-
Ability to use Wireless
Tado needs the ability to use multiple wireless temperature thermostats to control different rooms independently.
-
Heating status for On/Off mode
I would prefer to see the heating status as a simple on/off symbol rather than the three waves. I have a heating source that does not support opentherm and thereby only works in on/off mode. Why I would need this: This would be useful to really check if my heatpump is working properly: I currently do not always know for…
-
Increase Zone Controller Max Rooms
I ran into the limit of 10 rooms on one Zone Controller and I need it set to 12 rooms. I am sure this has also affected other Tado users retrofitting a complete house.
-
Postponed buying 8 Tado thermostats, looking for other solution!
Postponed my idea to install 8 tado thermostats, because it appears that, nevertheless many people ask for this integration, still nothing happens. If it comes to brands that cannot be integrated with Smartthings, there are a lot more cheaper ones on the market I figured...
-
Air Comfort suggestions
Hello, We're supposed to make energy savings with Tadoº, but it's quite inappropriate to get a suggestion to turn the heating on when a room is just below 20ºC. The World Health Organisation recommends a room temperature of around 18°C in Winter, and The Energy Saving Trust advises setting the thermostat to around 18-21°C,…
-
Boiler demand indication on main page
Hi, it would be great to have the three waves or just a simple red dot by the temperature of each room in the main page. Or at least a way to see at glance if any of the room is forcing the boiler to run. Thanks
-
Simple improvement to use Tado both for heating and cooling
More and more users are moving to heath pumps both for heating and cooling, by having the same pump satisfy both needs by pumping fluid under the pavement. Unfortunately, so far, Tado only has a minimum temperature in his controller, so it is only possible to employ it for heating. A simple improvement would entail adding…
-
White text on grey background (Temperature graphs in dark mode)
I'm using general dark mode on my device (Android) With the the latest application update the inside and outside temperature display has been changed from black text to white text (on a light grey background. The text has become unreadable. Can you change that back please ? Edit: additional info, In normal (non dark mode)…
-
Hot water boost
Can we have a hot water boost facility that is timed. Having to let the boiler run until its next schedule is un necessary and wasteful should you forget to stop it.
-
Notifications for high and low room temps.
There have been a few occasions when a Tado smart radiator valve has come loose from the radiator and allowed unrestricted flow. This resulted in the room overheating. To identify when this happened used IFTTT to monitor room temp and alert me if they were too high or too low. I want to reduce my reliance on IFTTT and I…
-
Smoke sensor Tado
Is there any Tado smoke sensor to be merged with Tado app and heating wireless receiver? If no, is Tado planning to release something related in the future? I just don't want to install "n" number of apps for each smart device I need.
-
Merge "deleted rooms" with a new room created
I have deleted a room and re-configured again due to malfunctioning radiator thermostat. Now in my "heating activity" dashboard it shows the history of this room in "deleted rooms". Is there any ways to merge this deleted room to the new one I've created so the statistics aren't disturbed?
