-
Change schedule change for all rooms simultaneously
I would like a simple method to change the schedule for ALL rooms by the same time simultaneously. i.e My heating profile is set to start at 6 am and to warm the house in stages by 8 am. For next week only I want to bring that forward 2 hours. Currently, it seems that I have to change the schedule for each room…
-
Reduce the comfort temperature range to 18-21°c
In the uk a room set for the comfort range of over 20°c can far exceed a comfortable temperature. I would suggest reducing this so my app doesn't think my house is cold all the time
-
Bespoke Nom Circular Geofence
Allow a non circular Geofence to be plotted. We have a park near our house that would be good to have outside the geo fence, especially when the wife and kids spend a few hours there. If I reduce the current Geofence radius to exclude the park the Tado App says it's too small.
-
Extend the diameter of the Home Area.
Way back around 2013, when I first fitted a Tado system with an extension kit as a relay control over the boiler, there was a bug in Tado's system. It couldn't locate my actual address correctly on the map and it also allowed me to set the Home Area diameter to as much as 50 miles away from home. Since moving into a very…
-
Change this board to differentiate between actual bugs and actual enhancement requirements
Am getting increasingly concerned that this community board does not differentiate between actual bugs in Tado systems and enhancement requirements. As an example @davidyall recently identified a bug, unequivocally, in the way in which schedules are organised and what happens when there is a manual override. It is possible…
-
TADO heating/hot water controller error messages - viewer
We have been using TADO for 2 years, and recently upgraded with a TADO Hot Water/Heating controller unit. The installation was done by professionals, and it all works... .. Except that the unit has the triangle warning light almost permanently on?! No amount of fault finding and re-checking can seem to diagnose why it is…
-
Room type and management
I would propose one new room type be added namely "hallway". I have many hallway radiators and the current profiles don't really fit any of the default templates. Another thing I have noticed but probably just a bug is the renaming of rooms doesn't seem to reflect on the Android Home screen. Although I have changed the…
-
[suggestion] Change icon for room block
Hi! On the Room & Devices screen you have a list of blocks. Each block represents room and devices located in this room. It's clear when you see right arrow icon for the device. Once pressing you see device settings screen. But when I see the same arrow for the room - it's not clear what it does. Actually it opens a screen…
-
Suggestion: enable Homekit Away/ Home automation
Tado should allow homekit users to toggle the home / away status of tado, using homekit automations. Issues; - Expensive - Tado charges £29.99/y just to toggle auto geofencing (extortion). - Privacy issues - I have to always share my location data with tado. I don't want to do this. - No support for guest / multi house…
-
Less confusion about being at home
The Tado app has a small piece of code in the Geofencing area which pulls the trigger defining that one is at home, by recognising a home network and logging into it. It has a small oversight which confuses it. In an old thick walled house it is often necessary to fit wireless repeaters or powerline wireless nodes. They…
-
Tado X and home assistants (adding important elements)
I added official integration, but for tado x I see only outsite temp, localization, solar energy (prediction) and tado mode nothing else. I need hetting status, actual temp., sett. temp., humidity , opened window status, etc. For all added thermostats. For version V3+ all info is available in home assistant (google home…
-
Global slider to adjust temperature within schedules.
Could we have a global setting to increase or decrease the temperature asked for by the TRVs whilst in a current running schedule. For example I have a current schedule running for beginning of Autumn here in the UK, but sometimes it's colder than expected or even a bit warmer than expected. The ability to adjust a global…
-
API Integration for Energy IQ
I use the energy provider Octopus In the UK, and they provide me with an API key for my account that can be used for getting meter readings and other things. It would be so good if, in Energy IQ, I could put in the API key so that the meter reading were added automatically.
