-
Behaviour of Zoned vs Independent TRVs . . .
I wonder whether anyone else feels that the tadoº TRVs behave differently with regard to opening and closing when they are set to independent in contrast to when they are assigned to a zone controller and able to call for heat. For this year’s heating season I have made several of the TRVs in the “communal” areas of the…
-
Tado app working and all devices connected but boiler not firing up when the app calls for heat
My system is about 7 years old, not sure what version but is hard wired with an internet bridge and extension kit. In the last week, the boiler has stopped firing up when tado calls for heating or hot water. I then have to switch everything off and then on (bridge/extension kit & boiler) and it starts. Has anyone had this…
-
Tado X TRV not causing a heat call
Hi, I've recently bought 2 X TRVs and a thermostat, and an x bridge. One trv and the thermostat are located in the bathroom, the second trv is in the bedroom. When I set the temperature target in both bathroom and bedroom to a higer temperature than the actual temperature the thermostat does a heat call to the boiler.…
-
Vokera Syntesi - hot water but no heating
I have had a tado installed it is all connected to each other and can see everything on app, but when I increase heating in the app it doesn't switch the boiler on. Hot water works but no heating. I would appreciate any suggestions, I put it into test mode and it kicked the boiler in the straight off again.
-
Wireless receiver not connecting to bridge so boiler doesn't respond and schedule not stuck to
Moved into a house last month with Tado. Set up an account okay and connected to the thermostat. Internet bridge set-up next to internet router but seemed too far away to connect to the receiver which is connected to the boiler. Took the time to buy a WiFi booster so the internet bridge is now connected much closer to the…
-
Changing over from Danfoss to Tado
I have a Worcester green star AR 24i boiler, CH and HW with a hot water tank upstairs My current Danfoss system is a CP715 Si controller in utility room and a wired RMT 230 thermostat in the hallway. I purchased the V3+ wireless starter kit I disconnected the wired Danfoss thermostat in the hall way. I then removed the…
-
V3+ not calling for heat
Bit of background - bought a Hive but realised it was not WiFi, so bought this instead. So the boiler (Morco GB24) has a simple timer switch (heating only being controlled). Fitting the Hive meant using grey wire 4 to the NO side of the timer switch and linking Common and Live on the Hive side leaving the switch in the…
-
New DIY install replacing TP9000
I have a viessmann system boiler and hot water tank controlled by a Danfoss TP9000 on the 1st floor landing which schedules the HW and CH. I'm looking to DIY install the Tado V3+ Wireless Heating & Hot Water Smart Thermostat Starter Kit. I'll replace the TP9000 (no remote sensors) with the wireless reciever which appears…
-
Setup for centralized heating without direct boiler control
Hello, I need an advise which setup to use to control my house heating. I have centralized heating in my condominium, which is not under my control. I have a radiators with manual valves and I want to replace these manual valves with the ones that can control ambient temperature in the room. My questions: is built-in valve…
-
Potentially fried my wireless receiver? Advice needed.
With winter around the corner, I decided to replace my Strom SSRTPR05 wall mounted wired thermostat with the tado wireless smart thermostat starter kit V3+ (with stand). I live in a new build flat than came with a Strom thermostat, which just lifts off the wall and away from the circuit attachment. It has a 2 wire setup…
-
Guide for replacing faulty Tado wired smart thermostat with a new one?
I've 2x Tado wired smart thermostats (upstairs and downstairs heating) and 1x extension bridge (for hot water) The downstairs smart thermostat went offline a few days ago and won't come back. It controls heating downstairs and the hot water via an extension bridge. Tried all the usual re-pairing, moving the bridge beside…
-
Tado kit with central heating
Hi everyone, in my house I have 4 radiators and 2 towel warmers with mechanical thermostatic valves and I can switch on the heating with a thermostat always in my house. Usually my use was with manual switch, for a few hours,in the afternoon/evening so as to heat the rooms but the central heating switch off from 23:00 pm…
-
How do I contact tado direct
How can I get in touch with Tado support with a specific question
-
E1 error
Have removed the child lock on a Tado smart rv and when correctly reinstalled I get permanent E1.
-
3-day standard for help line answers?
Do I get it right that the helpline needs 3 days to reply to requests? What is the standard for response time?