-
Add Months to schdule
I’m a recent newbie to getting this and I found it really good. I think a great idea would be to add months to the schedules rather than just days. This would then be useful for setting the schedules per summer months and winter months.I had a digital thermostat which did that and I found worked well as never had to touch…
-
Allow "Auto" within HomeKit
Many smart heating systems when exposed to HomeKit allow the use of "OFF, HEAT and AUTO", even Drayton Wiser which can only be exposed through a custom made plug-in via homebridge can use AUTO. The AUTO function (at least as I see it) would allow the system to return back to the current schedule. For example, in HomeKit I…
-
App notification for manual TRV changes
There are probably lots of good reasons for this feature but my use case: Young children, so I have the child lock on the TRVs. Technophobic parents and in-laws who can't change the heating when doing child care in the house. Spinning the TRV would be ideal for them. Easiest solution would be for me to disable TRV child…
-
Easy schedule or temperature change
Currently changing schedule is not that easy, we need to go through each device and each time block separately and then adjust it. Most of the time we want to change temperature level but each room might have different time schedule, then we always end up in changing one by one. This is really time consuming and tedious.…
-
Keep history when meter reaches max or new meter is installed/replaced
Frustrating, as Belgium now forces by law to change to a digital meter. It won't be long before more countries will do this, but Tado gives no option to keep the history. A similar situation would be when the gas meter needs replacement due to malfunction or reaches the max digits it can roll to. Support's answer was:…
-
Graphs
It would be nice to see the temperature and humidity or moisture content graphs on the web site as well as on the app
-
Dew-point prevention = minimum temperature based on humidity
Given a specific temperature the air can hold a certain amount of moisture and when this air hits a cold surface it condenses causing moisture and mold. It would make sense to have an option to enable the that the Humidity reading be used to automatically adjust a minimum temperature for a room to Reduce condensation when…
-
Control even and odd weeks respectively
I'm wondering, could it be possible to control schedules for odd and even weeks in the application? Biweekly (even weeks) my two children stays at my place, and biweekly (odd weeks) they stay with their mother. Quite normal nowadays which is why I think it makes good sense to have the option to lower the temperature in the…
-
Data & Analytics Room Selection
Would be nice to have a quick way of changing between rooms in the data and analysis section of the app. Currently need to go all the way back out and back into a different room. A drop down menu to change room would be nice
-
Integrate outside air humidity
Vaak krijg ik van Tado het advies om een venster te openen om de luchtvochtigheid in huis te doen dalen. Dit terwijl het buiten vochtiger is dan binnen. Ik ben geen app ontwikkelaar en ken hier weinig van, maar is er een mogelijkheden om de luchtvochtigheid uit een online weerbericht te halen en zo het advies enkel te…
-
Always On Display Thermostat
The option to have the display shown as always on with further options to also be able to dim or brighten it. The option for it to show current room temperature/set temperature/humidity and also possibly time and date.
-
Support for 0.5 degrees temperature change (Tado Smart AC Control V3+)
Many modern AC units today support temperature change by 0.5C. Please add an ability to users to be able to control more precisely the AC temperature.
-
Better Boost Options
I was pleased to see the boast function for the system but very disappointed that you can't select the temp (25 is way to high for my house), or select to just boost one room/trv. I find that I often want to boost a room for just 10mins, and only being able to boost for 30mins at 25 is wasteful and unnecessary. I see that…
-
Schedule that is NOT internet dependent (safer)!
If you are on holiday and your internet drops, Tado continues with whatever setting it had at the time. In other words, your hot water could be ON for the rest of your holiday, not a good thing (and you will not know about it as you no longer have remote access). This is the one flaw I find in Tado. It appears that…
-
Set each valve by number setting or temperature
Sometimes it's easier to guage what you need to set each radiator valve to, by what number it would have been set to on the old style thermostatic valve.
-
Air Source Heat Pumps
I have just replaced my Tado controlled gas boiler with a Mitsubishi Air Source Heat Pump. I emailed Tado and enquired if they had any experience in using Tado in conjunction with such a device. The reply came back that I should put my enquiry here. Perhaps Christmas has come early! It doesn't seem the logical place to me…
-
Export schedules and name devices
Hey, a couple of things I thought would be worth sharing that could improve the app/experience. 1) the ability to nickname devices within a room. I get the xxx needs new batteries email but don't know which radiator in the room. If I could nickname them I'd know which needs replacing easily rather than needing to check. 2)…
-
Update help/support article 6653049
Regarding this article: https://support.tado.com/en/articles/6653049-the-internet-bridge-doesn-t-connect-to-my-fiber-optic-router-modem-how-can-i-fix-this Even if your router/switch has 1GbE ports that you can configure to 10 Mb/s half-duplex, some devices might still not work with the tado° bridge. One of my switches is a…