-
Energy IQ - Usage is not based on actual meter readings
We were away from home for about one week and wanted to try an experiment with usage data. Our heating was in away mode throughout and did not switch on. I submitted regular meter readings within Energy IQ at the start of April, then on the day we left, and as soon as we returned, and on the following day. The meter…
-
Air source heat pump linked to UK's Octopus Energy Agile Tariff
Tado should add the ability to heat up the water cylinder using an air source heat pump based on the cheapest energy rate of the UK's Octopus Energy Agile Tariff. This could save lots of £. It would need some AI or the like to spot what is likely to be the cheapest rate for the day, though that may be quite stable and for…
-
Add command ON/OFF of the system in the wireless sensor Thermostat
Hi is possible add to the wireless sensor thermostat the command of on/off of the system, like is in the app of mobile. The same way that the temperature of the hot water is adjusted to the thermostat menu. Thank
-
Ensure that Tado Support reply to support requests
Hello, I have messaged tado customer support numerous times over the past few days (including setting up new message threads). However, I have not received a reply. My suggestion for improvement is that you improve this situation and make sure requests for support are answered. Mine is quite urgent because my tado has…
-
App Ideas - 'call for heat' alignment
Issue: my heating is on a lot through the day. I'd like better visibility of when the boiler has been triggered (called for heat) and by what. And better control so I can (or the system automatically will) try to align devices calling for heat (so perhaps 3 devices call for heat together for an hour, then all go off for an…
-
Adjust support expectations; replace the bot with a form
tl;dr: Having a support chat is giving a false impression of one actually getting one-on-one, immediate support. I do however understand why tado absolutely wants people to go through the bot instead of just sending an email. So how about we compromise and everyone gets something they want… Long version: Looking through…
-
Daikin Heat Pump Compatibility
I am looking for a smart home heating solution and contacted support to assess compatibility for Tado X which states it accommodates under floor systems. Support informed me that Tado X is not compatible with Daikin Altherma R F - EHVH-CB and Daikin ERLQ006CAV3. I would suggest adding compatibility as this is a widely…
-
Tado X suggestions
(I originally messaged this direct to Tado but they asked me to repost it here.) I have read that currently your Tado X heat pump controller supports only some makes of ASHP as of yet but based on customer requests you will add more. I am therefore contacting you to suggest both Samsung Mono HT Quiet, and Daikin Altherma 3…
-
All room graphs in 1 place
Please offer either a consolidated graph for all rooms, or an easier way ('next, next, next...') to browse the room graphs. Currently it's tedious to exit each room page, enter the other, tap the graph icon; repeated x times.
-
Maximum opening percent and time on radiator thermostate
To ensure not to send hot water out of the radiator, it could be helpfull to could adjust the maximum opening percentage combined with maximum opening time, followed with a minimum closing time.
-
24 hour clock
The smart schedules are set using the. 24 hour clock. However, the next event for each room uses am/pm. I know I live in the UK with its outdated time but it would be useful for users to select a consistent 24 hour (or am/pm) format.
-
Boiler Immergas compatibility with digital bus
I just bought an immergas victrix extra 32 boiler and found that it is not compatible with the digital bus and I had to connect it to the on/off relay. can you make it compatible please? Thank you
-
Merged: Manage more than only one home-house in one/each account
This discussion has been merged.
-
Away/home status in Alexa
Hello, Since ifttt is OUT, it's important to have the tado status return on Alexa routine. We need to have this information: away, home. I think it's the same for google. Regard
-
Low/High humidity notifications
Would be great for Tado app to send a notification when a room has low or high Humidity, with the ability to set the level that the notification can be triggered.
-
Activate open window detection with external window sensors
I would like to be able to use my window/door sensors to activate ‘open window detected’. This would be a great improvement as it will speed up this process and will keep ‘open window detected’ on until I close window/door. I know this can be done indirectly by setting the heater to “off” with ifttt but this means that it…
-
Set a manual time limit on Manual Away Mode to go back to auto.
Set a manual time limit on Manual Away Mode to go back to auto similar to the manual timer mode on the TRVs/Thermostats.