-
Cannot get the internet bridge to connect through my TP-link router (EE sim)
I've had a Tado at home for years (bridge and wired thermostat) and never had any problems. We are trying to fit one in a Lodge with a Morco GB24 Series 3 boiler and need a V3 Tado as there's no room thermostat (receiver, bridge and room sensor). The bridge will not connect to the router (TP-Link TL-MR6400 with an EE Sim…
-
thermostat X LEDs
What to do so that the tado x thermostat shows the temperature permanently
-
Tado Heat x optimizer & Daikin Altherma R3
Hello, I have a Daikin Altherma R3 heat pump air to water. it has a lan adapter connected but unfortunately this adapter is very cumbersome to use and primarily to connect to, this makes it almost impossible to do minor changes in the heating schedule. due to this I am looking at the Heat X optimizer as a mean to get a…
-
Accessory is not reachable in Homekit
So my bridge lost connection with HomeKit. It works fine in the Tado app, I can access Home and Tado away from home so I know my network is fine. Can see Philips hue in HomeKit. I tried a reset and hard reset. I can see the bridge when I use camera and it grabs the numbers. I click the bridge and it says connecting, then…
-
Strange noise in the night
Hi all One of my tado radiator valves has been making a strange noise in the night (usually this one will be the only one on) this used to only be occasionally but it has got worse and is now every night. I have videod this and linked in here https://app.box.com/s/f2emw5eaau01s0lh00li9o0oumiy6ojs I have tried removing and…
-
Thermostat V3 cycles between on and off too often
I've noticed recently my Thermostat is opening and closing the relais quite often. The boiler activates for maybe a minute and then turns off again. This is not sufficient to get the water into the whole system. Yet, the care & protect is reporting it is 100% heating several rooms. This behaviour makes that the rooms are…
-
Can i set a maximum value for the heating water temperature?
I have a tado v3+ device. I connected the wireless receiver to the Ariston gas boiler via eBus. everything is going well, but the thermostat sometimes sets the heating water temperature too high. Is there a way to set a maximum temperature above which the heating water is not heated?
-
Vaillant and Hot Water
Got a Vaillant EcoTEC Plus VU30 CS/1-5 with a external hot water tank. My Tado v3 extension kit is connected to the ebus and is recognized by the boiler. In the boiler panel I cannot control the heating circuit (only can control in tado app) and it works ok. I configured the boiler in the app and in the thermostat to use…
-
EU tado with s plan ch +ufh
Hi all, 1st post here and trying to figure out.. I have not long done a renovation and installed a main eco30 combi, I also have a ufh wet system in my extension which hasn't been wired in, I have just installed 2 zone valves. I'm now at the point where I need to wire them up. Ch is one system through the house with tado…
-
What happened to my post?
I just posted https://community.tado.com/en-gb/discussion/26041/atdvanced-system-compatibility-and-boiler-modulation/ and it's not visible anywhere? What happened? Can an admin re-instate.
-
Internet Bandwith Consumption
Since November 2024 I have three tado Smart Thermostats and a tado Bridge X running. My internet connection is a 40 GB/month mobile broadband, which has worked fine for our household since January 2024 with no loss in accumulated monthly bandwith. Five days ago, by accident, I discovered that there was only 15 GB left and…
-
Tado Thermostat X has no Device Linking option within the app
Hello, I have successfully paired my Tado X Thermostat and Bridge X to my home network. I can control the thermostat via the Tado app without any issues. However, I'm now trying to pair my Tado X to my Home Assistant instance. In order to do that, I require a setup code. It is my understanding that I should be able to get…
-
Where to buy parts?
I managed to break the thermostat head nut - it's a bit fragile isn't it? Can I order spare parts like only the nut itself or the complete set that includes the plastic part (excluding the thermostat)? If these are not for sale anywhere, can anyone share recommendations of compatible nuts that I could use to replace it? My…
-
Installing Extension Kit with Hot Water Cylinder
Hello, as the Tado chat is pretty much not responding and they closed their phone lines, I am hoping someone here can help. We have a Vaillant UniStor unvented hot water cylinder and a Vaillant EcoTec plus 618 condensing boiler. There is a Honeywell ST9400C control for hot water and heat next to the hot water tank.…
-
Tado X - Month 2 Review / Feedback Needed.
