-
How should I set up two heating zones/circuits using OpenTherm
Hi all - long time reader, first time poster... I am having my boiler replaced and integrating an additional heating circuit (of a basement flat I am amalgamating my house with). The boiler will be OpenTherm compatible (e.g. a Viessmann Vitodens 100-W 32KW system boiler) and the two heating zones and one hot water…
-
How do Iset up a time block?
Ive been trying to set up new time blocks without ant success. For instance just now i tried to set up a time block for my A/C to come on at 10 pm and turn off at 6am. It seems i can set the on time to 10pm but when i try to set the off time to 6am it just defaults back to 10.15 pm. I’ve tried deleting all another time…
-
Indirect Unvented Hot Water Cylinder
Hi, Current Tado system comprises of several smart TRVs, an internet bridge and a wireless extension kit, which is attached to my Valiant Combi Boiler. Want to add an indirect, unvented hot water cylinder. My plumber tells me that the cylinder coil will be heated by my combi boiler as part of the heating system, which in…
-
Tado v3+ - OpenTherm - Vaillant ecoTEC exclusive hot water temperature control
In my Tado v3+ - OpenTherm - Vaillant ecoTEC exclusive VHR 25/36CF/1-7 setup - when Tado changes hot water temperature, the boiler still shows temperature installed manually on the boiler itself. It looks like temperature control from Tado does work - I see that it takes much longer until water becomes hot at night when…
-
How to turn on the heat in the house if the phone or internet is not workjng
Hi, I have a ski cabin that is use by other people that do not have the Tado App and some time the internet is not working in the mountain, so my question is how I can turn on the heat using only the wired thermostat or and valve thermostat?
-
Low or dead Bateries signal
Is possible that when the batteries gone dead the Thermostat valve remains in the same position instead of closing fully? I need this for a Remote ski cabin that I can not replace the batteries right away but need that the heat reman on
-
Zone control/schedule without smart TRV
Hi! I'm looking at getting Tado - I have a 3 zone system. I For one of the zones I probably will just stick to dumb TRVs (we don't use the rooms much) so there will not be a smart TRV to tell the zone to turn on when required. Is it possible to set up a zone schedule in the app that just turns the zone on and off when…
-
Incompatible with Worcester TR2?
So some years ago (2016!) I looked into Tado, and got as far as mailing Tado with a note of the heating that I have - "Worcester Bosch Greenstar 40 HE Plus combi boiler which is linked to a Worcester Bosch TR2 thermostat", and was told that it was supported. Finally got tempted to sort things out, and ordered from Amazon;…
-
My bridge seems to switch off until 5am, is there a way to stop this happening please?
I have Hive lights connected to the bridge, might be a reason it does it?
-
Are TRV adaptors available for purchase?
I have two Tado TRVs that I need Giacomini adaptors for, but I don't have the adaptors that came with the Tado TRV. Can you buy the adaptors separately?
-
HomeKit: how to automate
I’ve just set up the Tado v3+ and paired with HomeKit but can’t seem to set up the Automation I’m looking for. Desired Automation: When temp drops below 16°c turn on AC, simple. However when I select the Tado as the ‘sensor’ I don’t have the option to select the same Tado as the ‘Accessory to Automate’. If I use a HomePod…
-
Tado app not working, web login is fine
I have been experiencing no connectivity on the App but website is letting me manage my devices. On the App it just says , failed to connect to server.
-
Boiler occasionally fires with no Tado LEDs on & all devices on App off
We have CH & HW managed by a Tado receiver and Individual Smart TRVs. Both CH and HW are scheduled and work fine during scheduling, with the App showing that rads are heating and / or CH is on and the appropriate receiver LEDs illuminating. However when the heating is off (like now in Summer) and outside of the HW heating…
-
Frost protection and Internet outage
I have just learned that the tado system I have installed is totally reliant on the internet. We are very rural and the internet is frequently going down for a day or more. I can work around that manually when I am home but I am away (as is everyone else in the house) frequently in the winter for up to a few weeks at a…
-
Wireless thermostat flat batteries: why no hot water?
Wireless thermostat with wireless receiver and separate hot water boiler. When batteries are flat, hot water doesn’t work either. Why is that? I would expect the bridge to keep communicating with the wireless receiver, according to the hot water schedule. I don’t understand what the wireless thermostat has to do with…
-
when Smart Thermostat goes offline all smart radiators go offline as well
just installed a smart thermostat two days ago. unfortunately is a bit far away from the bridge so that it goes offline from time to time. however if it does all the other smart radiators in all the rooms go offline as well. that seems a bit strange, since when a single radiator goes offline, that doesn't affect the other…
-
Everything gone wrong after system was drained to fix radiator
I had to have a radiator valve fixed and a plumber came round to to this. I turned the boiler off and he drained the system. When he filled it up again nothing worked. The boiler is on but will not fire up despite both the hot water and heating being on. (I have to have the hot water on to have the heating on as it is a…
-
Tado HW Immersion Heater Relay
hi Tado gang, I have 6kw solar system on the roof without batteries and i would like to heat water using immersion heater during the day when we are at work , instead of exporting electricity back to grid. I am currently considering 2 options. 1 . Myenergi Eddi 2 As i already have some tado devices for heating. I am…
-
Underfloor & Radiators - Urgent help please :(
Hi Guys, Thanks in advance for any help, it really is appreciated. So I current have a Tado V3+ starter kit, which is used to control the central heating in the house. We are undergoing an extension and we are adding underfloor heating to the extension. Ideally I would like to stick with Tado as we've got used to the…
-
Banging in pipe when tado calls for heat
I have the following devices: Smart thermostat RU1784819200. Wireless tempriture sensor SU3477353729. Internet bridge IB0312487168. The boiler is a Valiant ecotec 835 plus. The boiler is working fine and has been for a year now . The smart thermostat has replaced the old downstairs thermostat and controls the motorised…
-
Can't use support live chat - Couldn't send
Ever since yesterday when I try to contact support, I choose "I have a technical question", and it immediately says "Couldn't send". Same if I choose a different option. Using Microsoft Edge on Android.
-
Using hot water control as second zone
I currently have a Wired Thermostat (albeit acting wirelessly) and 6 radiator thermostats. These are all connected to an Extension Kit. The underfloor heating and radiators each have their own valve. However, the valves can't currently be triggered independently (i.e. if a radiator calls for heat, the underfloor heating…