-
Protect thermostatic valves from stucking closed during summer (off heating season)
Most thermostatic valves get stuck if they are left in a CLOSED position for an extended period of time. In order to prevent this we could either 1) leave all valves OPEN when heating is off - if the heater does not work, it makes no difference which position the valves are, and in OPEN position they do not stuck. Or 2)…
-
Samsung Smartthings
Hey How do i get Tado radiator to work with Samsung Smartthings - I tried both smartthings app(classic) but no luck :(
-
Mac M1 and the Tado App
Is it possible to allow the app to run on the M1 and M2 series Mac computers ? Not everyone in our home has a smartphone, so it would be nice they can use their laptop to control Tado. I asked this question a year ago but no one seems to care. It requires no extra programming, just a setting to make the app visible on the…
-
Grouping rooms for boost/off
I have our house divided into rooms with timings setup that work majority of the time. But, it would be good to boost multiple rooms at once but not all rooms (eg downstairs). Would be great if you could have boost/off zones that consist of multiple rooms, without it being all rooms.
-
Manual adjust graph axis
I would like to be able to adjust the axis of the temperature graphs in the Tado app. Currently this goes automatically hence graph axes jump every day and is different for each room. That makes it difficult to compare different days or rooms and makes it difficult to observe how quickly a room heats up or cools down. I…
-
Dynamically adjust opening percentage based on rest of system as well as heat demand
A couple of weeks ago I posted a suggestion that users be allowed to set the minimum opening percentage on the smart valves to alleviate water rushing noise. In a separate thread about vibration, a solution was suggested to remove the Tado valve from the radiator nearest the boiler because "…it can happen that the water…
-
Enable eBUS support for Tado X Wireless receiver
The V3+ supports both eBUS and Opentherm however the newer product series X does not support eBUS. Please enable also eBUS support for the X series. I imagine since you have the code for V3+ in the firmware it could be refactored over for the X and with a firmware update it could work.
-
Icons for each room type
Can you give the ability to select a range of icons that can be applied for each room that we have. The Hot Water icon is a great example of a visual icon that is easy to see very quickly. We have 14 buttons for heating rooms in our house and it would be very helpful if there were icons for different rooms. For example,…
-
Enable tado on wifi without internet
Today I had 6 hours without heating in the winter. My internet was not working for 6 hours. Tado expects the bridge to be connected to internet for smart scheduler to work and connect with wireless thermostats. Why not enable bridge using wifi home without internet? A heating system should never rely on internet. Relying…
-
Making smart schedule more smart
Would be nice have one page in which they are group the history for heating activity of all rooms together, to have more clear when the boiler can be left off reducing one or more temperatures at a certain time. (Sorry for my English)
-
Ability to rename device
When batteries are running low I get an email informing me that a particular device in a specific room has an issue. In some rooms I have 4 radiators. I then have to go round ‘blinking’ the stat multiple and watching all the stats in the room to find which one it is. it would be great to be able to rename or give a…
-
Guest car support
For guests using the home charger, offer the capability to control the charger timings by: - manually setting start and finish state of charge - departure time - make/model of car
-
Worcester Bosch 4000 ems control
Please enable support of EMS / Ebus functionality so Tado can control modulation of this boiler
-
Energy IQ - Better process for when energy meter is replaced
I recently had to have our smart gas meter replaced, because the existing one became faulty. This meant that my meter reading dropped back to zero when the meter was replaced. When I came to enter a meter reading in Energy IQ, it said I could not enter a number lower than the previous reading. I contacted support, they…
-
Schedules and shared custody
I have my kids in shared custody and need to manage the schedule manually to lower heating in their room on the week they are not present. I really think that shared custody is more common these days and that Tado should consider managing that in a easier way in the app so this is dealt with more transparently. I…
-
Hot water override
need an ability to 'boost' hot water for a short period of time. We have a system with a hot water tank. Sometimes we can run low on hot water and need an option to boost it for a short period - say 30/45mins. Currently the app allows you to override the schedule until the next event, inevitably it means you turn on the…
-
allow changing the name of devices
Please allow us to change the names of devices to make it easier to identify them. For example, getting an email that tells me: "We have noticed that the batteries in your Smart Radiator Thermostat VA*******048 in the zone ****** are running low." I have 15 devices and if each device had a name I wouldn't have to waste…
-
[Energy IQ] Allow for new meter and continue entering meter readings
When replacing a meter, it becomes hard to continue entering meter readings as one has to add the last old meter reading to the new meter readings (and sometimes even subtract the first new meter reading from that number too). Under Energy IQ, provide a meter reset button, with for the date of changeover: ++ the first new…
-
Creat a new group for Tado-X users
Mods, can you create a new group for Tado-X usrs. It makes browsing through posts much easier, as V2/3 and X are not compatible with each other, and they do not share the same problems and solutions.