Hello, Having been a Tado customer for 4-5yrs, and vocal about the lack of additional bridge support for the v2/3 platform, i jumped on the opportunity to upgrade to X to finally solve connectivity issues around my home. Now that i've been using X for 2 months, here is an honest summary of my experience, and some issues…
-
Can no longer control heating/hot water via Google Home - devices offline
A couple of days ago I suddenly found that I can no longer control my boiler via Google Home. When I say, for instance "Turn on heating", it just says: Sorry, I couldn't reach Tado degree That's a new one one meI I've had intermittent issues in the past, but have never heard Google refer to "Tado degree". That makes me…
-
Matter Device Linking
As many will know I have a Tado X system, 16 x Rad valves with Wireless X Receiver. I use the Tado Android App on a Pixel Fold 1 running Android 15. Since I had this system I have tried a number of times to use the Matter Device Linking option. I have been able to make it work only by factory resetting the Rad Valves. The…
-
New TADO installation - Thermostat and TRV
Hi we have just had a new TADO install and have smart TRVs on every radiator. We also have a TADO wireless thermostat. I am now controlling and setting the radiator TRV via the app and I can’t work out what the point of the wireless thermostat now is. Can I simply disconnect it and forget about it? thanks Ken
-
Problem with programming in different rooms of the house
I have purchased a smart thermostat and two smart thermostatic heads tado X, as well as a bridge. The smart thermostat is located in the living room, and the smart thermostatic heads are in two bedrooms. The temperature schedule is the same for all three rooms. The problem I have is that when the desired temperature is…
-
Can I use the smart thermostat to control a plinth heater
Hi, I have an extension kit, smart thermostat & TRV's controlling a combi. All works well. In my kitchen I have a wet plinth heater. So when the boiler fires up, a thermostat on the water pipe inside the heater switches the fan on and blows warm air into my kitchen. I'd like to try and get better control of this by using…
-
Who to wire to Installing Tado Starter V3+ kit with Worcester Bosch Greenstar 30 si?
Who to wire to Installing Tado Starter V3+ kit wired with Worcester Bosch Greenstar 30 from Drayton thermostat? Do I put it on a digital ( N with - and L with +) and any additional wires I need to isolate? Thank you in advance for your help.
-
Greenstar 28i with digistat optimiser
I have installed a tado system into our WB greenstar 28i which has the digital clock /RF unit. The tado works on its own and you can hear the relay click when you set a demand for CH, but this does not fire the boiler. The remote Digistat optimiser still operates the CH, and I can't figure out how to change this over. Any…
-
TRV temperature setting vs room temperature
Hi All, I am planning to buy a full Tado system but I wonder if the TRV is measuring the temperature and it is mounted to the radiator, how could it give you the precise heat in the room what you need? As far as I know the max temp is 25 Celsius on the TRV, so is it enough to heat up the room to 21-22 Celsius? Thanks for…
-
Baxi System 100he boiler
I'm thinking of buying Tado V3+ Wireless Heating & Hot Water Smart Thermostat Starter Kit and Smart radiator valves. Does anyone know if they are compatible?
-
Have new phone.
Can I use my current Tado log in details on the new phone. Sorry for being dumb on this but will I have to go through setting up again on the phone or once app downloaded on phone it will recognise the Tado equipment. Thank You
-
How do I post images in a post
How do I post images in a post?
-
Replacing Myson MPRT with Wired Tado – Second Wireless Zone Compatibility and Setup Questions
Hi everyone, I’m planning to upgrade my thermostat setup and recently purchased the Tado Wired Smart Thermostat Starter Kit V3+ to replace my wired Myson MPRT (in the living room). The wired Myson is currently not working and controls the heating for the living room, kitchen, hallway, and bathroom. In addition, my bedrooms…
-
Buying advice please, replacing old wireless Honeywell
Afternoon all. My old RF wireless Honeywell thermostat has packed in, so I need to replace it. It is a pretty standard thing, only turning the combi boiler on and off, and that's it. I saw the Tado Smart Thermostat X and also a similar looking wireless version. Would the wireless version be what I need, and would that be…
-
How to supply power to the EU opentherm receiver in UK?
As title states, how could one supply power/wired the EU opentherm wireless receiver in the UK for modulation? I understand it comes with EU plug already attached according to the description. I have three basic ideas, though one may not be all that smart/safe, idk 😂 1. Just use an EU to UK plug adaptor. 2. Actually have…
-
I need to replace my failed tado wired stat
My current stat has failed and will not switch pump off. Is there an easy way to swap out old tado stat for new one ordered?