-
Merged: After several years still no range extension?
This discussion has been merged.
-
Merged: support for multiple internet bridges
This discussion has been merged.
-
Notification
Can we have a notification when someone turns heating on please.
-
Additional physical sensors (presence, doors closed) for more targeted routines
Hi! It would be great to have couple of additional sensor types to allow more customised routines: - presence/motion sensor - door/window open sensor These sensors could be additional conditions to the routines, e.g.: - heat bathroom to 23 degrees only when the door is closed - heat Office to 21 degrees Monday-Friday 8-18…
-
Ebus Max Flow Temperature setting (like the one just released for Opentherm).
Would it be possible to do the same for Ebus controlled boilers via the wired Tado, +- settings? My Vaillant can ramp up to 80C if it wants even if I set the max temp lower on the boiler. The ebus will ignore these settings and do what it feels is best. I might only want it to go to 66 or 70C max for example. It's just…
-
Air Comfort
The ideal temperature in a room or zone is a matter of personal choice. The degree of humidity is a matter of climate. These vary and should be capable of choice and customisation not a level of humidity and temperature that tado decides should suit everybody regardless of preference and location. Solution. Allow for some…
-
2FA / MFA - EU legal requirement
Hi, I've created a new post to again highlight the importance of this to Tado. Without 2 factor authentication/MFA, Tado will soon be in breach of EU law. In 2022, the EU Commission proposed the Cybersecurity Resilience Act (CRA) which introduces mandatory cyber controls to, amongst other things, IoT devices including Tado…
-
Relay and Opentherm together
The Tado extension kit can control the boiler through a relay (simple on-off switch) or through the Opentherm bus. The bus allows for better temperature stability and higher efficiency as it tells the boiler to turn the heating up or down as necessary. If a heating system contains other elements, like a shut-off valve or…
-
Make Smart AC Control expose more AC settings to HomeKit?
Is there any reason why the only options in HomeKit are cooling, heating and off? In the Tado app I can see that it knows the commands for auto mode, dry mode, fan mode, fan speed, tilt, fixed etc. HomeKit supports these modes and settings, I don't think it would be that difficult to expose these modes and settings to…
-
Please implement the possibility of disabled the three LED lights of the internet bridge
Hi Everyone, the Tado internet bridge has three very bright LED lights. I would like to have the possibility to disable those LED lights please. A configuration as described below could be useful for all users: by default, after booting, the LED's are also on but in the app and/or the web portal you can choose to disable…
-
Make it easier to see which room is requesting heat by adding a symbol/colour to room Icon
I have a few rooms with smart TRVs and it always takes me a while to find which room is requesting heat. It would be easier if there is a little logo, or maybe a coloured border around the room icon if it is being heated.
-
Automating Home/Away process
Apologies if this has been raised before but I couldn’t find a reference. When setting the system to “Away” provide an option to revert to “Home” either by setting a future date (preferred option) or at least by giving the number of days user will be away. This would save user forgetting or if out of internet connection…
-
Cooling function for Heat Pumps with floor cooling
Please create a function where we can use Tado with a heat pump (equipped with a cooling function) connected to a floor heating system to cool the rooms (with Tado thermostat) to the specified temperature. Each room is equipped with Wireless Smart Thermostat or Wireless Temperature Sensor. The heat pump is connected to the…
-
Merged: Multiple homes
This discussion has been merged.
-
Merged: Manage multiple homes through one Tado app
This discussion has been merged.
-
Merged: Multiple homes
This discussion has been merged.
-
Merged: how to add a second (and 3th) home with Tado to my app
This discussion has been merged.
-
Merged: Second home problem
This discussion has been merged.
-
language for android
Hello, please add language settings for Android in the app
-
Temperature still visible with grouped TRV’s
In my Living Room I have multiple TRV’s, two of them for some reason intermittently lose connection. When this happens I cannot see the temperature on the main screen of the app. It just says the whole room has a fault. I think it would be better if you could still see the temperature of the room on this screen but there…
-
Model number shown in app
Can we please have the model number of the device show in the app, or at very least a serial number lookup on the support site. I have spent two hours so far trying to figure out if I can put NiMH batteries in my radiator valve. The "What type of batteries..." documentation says I can only put alkaline batteries in VA01…
-
Whole House Override from main thermostat
HI, I'm new here, I did a quick search but couldn't find anything. We have an issue in our house which is that I love smart home tech but my fiancee hates it. We have a tado thermostat in the hallway with radiator ones in every room. Our house is quite drafty and cold and sometimes we just need to override the schedule…
-
Combining the best of Tado and Nest?
I realise the title of this post may sound odd or even controversial but here goes. My system is very conventional (read old fashioned) consisting of a 16 year old Viessman 100 WB1 boiler, gravity fed (tank in roof space) and I believe what is called a Y plan layout with separate two-way valves controlling the heating and…
-
Internet Bridge local API
It’d be great if it were possible to interact with the Internet Bridge using a local API so that requests don’t need to be made via the internet. Presumably there’s some kind of http server on the device as HomeKit is able to communicate with it locally?
-
"feels like" temperature setting
21c feels quite different depending on the humidity in the room It would be great if the trv would adjust accordingly, depending on the humidity.
-
Ability to rename device
When batteries are running low I get an email informing me that a particular device in a specific room has an issue. In some rooms I have 4 radiators. I then have to go round ‘blinking’ the stat multiple and watching all the stats in the room to find which one it is. it would be great to be able to rename or give a…
-
Merged: Multiple homes
This discussion has been merged.
-
Mention remove the existing wireless receiver
Hi all, just installed the wireless starter kit v3+. The installation instructions for Viessman Vitodens 100-W B1KC did not say anything about removing the old wireless receiver. It would be nice with a little mention on that :)
-
Merged: Setting to keep the valves fully open in summer
This discussion has been merged.
-
"Summer/Cooling mode" for wall thermostat
Hi there, I have an underfloor heating with a cooling function. In summer, cool water can run through the floor to cool the room. For that I currently need to set the temperature to max (25°C) to keep the thermostats open. If the room temperature would rise above 25°C the thermostats would close and prohibit a cooling…