-
Support multiple schedule configurations such as spring etc..
It is very common to want different sets of heating parameters for different occasions. A typical example might be a different set for summer versus winter. Or for when guests are staying versus not. It would be great if the Tado system supported the ability for user's to create multiple named configurations and switch…
-
Combining the best of Tado and Nest?
I realise the title of this post may sound odd or even controversial but here goes. My system is very conventional (read old fashioned) consisting of a 16 year old Viessman 100 WB1 boiler, gravity fed (tank in roof space) and I believe what is called a Y plan layout with separate two-way valves controlling the heating and…
-
Heating System Override switching it on for 1hr, 2hr 3hr or set a time
Strangely, the Tado system allows you switch on the hot water heating for a specified time outside the schedule. But it is not possible to do the same for the heating. Instead, you have go into each device, which is a ridiculously time consuming and fiddly process. Yet, it is standard functionality on most central heating…
-
Merged: Add support for alternative schedules
This discussion has been merged.
-
Funzioni in app
1 ) Sarebbe utile integrare in app la possibilità di variare manualmente la temperatura di mandata dell'acqua. 2) Quando alla caldaia è collegata una sonda esterna utilizzare la temperatura letta da essa ( sicuramente più precisa ) per regolare la temperatura interna perchè i dati del meteo sono troppo generici e succede,…
-
Exposure of additional information to Matter for Tado X Radiator Thermostat
Hello, I'd like to ask if the development roadmap for the Tado X Radiator Thermostats has the exposure of additional entities to Matter planned in the near future? I'd like to see the battery % and also the valve position (valve open %) directly within the connected home automation ecosystem through Matter, which is…
-
Select how long boost hot water for Tado X
I've switched from the V3+ to Tado X due to connection issues with the bridge. With V3+ in the app I could select how long to boost my hot water for with the pencil, this was a vital feature for me. With tado X I can click boost but it is only set for 60 minutes and can't be edited. I see from tado's website this is a…
-
Temp. Return sensor
Having a return temp. Sensor clamped on the radiator will allow more efficient control of the thermostat as it often over shoots on set point. Monitoring the return temp. Will make a huge difference
-
Incorporate fixed costs and taxes in the calculation of energy expenditure
Dear Tado team, I would like to propose an improvement that I consider useful for many users: the possibility of including fixed costs and taxes in the calculation of total energy expenditure. Currently, the application only allows the variable rate per kWh to be entered, which may underestimate the real energy costs, as…
-
Smart AC control to activate AC based on room temperature
Currently the Smart AC control turns on the AC unit at the start of a time block, regardless of the temperature. In my opinion that's a major flaw, because most (all?) home AC units still run their fan even if the room temperature is below the setpoint, so it's a waste of energy and also annoying to have the fan blowing…
-
Ebus Max Flow Temperature setting (like the one just released for Opentherm).
Would it be possible to do the same for Ebus controlled boilers via the wired Tado, +- settings? My Vaillant can ramp up to 80C if it wants even if I set the max temp lower on the boiler. The ebus will ignore these settings and do what it feels is best. I might only want it to go to 66 or 70C max for example. It's just…