I use the energy provider Octopus In the UK, and they provide me with an API key for my account that can be used for getting meter readings and other things. It would be so good if, in Energy IQ, I co…
We were away from home for about one week and wanted to try an experiment with usage data. Our heating was in away mode throughout and did not switch on. I submitted regular meter readings within Ener…
Tado should add the ability to heat up the water cylinder using an air source heat pump based on the cheapest energy rate of the UK's Octopus Energy Agile Tariff. This could save lots of £. It would n…
Hi is possible add to the wireless sensor thermostat the command of on/off of the system, like is in the app of mobile. The same way that the temperature of the hot water is adjusted to the thermostat…
Hello, I have messaged tado customer support numerous times over the past few days (including setting up new message threads). However, I have not received a reply. My suggestion for improvement is th…
Issue: my heating is on a lot through the day. I'd like better visibility of when the boiler has been triggered (called for heat) and by what. And better control so I can (or the system automatically …
(I originally messaged this direct to Tado but they asked me to repost it here.) I have read that currently your Tado X heat pump controller supports only some makes of ASHP as of yet but based on cus…
Please offer either a consolidated graph for all rooms, or an easier way ('next, next, next...') to browse the room graphs. Currently it's tedious to exit each room page, enter the other, tap the grap…
To ensure not to send hot water out of the radiator, it could be helpfull to could adjust the maximum opening percentage combined with maximum opening time, followed with a minimum closing time.
The smart schedules are set using the. 24 hour clock. However, the next event for each room uses am/pm. I know I live in the UK with its outdated time but it would be useful for users to select a cons…
I just bought an immergas victrix extra 32 boiler and found that it is not compatible with the digital bus and I had to connect it to the on/off relay. can you make it compatible please? Thank you
Hello, Since ifttt is OUT, it's important to have the tado status return on Alexa routine. We need to have this information: away, home. I think it's the same for google. Regard
Would be great for Tado app to send a notification when a room has low or high Humidity, with the ability to set the level that the notification can be triggered.
I would like to be able to use my window/door sensors to activate ‘open window detected’. This would be a great improvement as it will speed up this process and will keep ‘open window detected’ on unt…
Issue The air condition Midea Silent Cool 26 Pro WF is equipped with a so-called "Follow Me" functionality. Activating the feature via the included remote control or on the device itself makes the AC …
Bring the iOS Tado app to the Mac AppStore to use the features in which HomeKit doesn't support (Ie. Override Timer, energy reports, timer settings). When we had access to run these apps pre MacOS 14.…
Hi! It would be great to have couple of additional sensor types to allow more customised routines: - presence/motion sensor - door/window open sensor These sensors could be additional conditions to th…
The ideal temperature in a room or zone is a matter of personal choice. The degree of humidity is a matter of climate. These vary and should be capable of choice and customisation not a level of humid…
Hi, I've created a new post to again highlight the importance of this to Tado. Without 2 factor authentication/MFA, Tado will soon be in breach of EU law. In 2022, the EU Commission proposed the Cyber…
The Tado extension kit can control the boiler through a relay (simple on-off switch) or through the Opentherm bus. The bus allows for better temperature stability and higher efficiency as it tells the…
Is there any reason why the only options in HomeKit are cooling, heating and off? In the Tado app I can see that it knows the commands for auto mode, dry mode, fan mode, fan speed, tilt, fixed etc. Ho…
Hi Everyone, the Tado internet bridge has three very bright LED lights. I would like to have the possibility to disable those LED lights please. A configuration as described below could be useful for …
I have a few rooms with smart TRVs and it always takes me a while to find which room is requesting heat. It would be easier if there is a little logo, or maybe a coloured border around the room icon i…
Apologies if this has been raised before but I couldn’t find a reference. When setting the system to “Away” provide an option to revert to “Home” either by setting a future date (preferred option) or …
Please create a function where we can use Tado with a heat pump (equipped with a cooling function) connected to a floor heating system to cool the rooms (with Tado thermostat) to the specified tempera…