-
App not showing data
I have recently updated the app due to an error message I was receiving and since then it no longer shows when the heating has been on/off. Also, previously I was able to control the amount of time the heating was on for and any following Alexa requests would put the heating on for the amount of time specified previously.…
-
Installation
I have a Worcester Greenstar 30si boiler with Siemens RAA200 hard wired controls and I want to fit the Tado hardwired thermostat it place of existing controls. My Siemens room stat wiring diagram shows 2 cables 1 into L and other cable into Y1. Where would I put these cables on the tado stat
-
If I have smart radiator thermostat in every room is there much use for the wireless thermostat
Question is in the title. I have smart radiator thermostat in every room and can control the temp from my phone, so is there any reason to have the general smart thermostat on my wall? Also is there any way to see a history of when my heating turns on? I can see a history per radiator but I wanted an overall view to make…
-
add-on wireless temp sensor or add-on smart thermostat?
quick question. i have a tado sytem already in place (uk combi boiler), controlling just heating 1 zone. 3 rads with smart trvs. smart thermostat running as a wireless temp sensor. i want to add a wirless temp sensor in the other 2 rooms that only have the smart TRVs for better/more accurate temps. on the store they have a…
-
Tado Configuration
I currently have an Ideal Logic+ System S15 gas boiler which has 3 outgoing copper pipes. one for hot water to a tank upstairs fitted with an immersion heater, filling of which is from the main water, one is for upstairs radiators and the third for downstairs radiators. I'm assuming this is classed as three zones(?). On…
-
Boiler only comes on when heating is on but not when only hot water is on
Hi, I have a strange issue where the boiler only fires when I turn on the central heating, this turns on both the central heating and hot water. Turning just the hot water on, it show in Tado receiver that the hot water is on but the boiler doesn't fire. I believe I have a S plan and the 3rd and 4th pictures are of the…
-
Romm thermostat not calling Combi Boiler on
I have two room thermostats one upstairs hydraulics, one downstairs, the one upstairs working fine, but the stat downstairs fails to night the boiler when the schedule calls, it was working last season fine, any ideas ?
-
Keeps dropping off network - too many cold showers
I've had an early Tado system for several years and the connection to the network drops every couple of weeks or so, something I only notice when we have no hot water. This has been going on for some time and I'm at the point of ripping out the system and installing something that works. When it happens, the Tado box only…
-
What is the wiring to connect a wired thermostat to a relay
I wish to connect a wired thermostat to a Salus relay. It should be pretty straightforward, but can someone confirm which terminals to use for the mains input and the relay output?
-
Wireless Thermostat not switching on boiler
Hi, we have 5 radiators with wireless thermostats, the one in my sons bedroom will not activate the boiler, all connect fine in app, shows no issues on app, switch the radiator on in his room, temperature changes on the thermostat but nothing from the boiler, we have to switch another room on to get his radiator to heat…
-
Can I remove hot water control from the app
As I have a combi boiler, I don't need hot water control in my account, so is there any way of disabling or removing it?
-
Has the geofencing control toggle that used to appear when editing a time block disappeared for anyo
There used to be an 'advanced settings' section with a Geofencing control switch - but this morning I noticed it isn't there for me. It's still there when I add a new time block, but when I go to edit an existing time block I don't have it any more. Strange.
-
Intergas Xtreme 36 modulation with Tado
Yesterday I had my 15-year-old AWB Thermomaster replaced with an Intergas Xtreme 36. On my old AWB, once the modulation was set via EBUS (D07 on Tado), I could see the modulation temperature of the kettle on display. Now with the Intergas, the setting has been changed to D01 but when I click on the radiator icon on the…
-
tado v2 behaviour
I have a tado wired (relay) stat and the v2 bridge (the soap bar style one without the homekit integration). Relay rather than digital setup. Now its heating season, all the 'strange' things tado does are back and annoying me like before so I just wanted to see if anyone else is seeing the same behaviour or if I need some…
-
What do I need to connect my tado?
Hi, Does anyone know how I can convert my old Giacomini radiator from lock shield to TRV valve? (The info I have is it may be 15mm-3/4" tall) I am worried I'm going to have to buy the full TRV valve on top of the Tado - does Tado supply the TRV valve? Cheers